Search Documents

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By R. S. Dean

This report, the third of a series of annual reports of the Metallurgical Division to be released in this form, covers the fiscal year July 1, 1936, to June 30, 1937. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By W. H. Ryback

When a fire or explosion occurs in an underground coal mine, the atmosphere guickly becomes irrespirable. Highly irritant smoke and toxic levels of carbon monoxide and dioxide are produced, and consumption of oxygen by the fire or blast can reduce its concentration below that needed to support life. Work parties entering such a hazardous atmosphere for rescue or recovery operations are required to use, as their primary respiratory protection, a fully self-contained breathing apparatus of at least two hours duration. Apparatus used in this role has primarily been of the closed circuit rebreather type, using pressurized oxygen storage and chemical removal of expired carbon dioxide. Typically, commercial self-contained breathing devices for mine rescue have been heavy, bulky, and uncomfortable to use. The McCaa apparatus, long the industry standard, represented the best art available when it was First designed in 1926. It weighs 41 Ibs., protrudes about six inches above shoulder height, and provides breathing gas at temperatures up to 120° F. More recent designs, such as the Drager BG174A and Scott Rescue-Pak, using modern light weight materials and fabrication techniques have improved on all parameters of the McCaa to some extent. It was the intent of the Bureau of Mines, acting under the authority of the Coal Mine Health and Safety Act of 1969, to fund the development of a new self-contained breathing apparatus which would incorporate the best available technology and serve as a benchmark for future commercial designs, as the Bureau-sponsored McCaa had 45 years previously.

Jan 1, 1974

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By J. R. Nettle

The development of a process for upgrading offgrade titanium metal by electrorefining in molten salt led to an investigation of the electrotransfer characteristics of selected metals when alloyed with the titanium to be refined. Previous tests on seven binary titanium alloys showed that the degree of transfer of the alloying constituent depends on the constituent and on the operating procedurese.5 This report describes tests on electrorefining ternary mixtures of titanium with selected metallic elements. Ten alloys were prepared from high purity titanium and 2-1/2 percent of each of the metal pairs selected from the same elements used in the binary study; manganese, vanadium, chromium, zirconium, tin, molybdenum, aluminum. Operating variables were similar to those investigated in the binary alloy study that gave minimum alloy metal transfer. The data presented indicate the transfer characteristics of the various metals and combinations tested relative to each other.

Jan 1, 1962

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By O. Naiker, T. Riley

Keywords: Pyrometallurgy, furnace, Xstrata, ferrochromium, Premus Technology The presentation will give a basic overview of Xstrata Alloys. Included will be a brief history of the Alloys division as well as of each plant within the division. The Xstrata chrome plants utilise a wide variety of production processes, including Xstrata's Premus process, the Outokumpu process, and the conventional process. Xstrata?s Lion Project is underway, with commissioning expected in the third quarter of 2006. The new smelter will utilize Xstrata?s patented Premus process, and the competitiveness of the Premus process is discussed.

Jan 1, 2006

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Ray Mason, Damien Label, Howard Bernier, Kevin McDermott, Kevin Coombs

"GeneralWabush Mines is an unincorporated joint venture of seven steel companies and Pickands Mather & Co. The mining and concentrating facilities are located in southwestern Labrador and the pelletizing and shiploading facilities are at Pointe Noire, 200 miles south, near the town of Sept-lies.The operation is based on a 5 ½ sq. mi. specular hematite deposit with a reserve of 375 million tons of concentrate. Annual production capacity is rated at 6 million tons of pellets per year. The final upgrading process utilizes high-tension separation of silica following wet autogenous grinding, spiral gravity separation and fluo-solids drying. The concentrate is railed in closed cars to Pointe Noire. The concentrate is reground dry and pelletized on Dravo Lurgi travelling grate machines to produce an oxide pellet with 65.5% Fe, 3.0% Si02, 1.95% Mn and 93.5% Tumble Index.HistoryPlant operations commenced in 1965 with a concentrator capacity of 5.3 million tons per year and a pelletizing capacity of 4.8 million tons per year. The original facilities for classifying the crude ore into fine and coarse fractions for storage purposes before reblending as autogenous mill feed were found to be unnecessary and were by-passed after plant startup. Capacity of the operation was increased to 6.0 million tons of pellets per year in 1968. This increased capacity required the installation of an additional160 cleaner spirals in the ore dressing plant, a new 5000 hp ball mill, three balling circuits and increased cooling air capacity in the pellet plant.In 1970, the regrind circuit in the pellet plant was converted to dry grinding and a significant reduction in grinding media consumption and maintenance costs was realized. A ninth grinding mill of 5000 hp capacity was installed to compensate for the reduced capacity in going from wet to dry grinding."

Jan 1, 2000

By B. P. Faulkner

In 1974, Allis-Chalmers, in corporation with several iron ore operating companies, began to evaluate direct firing of coal in the GRATE-KILN System. Several coals were ground at the Allis-Chalmers Process Research and Test Center and shipped to Cleveland Cliff's pilot plant near Negaunee, Michigan, where they were used as fuel to pelletize Empire magnetite concentrates in the CCI pilot-scale grate kiln. Pilot plant tests were sufficiently favorable to warrant testing in a commercial-scale pelletizing plant. These tests were conducted at the Empire Mine in the late summer and fall of 1974 and again in the summer and early fall of 1975. In the fall of 1975, Allis-Chalmers Mining Systems Division started a program, in the Advanced Technology Center, designed to develop a laboratory test procedure for the evaluation and study of various parameters associated with the direct firing of coals in a GRATE-KILN System. The initial results of this program were presented at the 50th Annual Meeting Minnesota Section, AIME, January, 1977. This paper will briefly review the initial laboratory work and discuss the latest results obtained.

Jan 1, 1977