Search Documents

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Jerry Chambers, Scott Crabtree, Randy Wheeler

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above.

Jan 1, 2006

By Luis Vassallo

El presente trabajo señala los beneficios que pueden obtenerse de la adopción inteligente de una estrategia de colaboración electrónica que responda a las necesidades de este segmento y que proporcione soluciones de verdadero valor agregado. Así, el modelo monolítico que prevaleció por muchos años, donde cada empresa era propietaria de las licencias mineras, operadora, mantenedora, contratista, vendedora, embarcadora y financiera, está desapareciendo. En la cadena de valor del proceso minero intervienen más empresas, contribuyendo valores agregados específicos y especializando funciones. Este cambio demanda mayores flexibilidades de los sistemas de información que deben ser totalmente abiertos, y permitir el intercambio instantáneo de información que facilite reaccionar oportunamente a las diferentes variables de la operación. Por ello, la colaboración electrónica permite a la minería adaptarse a un mundo que está cambiando.

Aug 25, 2002

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By John Kazakoff, Andrew Mortimore

"Production at the remote Kumtor Gold Mine in Kyrgyzstan commenced on schedule in December 1996.The ore mined during the first few months of 1997 from the upper benches of the pit did not produce the results predicted by the feasibility study. Low metallurgical recoveries experienced at the time were cause for great concern.It soon became clear the recovery difficulties centred around the preg robbing nature of the ore.Procedures were developed to selectively stockpile highly carbonaceous low recovery ore types. Testing methods were developed in the mill to quante the preg robbing activity of the ore. Preg robbing masking agents were added to the process to reduce the preg robbing activity of the ore.The importance of coconut carbon activity relative to the preg robbing activity of the ore was realized. Every aspect of the performance of coconut carbon in circuit was evaluated and optimized to improve carbon activity.Mineralogical analyses were completed defining the deportment of gold in ore and process tailingsBy year end the recovery difficulties had been overcome and plant design production had been achieved. Process improvements continue through 1998."

Jan 1, 1999

By Akihiro Higashide, Roy H. Patten

The DOT Tunneling method combines two conventional earth pressure balance shield machines in an overlapping cylindrical arrangement. The method allows two tunnels to be driven simultaneously with mini¬mum cross sectional area. Two full size trials, one configured horizontally and one vertically stacked, were successfully completed employing the DOT method. The method was then utilized for the new transportation system. The goggle-shaped DOT machine, 9.36 m high by 15.86 m wide, is the largest earth pressure balance shield machine in the world. This paper includes a general description of the DOT tunneling method as well as a history of its development.

Jan 1, 1995

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By G. M. Brownell

THE Falcon Lake stock is a small igneous mass, 2.6 square miles in area, which has intruded a belt of older lavas and metamorphosed sediments. It is well exposed and the entire area of its outcrop is taken up with surveyed mining claims, the claim lines forming a grid which makes ideal conditions for a detailed petrographical study of the unusual variations which are found in the composition of this unit (see Figure 1). The study of this mass, which has revealed features of both scientific and economic significance, began in the summer of 1939 when trainees in a Prospectors' Training Camp, a Do-minion-Provincial youth-training project under the writer's supervision, were, detailed to map rock outcrops on various mining claims. Microscopic study of rock specimens taken on a line across this stock were made during the following winter and proved to be of such interest that a special trip was made the following summer for the purpose of gathering more data, the results of which are presented here. Location The stock is close to the southeast corner of the province of Manitoba, about three miles from the Ontario boundary. It lies between Falcon and West Hawk lakes and less than a mile south of the Trans-Canada highway. It is easily accessible by motor car, as a branch road from the highway leads to the Sunbeam Kirkland gold mine, which is within the inner core of the stock. Previous Work This area was the first in the Province to receive attention from prospectors, who entered it from the adjacent Lake of the Woods district during the days of the mining boom in the 1890's. Small occurrences of gold, copper, molybdenum, and tungsten ores were found, but to date there has been no production from the district, except for small shipments of gold ore. The regional geology has been mapped by the Manitoba Department of Mines and Natural Resources, the Falcon Lake stock being shown and recorded as of "varying composition". The more detailed work involved in preparing the accompanying map has necessitated only minor changes in the outline as previously mapped.

Jan 1, 1941

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

Organization Place - Date 1918 American Iron and Steel Institute New York, N. Y. May American Water Works Association :.. St. Paul, Minn. May 20-25 American Institute of Chemical Engineers Berlin, N. H.. June 19-22 American Concrete Institute Atlantic City, N. J. June 24-26 American Society for Testing Materials Atlantic City, N. J. June 25-28 New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. 9-13 National Exposition of Chemical Industries New York, N.Y.. Sept.23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic' City, N. J. Sept.

Jan 5, 1918

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

By Arthur A. Cole

Although the metal silver has been known and prized from very ancient times, it is in the New World that the greatest silver camps have been found. This is shown in the following comparison: [] For the last few years, the World's annual production of silver has averaged about 240 million ounces troy. Of this total, the North American Continent contributes approximately three quarters, Mexico leading with 38 per cent, followed by the United States with 27 per cent, and Canada with nearly 9 per cent.[] Of the largest silver producers in Canada, the Sullivan takes first place. Although primarily famous as a lead and zinc mine, it produced, in 1926, more than 4.5 million ounces of silver. The Premier mine, in northern British Columbia, produced more than 3 million ounces. In Ontario, the largest producers in 1926 were the Nipissing mine, .with 1.9 million ounces, and the Keeley mine, with 1. 7 million ounces. The Mining Corporation produced 1.1 million ounces from mines in the Cobalt district proper, and an equal amount in South Lorrain; while from the Castle-Trethewey mine, in Gowganda, there was an output of slightly less than one million ounces.

Jan 1, 1927

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014