Search Documents

By M. R. Dahm

The demand for low sulfur steel by steel manufacturers and their customers has been steadily increasing for 25 years. Historically sulfur has been controlled by various means and with various additives but lime-magnesium external desulfurization of hot metal has become established as the dominant method in North America today. Magnesium powder produced from primary magnesium ingot has been the major source or raw material. However, periodic increases in the price of this commodity have encouraged producers to look to secondary magnesium for an alternate source of magnesium. Secondary magnesium from post-consumer scrap can be cleaned, sized, and prepared to produce a high quality magnesium reagent for use in hot metal desulfurization at a lower cost than material processed from primary ingot.

Jan 1, 2000

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By A. P. Paiva

Studies focused on the recovery of precious metals by solvent extraction have recently increased. either to devise suitable solvents or to clarify the involved extraction mechanisms and kinetics. In this work, a comparison of the performance exhibited by triphenylphosphine (TPP), bis-(penty1thio)-ethane (BPTE) and triisobutylphosphine sulfide CI"I'BPS) in the extraction of silver from acidic chloride media is carried out. Extraction and stripping isotherms involving the three extractants are presented together with the results obtained on the selectivity of silver extraction against high contents of iron, copper and lead. Attempts to clarify the mechanism of silver extraction by TIBPS were performed by studying the distribution coefficient dependence on ligand and chloride concentrations. The effect of temperature on extraction and stripping is also considered. The interfacial tension for the system, measured with different concentrations of extractant in the organic phase, is analysed.

Jan 1, 1994

By D. Maurice, W. D. Riley, J. A. Hawk

"The increased penetration of wrought aluminum into the automotive market is stimulating a need to separate wrought aluminum from cast aluminum because of: a) the additional value of scrap wrought alloys and b) the increase in the total amount of aluminum automotive scrap will outstrip the demands of secondary aluminum foundry industry. The availability of clean fractions of wrought and cast aluminum and incidentally, a clean cast magnesium fraction will allow increased recycling of aluminum used in the automotive industry.Hot crushing has been tested previously and proposed as a means to separate cast from wrought alunrinum product. The underlying concept is that when a mixture of cast and wrought aluminum is thermally processed and then subjected to crushing action, differences in toughness between wrought and cast aluminum alloys will become more pronounced. Hence, it should be possible for conditions can be established such that the cast material fragments, while the wrought material, having lost much less of its toughness, merely deforms. The two types of product could then be separated by simple sizing methods.In this paper we report on the testing of this concept. We were unable to replicate the results which originally demonstrated proof of concept. Possible reasons for this are discussed, as well as the possibility that the original results may not be as desirable as the current results for subsequent sorting."

Jan 1, 2000

By F. G. Caballero, J. L. Gonzalez-Carrasco, S. Barrius, H. Carreon, M. Lieblich

"The grit blasting is a low-cost technique successfully used to enhance mechanical fixation of the implants through increasing their roughness. As a result of the severe plastic surface deformation, it produces subsurface effects such as grain refinement, hardening and compressive residual stresses which are generally evaluated with destructive techniques. In this research work, non-contacting and contacting thermoelectric power measurements are performed in blasted 316L VM and Ti-6AI-4V specimens using Ah03 and Zr02 particles which yield a coarse and a fine rough surface, respectively. This study correlates the microstructural changes induced by the grit blasting treatment and the limitations and advantages of each of the nondestructive thermoelectric techniques based on the Seebeck effect used to evaluate these biomaterials.IntroductionIt is well known that surface properties play an important role in metallic materials used in bio-medical applications. Since the biological response is correlated directly with surface properties it is comprehensible the intense activity in superficial modification by physics or chemistry methods in this field. Grit blasting, one of the most popular surface modification of metallic biomaterials, enhances the mechanical fixation of the implant through the increase in roughness [1-3]. Roughening is developed by bombarding the surface with a high-velocity jet of ceramic particles, being the final roughness a function of the processing parameters (pressure, distance, time, ... ) and blasting particles (nature, shape, size). As the plastically deformed surface layer tries to expand relatively to the intact interior of the specimen, residual compressive stress gradients develops perpendicular to the surface at shallow depths with a maximum value at a depth in the range of 5 to 60 µm. This surface treatment also may cause subtle variations in the subsurface material properties, such as increased hardness and grain size refinement, which are consequences of the significant plastic deformation through cold work. Blasted affected zones may extend to a depth of up to about 200 µm. The subsurface hardening and the near-surface compressive stress gradient playa beneficial role by retarding fatigue crack nucleation and further growth, ultimately extending the fatigue life of the metallic part [4]. In this work, two non-destructive thermoelectric techniques (NDTT), the non-contacting and contacting thermoelectric power measurements were used to analyze the subsurface induced changes on blasted Ti-6AI-4V and 316L VM specimens using Al2O3 and Zr02 particles. Detailed information on the microstructural induced effects and subsurface mechanical properties were published elsewhere [5-8]. Here the nondestructive evaluation of the involved microstructural changes is used to assess the global subsurface damage. Advantages of using nondestructive techniques during manufacturing are envisaged."

Jan 1, 2012

By Björn Hinzel, Joachim Rösler

"The most important characteristic of open-pored metals is porosity, since it enables all of their functional applications as filters or sound absorbers. Due to the notch effect of the pores, mechanical properties of porous metals are better than the ones of comparable structures made of polymers or ceramics. Consequently, only open-pored metals can be used in aircrafts to reduce flow noise or noise resulting from the core engine by acoustic absorption. Absorption properties depend highly on pore size and porosity of the material, which must be characterized as precisely as possible in order to analyze the correlation between morphology and noise reduction performance. Here, a line segmenting method is explained in order to characterize pore size and porosity of absorber materials using image processing based on two dimensional microscopy images, including sample preparation and specification of the set-up. Then, the influence of the pore structure on the measured absorption behavior is discussed. Finally, the correlation of acoustic behavior, pore morphology, and porosity is outlined.IntroductionSignificant noise loads affect everyone causing anxiety, depression, insomnia and other effects which impair health and productivity [1],[2]. Due to the rising number of flights and aircrafts, air traffic noise increases dramatically. To counter this development, various approaches have been developed to reduce the different noise sources resulting from airframe, jet or engine [3],[4],[5],[6]. One approach to reduce this noise is the application of noise reducing liners in the hot gas path [7]. This is especially important, since the engine is becoming the dominant noise source of modern airplanes during take-off [8]. Due to the elevated temperatures and high fatigue loading in this part of the aero-engine, conventional passive absorber materials cannot be used. Polymers would not be able to bear the heat and ceramic fibers would crack under the mechanical loading due to the notch effect. Consequently, this study focuses on metals with open pores, which can resist elevated temperatures and fatigue loading and additionally resemble geometrically conventional passive absorbers. Based on the production processes, e.g. sintering of metal fibers [7], powder processing using a foaming agent [9], coating of polymer foams [10], or using melt infiltration techniques [11], the characteristic dimension of the porosity is usually in the range of 0.01-10mm. In this work, sintered metals and metal sponges are analyzed after the theory of sound absorption is briefly outlined. Then, measurements of the acoustic absorption of metal sponges and sintered metals in an impedance tube are performed. To understand and predict the acoustic properties of metals with open porosity, it is necessary to characterize the materials as precisely as possible. This is explained in detail using a line segmenting technique, followed by a discussion of the connection of pore characteristics and acoustic absorption. Finally, a conclusion is given."

Jan 1, 2012

By Claude Lorenson

"The Spyrometer™ imaging pyrometer brings new dimension of imaging capabilities to temperature measurement technology by combining a high temperature video camera with scanning optical pyrometry. This gives the operators the ability to observe process conditions while measuring the temperature of virtually any object or region in the field of view. Since the lens tube of the camera can be air or water cooled, it is possible to see inside furnaces giving a very good view of many different types of metallurgical processes. Specific benefits in process knowledge and maintenance tasks for furnaces in different types of metal industries are discussed.1-Principles of Imaging PyrometryLens tube, camera and processorImaging pyrometry is the combination of video imaging and computer-driven pyrometry that measures the temperature of certain zones (selected by the operator) within the image viewed on the monitor screen. To obtain a detailed image of the metallurgical process under observance, it is necessary to place the optical objective of the camera close to the process. The Spyrometer™ (which is Quadtek's tradename for its imaging pyrometer) objective is housed in a lens tube that is cooled and permits insertion inside the vessel of interest. The length of the lens tube is chosen on the basis of making sure that the tip of the tube is just beyond the refractories lining the inside of the furnace. In most pyrometallurgical processes, we have found that the most reliable system set-up uses a water cooled shroud to cool the lens tube optics. A sapphire window provides maximum protection from the environment. Even in the case of the water cooled version, there is an air purge for the lens that keeps the objective clean and protects against hot metal splashes."

Jan 1, 1997

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By Asmo Vartiainen

The viscosity of liquid Fe-O-SiO2 -slag at copper smelting conditions was investigated using a rotational viscometer. The studied parameters were oxygen partial pressure (10" °-10"6 bar ); composition of slag (Fe/SiO2 ratio), and temperature (1250-1400°C). The viscosity values are presented as a function of Fe/SiO2 ratio and as isoviscosity curves in ternary FeO-Fe2O3-SiO2 diagrams. The increase in viscosity at high silica contents can be accounted for the polymerisation effect of SiO4/4- -anions. At high ferric iron contents, higher oxygen partial pressure, the viscosity values increase especially near the magnetite saturation. The viscosity values are highest at the double saturation of silica and magnetite. At lower silica and ferric iron contents the viscosity values are more uniform in the homogenous liquid slag area. The viscosity values were lowest at high temperatures and highest at low temperatures.

Jan 1, 1998

By G. A. Irons, D. Guo

"The average spout height and width produced by bottom gas injection in a water model of a steel ladle were measured with an image processing technique. It was revealed that the spout height could be described by a Gaussian curve. A combined SIMPLE -VOF model was developed to simulate the liquid surface and flow. The results showed that, though the model produced reasonable velocity distributions and free surface positions, the spout height due to the dynamic head of the rising liquid was substantially lower than observed, indicating that the bubble dynamics at the bath surface play an important role in spout height.IntroductionDue to the enormous importance of gas injection and stirring in metallurgical processes, there have been numerous publications on water and numerical modeling of such vessels. The free surface of the bath has received considerably less attention, despite its importance. At the free surface there are often important chemical phenomena occurring that require a good understanding of the fluid flow; these would include reoxidation of steel, metal splash and fume formation. Furthermore, to understand the details of slag-metal interactions such as slag entrainment, metal losses to slag and the transport phenomena associated with refining reactions, it is necessary to understand the plume and spout interactions first.There have been few experimental studies of the free surface of liquid in gas-injected ladles [1- 3], and even fewer on numerical modeling. Brimacombe and co-workers [1] studied the gas void fraction in the spout region, using a double-tip electrical resistance probe. This sensor cannot distinguish between gas in bubbles about to break and gas in the freeboard. Thus, it is a matter of judgement as to the position of the free surface. Schwerdtfeger and co-workers [2] used a single probe configuration with a wire and a counter electrode in the liquid, so that the height of the continuous liquid phase was unambiguously determined. Irons and co-workers [3] measured the spout height by ultrasonic and electrical capacitance techniques. These techniques were as reliable as the resistance techniques, but were restricted to low flow rates."

Jan 1, 2001

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991

By Liping Gu, Gordon A. Irons

"A 1/3 scale ""thin-slice"" model of an electric arc furnace was developed so that gas could be injected to simulate foaming gas evolution. The influence of arc jets, oxygen lancing and bottom bubbling was also simulated. Liquid velocities were measured by a white light particle image velocimetry system. Numerical simulations of some of these effects were made using commercial CFD packages. Comparisons with measured results show that considerable care is required to select the appropriate model and to interpret the computational results.INTRODUCTIONDuring recent years electric arc furnaces (EAF) have captured a significant share of steel production, partially due to increased productivity through the introduction of advanced technology such as oxygen injection, slag foaming and long-arc operation, process automation and post-combustion. However, systematic analysis of the process and these effects on heat transfer and fluid flow in the furnace is still in its infancy. Most investigationsl1 6l have been restricted to a specific application such as oxygen lancing or bottom stirring. In addition, it is very difficult to make comparisons between these computed results and experimental/industrial results. In this work a 1/3-scale ""thin-slice"" model of Dofasco's 190 ton EAF was built. The fluid flow in the bath due to the arc jets, bottom stirring, oxygen lancing and CO evolution was simulated. The velocity distributions in the bath were measured using Particle Image Velocimetry (PIV) System. In addition, numerical simulations of bottom stirring and CO evolution were carried out using two commercial CFD packages (Fluent and Phoenics). The objective of this work is to validate the mathematical models so that they can be applied to the full-scale furnaces."

Jan 1, 1999

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By Jianhui Wu, Jing Zhan, Chuanfu Zhang, Zhijian Wang, Chu-ping Xia

"A novel technology about interactive roast of complex bismuth sulfide ore with low grade and Pyrolusite was put forward using the low-grade bismuth sulfide ore and pyrolusite as raw materials. The predominance diagram of Bi-Mn-S-O system was drawn by thermodynamic calculations. Stable coexistence area ofBizO3 and MnSO4 and its control condition was obtained. The interactive roast conditions including roasting temperature, roasting time, the ratio of n(MnO2)/n(S), ventilation rate and so on are investigated systematically. The results show that the sulfur-retained ratio reaches about 98%, in which formation rate of MnSO4 was 94.04%, most of the residual sulfur in the ore exist in the form of BhsO32(SO4)10 in the roasting products The optimum roasting conditions were as follows: roasting temperature of 650°C, roasting time of2h, 1.4 for n(MnO2)/n(S) and 140L/h for ventilation rate.IntroductionBismuth is a ""green"" rare metal with the characteristics of safe, nontoxic and low melting point[l].The use of bismuth and its oxides is extending from traditional fields such as pigment, fusible alloy, bismuth class of drugs and metallurgical additives to the high-tech fields such as semiconductor, high-temperature superconducting materials and nuclear power and so on. Bismuth is one of the precious advantageous resources in China which owns the most abundant bismuth resources in the world. Bismuth metallurgical process is divided into the pyrometallurgy and hydrometallurgy [2-4]. Hydrometallurgy for bismuth is mainly used for the processing oflow-grade complex bismuth ore, whose key steps are oxidative leaching process of the bismuth sulfide ore by strong oxidants(FeCb, Clz, HNO2 etc) in hydrochloric acid system. Therefore, the corrosion of strong oxidants, high demand for equipments and poor operating environment are its inherent disadvantages. Pyrometallurgy for bismuth is mainly used for the processing of high-grade bismuth raw materials or concentrate, which is the main method for bismuth metallurgy at present."

Jan 1, 2013

By Ken-ichiro Uemura

"The DIOS process has been developed for eight years since 1988. The research project was started with the element studies carried out by each of the five integrated steel making companies in Japan, the final two and half years were spent for the pilot plant studies. Operation were conducted in the entirely closed and pressurized system successfully as planned. From the result, the DIOS process was proved to be viable as a future iron-making process substitutable for the conventional blast furnace. In addition, a lot of findings were obtained. Hot metal productivity was primarily determined by a oxygen flow rate, and a coal consumption varied depending on the productivity. The post combustion ratio was a little lower than expected from the result of the element study. It was supposed to relate the gas-reforming with coal or volatile matter in the free space of the furnace. Hot metal carbon content seemed to depend on the char content in slag.INTRODUCTIONThe JISF's DIOS pilot plant (DIOS=Direct Iron Ore Smelting Reduction Process) has finished its last campaign of the operations in January 1996. The project was started in 1988 as a joint research of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation (JISF) with a subsidy for promoting coal productions and utilization technologies from the Agency of National Resources and Energy, the Ministry of International Trade and Industry(MITI). Throughout the pilot plant test, a total of over 20,000 tons of hot metal was produced for more than 2,000 hours of the operation. Recorded production rate was 538 ton/day for 3 days at a specific coal consumption of approx. 1,000kg/hmt. Long-term operation was carried out in the fifth campaign for 18 days, which has proved that the entirely closed and pressurized DIOS process works well as planned. In Figure 1 is shown the representative operational performance obtained in the first five campaigns. The project is going to be finished by the end of March this year after investigating the technical viability and economic potential of the process, and completing the conceptual design of the DIOS commercial plant. In this paper, the system and facilities of the DIOS process are first introduced and some of the results of the pilot plant test are detailed later."

Jan 1, 1996

By Deepak Malhotra

Rosario Dominicana, S.A., operates a gold processing complex at Pueblo Viejo, northwest of Santo Domingo (Dominican Republic). The plant processes approximately 10,000 mtpd of oxide gold-bearing ore with a work index of 11 kWh/mt. The ore hardness has increased to about 17 kWh/mt. Metallurgical auditing of the plant was conducted? to find ways to modify the circuit to process hard ore without sacrificing throughput. In addition, unit operations were optimized to increase recovery and reduce operating cost,. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1989

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By N. Kanari

The kinetics of oxychlorination of MgO by C12+02 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+02, C12 and 02 at 950 °C were about 0.65, 0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999