Search Documents

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By L. D. Tracy

This is the third of the series of reports on coal-mine royalties and leasing conditions in Illinois. The results of the study of District VI were published as Serial No. 2726, January, 1926, and those of District VIII as Serial No. 2745, April, 1926, of the Bureau of mines. The counties of Macoupin, Sangamon, and Montgomery, which are three of the principal coal-producing areas in the northern part of District VII, have been chosen for this report because these counties cover an entirely different part of the State than do the two districts already covered. Some leases in, Randolph and Washington counties are included as they are in the southern part of the district, and the data happened to be readily available.

Jan 1, 1926

By S. J. Hemberger, F. W. Lee

"This project constitutes the results of a geophysical field investigation undertaken in the mining areas in the vicinity of Marion, Crittenden County, Kentucky.Results were obtained at well-known mines being worked for fluorspar. Of special interest was the determination of mineral trends at such mines, particularly in relation to the fault patterns, because of ore in them.This work also constitutes a comparison between the field information that can be obtained by purely geological means and the additional information obtained by applying geophysical surveys to the same areas.As the mineralization in this area is controlled almost surely by the faults therein, the great importance of locating faults cannot be over emphasized. Accordingly, there has been incorporated herein the analyses as well as the application of electrical resistivity methods for fault determinations.In the western part of Kentucky, particularly in that area designated as the Cave-In-Rock quadrangle by the United States Geological Survey, is located the center of the fluorspar mining district of Kentucky. From the mining as well as commercial viewpoint, this area is of considerable interest and importance. It has been described by Currier4/ as a large structural dome that collapsed, through faulting, into a mosaic composed of a main fault pattern that has a strike to the northeast in sedimentary formations. Accompanying this main fault pattern are a large number of irregular faults. This fault complex is also traversed by a dike pattern that has a regional strike for this region focusing a northwesterly direction. The faulting occurred before the dike intrusions, the latter being composed largely of peridotite rocks. According to Reed,5/ most of the metallic mineralization, composed chiefly of galena and sphalerite, occurs at or near the Intersection of the dikes with the faults, indicating a possible igneous origin of the ore deposits. Reed adds that the fluorspar generally does not follow this rule but may also be found in other portions of the faulted zone not directly related to dike intrusions. The area may be considered of equal interest in the occurrence of lead and zinc and in the occurrence of fluorspar controlled by the faults. Hatmaker and Davis6/ give detailed information concerning the form of the ore bodies and economic factors that control ore production in this area; they also suggest the application of geophysical methods in this territory. Ulrich and Smith7/ also discuss geological details in this area. This area is therefore of interest, whether examined from a large structural point of view or from a very detailed angle. The former will assist in determining the origin of the mineralization and its economic possibilities, whereas the latter will give details concerning fault locations and their geologically and geophysically controlling features. This work was undertaken as a pilot investigation relating to the study of the location of fault occurrences, in which it was attempted to determine the location of faults as well as the fault patterns in certain isolated areas. No effort was made to identify the mineralization from the gouge material in the faulted zones; this problem was left for subsequent investigations."

Jun 1, 1946

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By M. Royker

Gold has been demonstrated as a possible catalyst for oxidation reactions. Some evidence for a possible promotion effect of platinum has also been recorded. The influence of platinum as promoter for Au/?-Al2O3 prepared via anionic ion-exchange for the oxidation of glycerol was investigated in a batch reactor at 60°C. It is inferred that the addition of platinum reduces the catalytic activity and therate of deactivation, resulting in an overall higher final conversion of glycerol with increasing platinum loading. The addition of platinum to the catalyst favours the formation of the desired product, glyceric acid.

Jan 1, 2012

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By McKay AD

The bulk of Australia's uranium resour- ces was delineated in the last 18 years when a total of $563 million (1984 dollar values) was spent on uranium exploration. Australia's share of the low-cost Reasonably Assured Re- sources in the World Outside the Centrally Planned Economies Area (WOCA) increased from 1.5% in 1967 to 29% by the end of 1984 and its share of the low-cost Estimated Additional Resources (Category I) then stood at 25%. As of December 1984, Australia's uranium resour- ces were estimated by the BMR to be: Cost range US$80/kg U (US$30/lb U301) Reasonably Assured Resources 463 000 t U Estimated Additional Resources(I) 251 000 t U Cost range US$80-130/kg U (US$30-50/lb U308) Reasonably Assured Resources 63 000 t U Estimated Additional Resources(I) 126 000 t U The increases in Australia's resources was sustained by a group of large and rela- tively high-grade deposits which were disco- vered during the period 1969 to 1975. Austra- lia's share of the low-cost resources was also enhanced by a contraction of WOCA's low-cost resource base due to escalation of production costs for smaller low-grade deposits. Most of Australia's uranium resources are contained in the Proterozoic unconformity- type deposits of the Alligator Rivers uranium field and the stratabound deposit at Olympic Dam on the Stuart Shelf. Most of the remain- der of Australia's uranium resources is con- tained in calcrete-type deposits. Less than 10% of Australia's uranium resources are in sandstone-type deposits. Total Australian production to the end of 1984 amounted to 26 241 t U, representing 3.4% of WOCA's cumulative production. Aus- tralia's share of WOCA's annual production has steadily increased from 1.3% in 1977 to 11.2% in 1984 (4390 t U). The increases in Austra- lian production took place in the face of reductions of production in WOCA countries, principally the US, from a record level of 43 988 t U in 1980 to about 39 000 t U in 1984. New low-cost production centres, mainly in Australia and Canada, have partly compen- sated the decline in US production. The Department of Resources and Energy (1985) reported that Australian exports of yellowcake are expected to reach 10 000 t U308 (8480 t U) by 1993/94, representing an in- crease of about 13% oer annum.

Jan 1, 1986

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017