Search Documents

Jan 1, 2004

In recent years it has been more and more recognised that applied geology can be of service to the mining industry, and many mining companies overseas now have permanent geological staff as part of the operating organisation.Most of these companies insist that the geological department must pay for itself by the savings it can make in operating cost, and the growing use of the geologist is proof that such savings are made.The geological problems in every district are different, and a description of the problems and method of attack in a specified district is a useful addition to the literature of mining geology. Very few contributions, from the standpoint of the mining company geologist, have appeared in the Australian literature so that, although the operations of Bendigo Mines Limited are still in the development stage, and its geological work newly established, a description of the routine geological work at Bendigo should beof interest.Although most Bendigo mining companies have not employed permanent geologists, they have utilised geological guidance wherever possible, and a great body of data has grown up. Acknowledgment is made here to the valuable work of the Geological Survey of Victoria, especially the writings of E. J. Dunn, H. Herman, and H. S. Whitelaw, and the maps of Caleb Thomas and H. S. Whitelaw; and also to the work of independent investigators, notably Chief Geologist, Bendigo Mines Ltd.

Jan 1, 1936

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

This international symposium was convened to assess the current state of knowledge concerning the health hazards that might be associated with the ingestion and inhalation of fibrous particles produced from the processing of taconite ore. Concern about fibrous particles in taconite arose from their similarities to amphibole asbestos minerals that are known to be human carcinogens. The mineralogical characteristics of asbestos fibers are reviewed and compared with the fibrous particles known to be present in taconite ore from the eastern end of the Iron Range. The epidemiological and experimental animal studies for asbestos-related disease (including gastrointestinal cancer from asbestos in dinking water)were critically evaluated andcompared to those of the fibrous minerals in the taconite. The focus was on the amphiboles in the cummingtonite?grunerite and tremolite?ferroactinolite series and other fibrous particles in both the Iron Range and the Duluth Complex. This included examination of the reported occurrence of any asbestiform ferroactinolite, crocidolite asbestos, chrysotile asbestos, etc. In addition, an effort was made to provide a scientific framework to address fibrous minerals, which may be associated with nonferrous mineral deposits in the Duluth Complex. State-of-the-art risk assessment models for asbestos were presented. Risk assessment scenarios were developed for taconite-derived fibers at environmental exposure levels related to the operation of the Silver Bay taconite processing facility. These calculated risks were found to be trivial even after it was assumed that all mineral fibers were as carcinogenic as amphibole asbestos.

Jan 1, 2008

The area (330 sq. miles) shown on the map of the Brocks Creek District (Fig. 1), was mapped by the Northern Territory geological party of the Aerial, Geological and Geophysical Survey of Northern Australia. This work was done in two stages:-(i) In 1935, an area of 30 sq. miles around the Golden Dyke mine was mapped by P. S. Hossfeld, Senior Geologist, and A. H. Voisey, Assistant Geologist. The results were described in a detailed report (10).(ii) In 1939, an area of 300 sq. miles in the Brocks Creek district was mapped by C. J. Sullivan (Senior Assistant Geologist), and V. M. Cottle and S. N. Kiek (Assistant Geologists) under the general supervision of P. S. Hossfeld (Senior Geologist).An outline structural map, together with some geological notes was published (1), but that map does not show the amphibolites, and the relationship between ore occurrence and general geology is not emphasised. The publication of the detailed maps and reportwas postponed indefinitely as a result of war. The original mapping was based on air photographs with a scale of approximately 1 in. to 1,200 ft., and all detail which could be shown at that scale was mapped. Features recorded included rock types, details of structure, mineralisation, and surface workings, creeks and soil boundaries. Underground mapping was also carried out. The present map is much simplified from the original, but it is hoped that it shows sufficient information to reveal close relationship between structure, granite, sills of amphibolite and gold occurrence. About 50 per cent. of the area is covered by deep soil or alluvium, and in these portions the geology of the underlying rocks was not determined with accuracy, though in many places strike trends could be deduced from air photographs.Because the A.G. & G.S.N.A. had published the geological notes and map referred to above, and because the publication of the detailed report and maps is still postponed indefinitely, approval has been given by the Bureau of Mineral Resources, Geology and Geophysics (which took over the affairs of the A.G. & G.S.N.A. at the termination of its operations) to the preparation of the present paper so that information would be available to the public.The views expressed in this report are those of author. The results of the investigation suggest that in areas where granites are predominantly concordant with bedding, ore deposits may be found at approximately the same stratigraphic horizon. It is thus important to correlate beds even though their relationship may have been obscured by faulting and folding.

Jan 1, 1950

By Clement K. Chase

Since the dawn of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extraction. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By R. W. Heins, N. Street

An investigation was made of the Rehbinder-Kuznetsov pendulum as an instrument to aid in the study of rock drillability and of the effect of surface active agents on rock drillability. The "critical weight", i.e., the pendulum weight at greatest sensitivity, was determined for several solids and it was shown that a change in surface environment changed the maximum value of the apparent hardness but not the critical weight, and the critical weight increased with increase of hardness of the solid used. Using silver halides as the solid material, and solutions of either silver nitrate or the appropriate alkali halide, it was shown that there is a hardness maximum at the zero point of charge of the particular silver halide. INTRODUCTION The development of relative hardness measurement by the method of damped oscillations, or what has been called the pendulum sclerometer, is due largely to the Russian workers P. A. Rehbinder and V. D. Kuznetsov and their co-workers.1,2 The apparent simplicity of the method has led to its use in a number of fields, particularly those where relative hardness has to be determined on a brittle solid. As will be shown, the simplicity of the method belies its complexities. THEORY OF THE PENDULUM SCLEROMETER The operation of the pendulum is quite simple. Make a sharp point such as a diamond, hardened steel or tungsten carbide, as the fulcrum of a pendulum, with the center of gravity of the system below the point of support. The attenuation of this pendulum is a function only of air friction, provided no fragmentation, breakage or other work is performed by the point. However, when the solid surface breaks or disintegrates under the point, and the latter penetrates the solid, part of the energy of oscillation is absorbed in the work of creating new surface, and the rate of attenuation increases. In the case of brittle solids, the point of the pendulum produces fragmentary particles, whereas the point produces plastic deformation in a plastic solid; but in both cases damping occurs. This pendulum damping is a function of the hardness or strength of the solid. Whereas a pendulum oscillating on a hard material attenuates primarily by air friction, in the case of a soft material, the points penetrate the surface of the solid, producing new surface, and the pendulum damps much faster. Thus the attenuation rate is a function of the hardness or strength of a material in both plastic and brittle substances. Russian workers initially used a single support for the pendulum, but this created many problems because of oscillation of the pendulum in more than one plane. A revised version used two points, or sometimes a prism as support, successfully confining oscillation to one plane. The version using two points was constructed and used throughout this investigation, making the recording of the attenuation as a function of time relatively easy. That both points should be in contact with the solid during the damping is implied. Rehbinder (c.f. Kuznetsov2) proposed that the hardness H as measured by this method could be expressed by a quantity which is inversely proportional to the relative initial rate of attenuation of amplitude. where H = hardness parameter (arbitrary units) a, = initial amplitude da/dt = rate of attenuation of amplitude with time. In the simplest case of damping with a constant logarithmic decrement, H can be regarded as a constant for the duration of the whole damped oscillation process. That is

Jan 1, 1966

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

Utilizing a very large database from a mined-out area on a South African gold mine, the relative efficacy of a method to mitigate the smoothing effect introduced by the algorithmic constraints imposed by kriging was investigated. Smoothing effects arising from limited data availability are differentiated from the smoothing arising from the application of estimation algorithms. Very little can be done to ameliorate smoothing of estimates because of too little data, barring additional drilling or sampling. However, the smoothing effects resulting from the kriging process are shown to be mitigated by use of an alternative algorithm. The primary criterion in the development of the new algorithm was to avoid re-introducing conditional bias. This paper examines firstly the smoothing effects introduced into estimates via the kriging covariance matrix, secondly the process for ameliorating the smoothing effect, and finally it uses a case study to demonstrate the effectiveness of the new algorithm on a very large database. The database was used to introduce a 60 m by 60 m drilling pattern which in turn was used to model the semi-variogram and produce 30 m by 30 m kriged block estimates. The follow-up database was then re-introduced (roughly 5 m by 5 m grid spacing) and averaged into 30 m by 30 m blocks to provide a direct comparison with the initial estimates. In this way the extent of smoothing and accuracy of the estimates before and after the corrections was tested.

Jan 1, 2014

By I. H. Wong

The large diameter caisson foundations and their construction methods for three 50 to 60 storey high buildings in Singapore are described. The caissons are 5 m to 8 m in diameter and 40 m to 100 m deep, excavated either by hand or mechanised excavators or by drilling and blasting. Performance of the 50 storey DBS Building is described.

Jan 1, 2010

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation's Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

THE science of topography deals with the various natural and physical features of the earth's surface. These features are determined by the manifold constructive and destructive processes of nature, and their many diverse forms and characteristicsare dependent primarily upon geologic structure. Thus it is that a close relationship exists between the rocks of a region and the topographic features of the lJountry wherein they occur. Again, the existence of all sorts of mineral wealth is dependentupon the nature of the rocks, and their extension is directly connected with the topographic features represented upon the enclosing land-area.In studying any district with a view to deciphering its geological structure, to locating any mineral deposits it may contain, and to ascertaining, so far as a surface-examination may show, their probable and economic possibilities, it is therefore ofprimary importance to have at hand a correct topographical map of the area under investigation.GENERAL REMARKSThe actual amount of topographic detail shown will depend upon the money and time available for topographic surveying and upon the scale upon which the final map is to be produced...

Jan 1, 1912

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

By G A. Challis, A B. Christiel

Microprobe analyses of electrum grains in some Hauraki Au-Ag deposits indicate that gold fineness is in the range of 500 - 800 (50 - 80 per cent Au), but for most deposits the range is usually narrower than this. The electrums contain minor amounts (<0.8 per cent) of copper, arsenic, antimony, mercury, iron, and sulphur. Platinum and palladium were analysed for but were not detected (detection limit 0.24 per cent for Pt or Pd). For some deposits (eg Waihi), the average fineness values for the analysed electrums correspond fairly well with the electrum fineness determined by assay during the historic mining operations.

Jan 1, 1992

By B. L. Eggers

This study investigates the application of computed order tracking with subsequent rotation domain averaging and statistical analysis, to the drag gearbox of a dragline used in a mining environment. Computed order tracking is a fault detection method developed to deal with the varying speed conditions often found in industry and has been proven effective in laboratory conditions. Its application to real situations, however, requires some adjustment to deal with issues such as inadequate speed data and the fact that the drag gear rotates in two directions. This provides a unique opportunity to observe the performance of the order tracking method in a bi-directional rotating environment, allowing an investigation of the relationships between the results obtained from each operating direction. A monitoring station was set up aboard the dragline and data was captured twice daily for a period spanning approximately one year. The data captured consisted of accelerometer and proximity sensor data. The key on the shaft triggers the proximity sensors, allowing speed and direction to be measured. The measured speed is interpolated by using various speed interpolation techniques. Then the interpolated speed is used to complete the order tracking procedure that resamples the vibration data with reference to the speed. The results indicate that computed order tracking can be successfully employed in real environments. Furthermore it is shown that the rotation direction that opens the gear-tooth crack gives a better indication of incipient failure. It is therefore important not to disregard either direction when monitoring rotating machinery of this kind.

Jan 1, 2007