Search Documents

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By Nathalie Neveux

For the first time, dehydrated ferrous sulfate was successfully used for the dry synthesis of potassium ferrate. In addition, ferrate ion is stabilized as a solid solution where hexavalent iron is partially substituted by S(V1) leading to a sulfato-ferrate having the following formula K2(Fe,S)04. This substance has an efficient life time of about six months. Ferrate ion is a powerful oxidant ( EO = 2.2V ), a bactericidal agent and possesses coagulant, flocculant properties. Its reduction generates nascent oxygen, hydroxyl groups and Fe(OH)3. Alkali metal ferrate is probably the future global agent for water treatment. Applications of this material in the field of urban and industrial effluents treatment have been investigated. Heavy metals cations such as Cu, Cd, Mn, Ni, Pb, Zn, ... were successfully removed. The results of sulfato-ferrate use for cyanide destruction, decrease in COD, soil, discoloration of pulp and paper effluents will be summarized.

Jan 1, 1999

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By Robert Corson

Zinc has a large solubility in Fe and a completely filled ?d? shell. With the discovery of dramatic increase of the magnetostriction in Fe by Ga addition, an examination of element Zinc that is adjacent to Ga in the periodic table is of significant interest. In this work, the effect of binary alloying of Zn with Fe on the magnetic and magnetostrictive properties is examined. The FeZn alloys were processed using powder metallurgy and vapor phase synthesis, and Zn contents were varied from 5% to 30%. An examination of the influence of different processing parameters and the Zn content on the resulting alloy properties is presented. The alloys were characterized using X-ray diffraction and SEM. Magnetostriction measurements were carried out at different pre-stress levels. Magnetic properties were measured using a vibrating sample magnetometer.

Jan 1, 2006

By G. S. Rao

Levitated drops of Fe-18%Cr-2%C were reacted with oxygen-argon mixtures to study the reactions that occur in the AOD process, where the gases are injected into the melt and form bubbles. In the laboratory an argon-oxygen pulse, followed by pure argon, was flowed past the levitated drop to simulate the transient conditions in the gas phase as the bubbles rise in the melt. Oxide layers formed on the drops immediately when they came into contact with gas pulses containing 75% or more oxygen. Once the oxygen flow had ceased, the oxides reacted with the carbon in the drops to form CO gas and eventually disappeared. The de-carburization reaction occurred without oxide formation when the gas contained 50% oxygen or less. Melts that were sampled after EAF tapping, ready to be charged into the AOD, showed a higher tendency to oxide formation and consequent carbon boil than pure ternary Fe-18%Cr-2%C alloys made in the laboratory. The actual steel samples contained significant impurities, such as 0.25% Si and 0.56% Mn. A similar effect of oxide-forming impurities had been observed previously with binary Fe-C alloys. Movies were taken of the oxide formation and decomposition, and the results will be presented, along with data on the experimental conditions, including temperature and oxide compositions. The results are important because they give an insight into the reaction mechanisms in the AOD, which must be understood in order to improve and model the process.

Jan 1, 2006

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By K. Krishnapisharody

The phenomenon of slag droplet formation under the action of gas-stirring in steel ladles has been analyzed with experiments conducted in a thin-slice room-temperature model using water and mineral oils as the working fluids. Visual and video investigations have been performed on the interface behaviour along with measurements of liquid velocities in both phases, using the Particle Image Velocimetry (PIV) technique. The measured velocity data and observations on the interface break-up establish that the droplet formation results primarily from an instability mechanism at the interface.

Jan 1, 2008

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By S. M. McDeavitt

Waste form alloys are being developed at Argonne National Laboratory for the disposal of remnant metallic wastes from an electrometallurgical process developed to treat spent nuclear fuel. This metal waste form consists of the fuel cladding (stainless steel or Zircaloy), noble metal fission products (e.g., Ru, Pd, Mo and Tc), and other metallic wastes. The main constituents of the metal waste stream are the cladding hulls (85 to 90 wt%); using the hulls as the dominant alloying component minimizes the overall waste volume as compared to vitrification or metal encapsulation. Two nominal compositions for the waste form are being developed: (1) stainless steel-IS wt% zirconium for stainless steel-clad fuels and (2) zirconium-8 wt% stainless steel for Zircaloy-clad fuels. The noble metal fission products are the primary source of radiation in the metal waste form. However, inclusion of actinides in the metal waste form is being investigated as an option for interim or ultimate storage. Simulated waste form alloys were prepared and analyzed to determine the baseline alloy microstructures and the microstructural distribution of noble metals and actinides. Corrosion tests of the metal waste form alloys indicate that they are highly resistant to corrosion.

Jan 1, 1996

By Jong-Jin Pak

The present work reports the commercialization of a recycling process of spent acid to recover molybdenum. The process consists of ammonia gas neutralization of spent acid containing molybdenum, crystallization and filtration of ammonium molybdate, roasting and hydrogen reduction of molybdic oxide to produce a commercial grade molybdenum metal powder. The mother liquor, highly nitrogeneous residual solution after the filtration of ammonium molybdate, can be utilized to produce chemical fertilizers.

Jan 1, 2006

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By Peter Kong

This paper provides a general discussion of atmospheric-pressure plasma generation, processes, and applications. There are two distinct categories of atmospheric-pressure plasmas: thermal and nonthermal. Thermal atmospheric-pressure plasmas include those produced in high intensity arcs, plasma torches, or in high intensity, high frequency discharges. Although nonthermal plasmas are at room temperatures, they are extremely effective in producing activated species, e.g., free radicals and excited state atoms. Thus, both thermal and nonthermal atmospheric-pressure plasmas are finding applications in a wide variety of industrial processes, e.g. waste destruction, material recovery, extractive metallurgy, powder synthesis, and energy conversion. A brief discussion of recent plasma technology research and development activities at the Idaho National Laboratory is included.

Jan 1, 2006

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By G. G. Barbante

Copper anode slimes are a valuable source of the precious metals, and selenium and tellurium. They are mineralogically complex and this has led to a great variety of process flowsheets for treating them. The traditional pyrometallurgical method utilises oxidation in a reverberatory furnace, but has numerous shortcomings. Recently deep-bath intensive smelting methods have been developed for use in the larger refineries. Despite these process advances, the thermodynamics of the reactions involved remains poorly understood. An initial description of the thermodynamics of slimes smelting is presented, but is severely limited by a lack of basic data. It is shown that slimes smelting is superficially similar to copper converting, but has many unique features. More basic thermodynamic data on selenium-based systems are needed before the process model presented can be further refined, and work in this direction has already commenced.

Jan 1, 1994

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992