Search Documents

By Tian Li

Molecular crystal growth during gibbsite precipitation from caustic aluminate solutions under different flow regimes was investigated in three different laboratory precipitators. The gibbsite precipitation experiments were conducted at the same temperature, initial liquor composition and seed type. The Taylor-Couette precipitator and the stirred tank precipitator were operated, respectively, under the laminar and turbulent flow regimes, while the bottle roller precipitator was operated in a complex flow regime, where fluid flows are generated by the end-over-end rotation of the bottles. Comparison of the growth rate estimates from the different flow regimes showed good agreement, which suggests that the hydrodynamic regime has little or no effect on gibbsite crystal growth under the operating conditions employed in this work. The growth rate estimates from the current precipitation study showed a second order dependency on supersaturation and is consistent with a screw dislocation growth mechanism. The findings of the current work are in agreement with previous gibbsite crystal growth studies published in the literature.

Jan 1, 2003

By R. J. Chesher, J. C. Anzalone, T. F. Krusmark

The BHP Copper Refinery at San Manuel, AZ employs conventional electro-refining technology, plating at a current density of 335 A/m2 on six kilogram copper starter sheets. In 1995, a combination of variable anode chemistries and increasing current density in the tankhouse created periods of increased bismuth in cathode. Bismuth in electrolyte was minimized by bleeding electrolyte to the nearby BHP leaching facility. However, the expected drop in cathode bismuth was not achieved. Investigations indicated that starter sheets contained a significant concentration of bismuth. The bismuth was found to occur in combination with antimony on the surface of the sheet adjacent to the mother blank. Studies were conducted to determine the mechanism by which Group VB elements are incorporated into the starte sheets. Operational practices were introduced to minimize bismuth in starter sheets and improve cathode quality.

Jan 1, 1997

By Tanm Engin, Ali Riza Tarakcilar, Derya Dispinar

"Nowadays, the casting industry is developing parallel with the information technologies (IT). Particularly the casting simulation software is being frequently used in foundry floors for casting quality control and optimisation. In this study, the filling and solidification analysis of a rolling roll manufactured by spherical graphite cast iron were carried out by Vulcan casting simulation software. The appropriate defect relieving suggestions were presented by anticipation of defects that may form during the casting process.IntroductionThe optimisation of a casting process has long been the most focused area in manufacturing plants. Many of the work involve not only the process itself but the cost as well. When it comes to the process, it is important to be able to control the defects that may form during casting.The casting process begins with the melting of a charge; followed by pouring into the mould cavity. One of the most important factors is the difference in the liquid/solid density which may lead to porosity. On the other hand, turbulence during filling is another significant factor in casting operations [1].During solidification, due to the density difference between liquid and solid, porosity might form which leads to crack-like defects. There are several other factors that may determine the quality of a casting such as segregation, inclusions, grain size and etc. However, porosity is one of the first parameters that can be easily determine and controlled by the help of simulation software. Simulation is a cost-effective tool in the optimization of process parameters and castings can be visually observed. Time loss and economic expenses could be minimized [2]."

Jan 1, 2012

By Ibrahim Yusufoglu, Ahmet Orkun Kalpakli, Cem Kahruman, Sedat Ilhan

"The effects of oxalic acid concentration, temperature, stirring rate and particle size on the dissolution rate of synthetically prepared calcium molybdate were investigated. Dissolution of calcium molybdate in oxalic acid solutions takes place as a series - parallel type reaction. In the first reaction step, which proceeds according to the ""Langmuir - Hinshelwood Mechanism"", calcium aqua oxalato molybdate is formed as a complex chelate intermediate product. In the second reaction step, molybdic acid is formed during the slow hydrolysis of calcium aqua oxalato molybdate, and it reacts rapidly with oxalic acid to form the polymeric hydrogen oxalate dimolybdate chelate as an end product. Activation energies were calculated as 41.4 and 49.9 kJ mol-1 for the first and zero order reactions. The fractional conversion versus time relationship can be given by the following equation.IntroductionMolybdenum is used widely in electric-electronic, metal working, aerospace and aeronautic, nuclear, glass and petrochemical industries because of its high melting temperature and resistance against chemical effects. However, the largest molybdenum consumers are the iron-steel and super alloy industries where molybdenum is used as an alloying element. Industrially important molybdenum minerals are limited to molybdenite (M0S2), powellite (CaMo04) and wulfenite (PbMo04), which are considered as primary molybdenum resources. Secondary molybdenum resources are spent catalysts and scrap [1-4].Molybdenum has been produced by pyrometallurgical processes in the past. Since it is possible to process low grade molybdenum ores and industrial wastes by hydrometallurgical processes, which are more environmentally friendly than pyrometallurgical processes, the importance of the use of hydrometallurgical processes has increased in the molybdenum production industry."

Jan 1, 2012

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By Alicia Esther Ares, Carlos Enrique Schvezov, Alejandra Silvina Roman, Claudia Marcela Méndez

In this paper the structure of aluminum based alloys and their corrosion behavior by using different electrochemical techniques as characterization methods are considered. Currently, it becomes imperative to know the role of the Al2Cu against the susceptibility to corrosion of these alloys. The present work aims to studying the electrochemical behavior of aluminum base alloys with the following compositions: Al-1wt.%Cu, Al-4.5wt.%Cu and Al-15wt.%Cu (with different grain structures), in 1M NaCl solutions, at room temperature. Cyclic potentiodynamic polarization tests were performed and were found that the alloys with more than 1wt.%Cu in the matrix have an unstable behavior and without tendency to reach passivity. The equivalent circuits derived from electrochemical impedance spectroscopy technique (EIS) generally showed two capacitive contributions. The susceptibility to corrosion becomes a complex function, not only of copper concentration and structure, but also with interdendritic spacings and distribution of phases in the alloys.

Jan 1, 2015

By Xuewei Lv, Maojun Zhou, Xiaobo Huang, Rende Zhang

"The characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. In this study, an evaluation of the roughness of the iron ore particles, with the measurements of size distribution and the measurements of specific surface area with the liquid nitrogen absorption, was developed. The main theory of this method is the fact that the roughness of the particle influences the specific surface area apparently. The specific surface area of the particles can be measured with the laser diffraction method and the liquid nitrogen absorption method. The influence of the surface roughness of the particle can be measured with the nitrogen absorption and cannot be measured with the laser diffraction. Therefore, the roughness can be got by comparing the specific surface area with two measurement methods.IntroductionThe characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. There are three main methods for measuring the size distribution of mineral particles: sieving, laser diffraction, and sedimentationl). Many techniques involve sedimentation such as the Horiba2, 3) and the Cyclo-sizer1). In the mineral industry, size distribution is usually determined by sieving because it can be carried out accurately for all particle sizes larger than 45 . The preferred method to obtain the size distribution of finer particles is laser diffractometry. The technique has several advantages: it produces measurements in a few minutes with considerably less labor compared with the cyclo-sizer and for a range of sizes considerably wider in comparison with the sedigraph4). The equivalent-sphere size distribution reported by laser diffractometry is valid for metallurgical calculations and can be routinely used in mineral processing plants. The surface area of the particles can be measured by the BET method of nitrogen adsorption, or it can be calculated from the size distribution. However, the latter calculation requires the size distribution to be accurately known across the whole size range, and assumptions have to be made about the shapes and surface roughness of the particles and presence or absence of pores (see below). The BET method is based on the physical adsorption of gas over the whole exposed surface area and measures the surface area stemming from the roughness and open pores on the surface of the particle5). The calculation of the surface area from the size distribution is usually based on the assumption that all the particles are smooth spheres, without considering the shape and/or roughness of the particles. Determining the surface roughness of the particle with these methods, is the objective of this study."

Jan 1, 2012

By M. Sripathy, K. V. Sharmal

"The conventional fiber reinforced plastic does not participate in the plastic deformation or enter the large plastic deformation state during collision. On the other hand, sandwich structure allows more plastic deformation, which improves the energy absorption efficiency. The objective of this study is focused on the investigation of the crushing of sandwich structure made from sisal / coir / bamboo/ glass fabrics as reinforcement and with polyester resin to form the composites skin and with polyurethane foam as the core. Experiments were conducted, showing that the underlying crushing mechanism of sandwich structures is very different from that of solid-section thin-walled structures. When a sandwich is subjected to crushing, the core deforms in the shear mode and the face bends independently. The damage is through the width zone of crushed foam core accompanied by a residual crushing in the foam. It is shown that such damage causes a significant reduction of compressive strength. Results show that glass/polyester and bamboo/polyester skin based sandwich structures have superior compressive strength. Coir /polyester based sandwich structure come next to glass/polyester sandwich structures in this aspect which is then followed by Sisal /polyester based sandwich structures.IntroductionCellular polymeric foam sandwich structures are often employed in shock mitigating applications. The cellular polymeric foam has several favorable properties, such as, low density, relatively high strength-to weight ratio and a significant degree of crushability. This high crushability is the result of the large void ratio in such materials, which also facilitates the collapse of cell walls via bending and buckling [1]. A few feasibility studies on FRP sandwich panels show that the panels efficiently provided high mechanical performance for minimum weight [2]."

Jan 1, 2012

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By R. Escalera-Lozano, M. Herrera-Trejo, M. A. Pech-Canul, J. López-Cuevas, A. L. Leal-Cruz, M. I. Pech-Canul

"The use fly-ash (FA) and rice-hull-ash (RHA) offers the potential for the manufacture of hybrid Al/SiCp/spinel composites via reactive infiltration, both with recycled aluminum. The main reason behind this statement is the beneficial role that both waste materials play in preventing the degradation of SiCp reinforcements when the composites are processed with aluminum in molten state. Experimentally, MgAl2O4 is formed in situ during the infiltration of SiCp-preforms in the temperature range 1050-1150 oC for 50-70 min in argon atmosphere at a pressure slightly above to that of the atmospheric pressure. Results reveal that both FA and RHA help in preventing SiCp dissolution and the subsequent formation of the unwanted Al4C3; and although FA-composites still might be susceptible to corrosion via Al4C3 -by the interaction of native carbon in FA with liquid aluminum- a proper FA treatment significantly mitigates its deleterious effect. Primary corrosion mechanisms and strategies to overcome the potential degradation effects are outlined.IntroductionOwing to inherent materials characteristics and post-processing complications –such as corrosion damage- development of metal matrix composites (MMCs) from recycling/waste sources might be a challenging task. Fly-ash (FA) and rice-hull-ash (RHA) are two primary waste materials that offer excellent opportunities for the development of Al matrix composites. Due to its singular hollow-spherical shape and low density, FA has attracted the attention of many researchers. For this reason, most of the efforts to develop Al-based composites from waste materials have been centered on the use of fly ash. Extensive research efforts in the use of FA for Al-based composites have been undertaken by Rohatgi and coworkers [1-4]. In addition to lowering costs, incorporation of fly ash into aluminum has been proved to decrease the materials’ density, increase their hardness, abrasion resistance and stiffness [1]. One of the major outcomes from the mechanical evaluation of aluminum composites prepared with fly ash is that related to their compression characteristics. Typical compressive stress-strain curves form A356/hollow fly ash composites show a linear elastic region followed by a plateau (associated to the collapse of the hollow particles), and then an increase in stress, representing densification of the foam. The crushing of the cenospheres in the composites has been related to an enhancement in the energy absorption capabilities of the material and to a better damage tolerance [4]."

Jan 1, 2008

By Leszek Blacha

Since several years aog there is noted an increasing importance of the metallurgical vacuum technologies. This refers mainly to the extra furnace steel treatment processes, melting of steel and special alloys in the induction and arc vacuum furnaces, as well as refining processes of nonferrous metals. In the presented work, there is discussed a phenomenon of evaporation of volatile components of metal bath under reduced pressure with description of kinetics of this process. In this article are presented are the evaluation of the mass transfer coefficients in the melt and gaseous phase. Based on results of our own research on removal rate of impurities from liquid copper (bismuth, lead) in vacuum refining process, it is determined the thickness of hypothetical boundary layer in the gas phase. This allowed to formulate a general kinetic equation defining the evaporation rate of gaseous components from metal bath. The values of mass transfer coefficients determined from this equation were compared with experimental results by other authors working on the evaporation effect of melt components of metal alloys.

Jan 1, 2006

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By John Snowberger III, J. Brent Hiskey

The electrochemical dissolution of super alloys containing different amounts of rhenium was investigated. The initial part of the investigation focused on the anodic dissolution of rhenium from second-generation (3% Re) and third-generation (6% Re) nickel based alloys. Exploratory electrochemical tests were conducted to evaluate solution chemistries and to establish fundamental dissolution behavior of the alloys. These included rotating disc electrode (RDE) cyclic voltammetry, linear sweep voltammetry, and chronoamperometry tests. Electrolytes comprising sulfuric acid, hydrochloric acid, and ammonium sulfate were examined. Of these, a 0.1 M HCl solution proved to be extremely effective for electrochemical dissolution of samples of CMSX-4, CMSX-10, and SC-180 alloys. This paper discusses in detail the electrochemical behavior of these alloys.

Jan 1, 2014

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By Baokuan Li, Fang Wang, Meilong Shan

"As the advantage of uniform bus loading, the electroslag remelting (ESR) furnaces with three - phase installation by delta or star connection are mainly used to produce the large or super large ingot. The electrical efficiency is significantly improved as the short circuiting through the molten slag. However, little is found about fiindamental research on the electromagnetic field of the ESR system with three -phase installation. A three-dimensional (3D) finite element model was developed to simulate the current density, magnetic field, electromagnetic force and Joule heating for a system of electrode, slag and ingot in the ESR system with three -phase installation.IntroductionThe metallurgical performance of the ingot is the fundament and precondition to obtain the large forging of high quality, which has a critical role in the producing of forging. The electroslag process (ESR) to product the metal materials of high homogenization and clarity become more and more popular[1].The electroslag process is a special smelting technology of producing small ingots, which originate in 1950[2].At present the three, four or six electrode is used in large scale electroslag furnace. It has been found that the deeper molten pool and the wider of the two-phase zone with only one large diameter of electrode to product large ingot effect the solidification microstructure of ingot[3]. However, the molten pool becomes shallow relatively with several electrodes producing the large ingot, which is benefit to the solidification microstructure of ingot. Three electrodes electroslag remelting furnace take the three phase equilibrium power supply to making the load and electric power network balance, avoiding the distortion phenomenon induced by single phase power supply and saving electric power. It also can uniformize the distribution of heat source."

Jan 1, 2012

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By Wan Pu

Chrysotile asbestos samples from different mines have been studied by SEM and TEM, including high resolution electron microscopy, to find reasons for differences in physical properties of different types of asbestos fibres. The results show that the inner diameters of fibre tubes and the lattice images of fibres are different for soft and hard asbestos fibres. These differences are related to temperatures and geochemical conditions during the growth of chrysotile asbestos.

Jan 1, 1989

By V. Bredykhin

The efficiency of scrap processing depends firstly on reliability of information about its chemical composition. The paper presents the results of the investigation and development regarding solid copper alloy scrap in the range of lump size 40÷300 mm. Nowadays the sorting of lump scrap is done by two methods: 1. Sorting according to metals and alloys is done at places of scrap generation, and further till metallurgical processing each lot has its "certificate"; 2. Hand sorting of scrap is done according to the marks on solid items in special shops using proximate analyzers or manually by experienced workers. This sorting process is labor - consuming low efficient and involves mistakes. The informational method is a promising trend in the copper scrap sorting. The method is direct, i.e. as a result of sorting the chemical composition of each scrap lump or main elements is determined, and assured data of qualitative and quantitative composition are received.

Jan 1, 2006

By Sheng-hai Yang

The electrochemical synthesis was conducted in anhydrous ethanol solvent mixed with conductive reagent when tantalum plate was used as anode and stainless steel plate as cathode. The effects of different conductive reagents (such as NH4Br, (CH3)4NCl, (C4H9)4NCl), conductive reagent concentration and the space on the cell voltage and the current density were investigated. The current efficiency of electrosynthesis was more than 95%. The electrolyte, a mixed solution was then undergone air distillation and vacuum distillation to get the final product which was characterized by Fourier Transform Infrared(FTIR) spectroscopy, Raman spectra, 1H-Neclear Magnetic Resonance(1H-NMR) spectroscopy. Carbon and hydrogen contents in the product were determined by elemental analysis instrument. Results consistently show that the product was tantalum penta-ethoxide.

Jan 1, 2006