Search Documents

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion-resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Jan 1, 1997

By James B. Lincoln

The Schaffer linear kimberlite complex and Aultman kimberlite diatremes comprise a major part of the State Line kimberlite district of Colorado and Wyoming, which encompasses approximately 200 sq mi (500 km2). The district is located along the eastern flank of the northern Front Range and is underlain prin- cipally by Precambrian granites (approx. 1.4 b.y.) which have been intruded into an older (approx. 1.75 b.y.) metamorphic complex. The kimberlite occurrences are Devonian in age and are related to older Precambrian linear structures. The Schaffer kimberlite complex is a dike or fissure system with enlargements or blows developed at the intersections of cross faults; the two Aultman occurrences are diatremes. Kimberlite within the Schaffer complex is predominately grey to green phlogopite-calcite kimberlite breccia and tuffisitic breccia. Carbonate is abundant in some phases. Inclusions of host granite are common and locally abundant. Upper mantle peridotite, pyroxenite, and eclogite and lower crustal granulite xenoliths are present at many localities. Four phases of tuffisitic kimberlite breccia occur in the Aultman diatremes. These breccias are characterized by high carbonate and serpentine contents. Xenoliths of upper crustal granite, lower crustal granulite, and upper mantle assemblages are abundant locally. Lower Paleozoic sedimentary rock xenoliths are also abundant in the Aultman diatremes but are absent in kimberlite of the Schaffer complex. From 1979 through September 1982, Cominco American, Inc., conducted geologic mapping, petrographic studies, geophysical surveys, geochemical surveys, and auger drilling in the Schaffer-Aultman project area as part of an extensive evaluation program of kimberlite occurrences. Forty bulk samples (approx. 8,000 metric tons) were excavated from the occurrences and then were processed for diamonds at Cominco American's heavy media separation and diamond recovery test plant at Fort Collins, Colorado. Indicated grades from the Schaffer and Aultman kimberlites range from approximately 0.5-1.0 carat per 100 metric tons and as such, the occurrences do not appear to approach economic viability at this time.

Jan 1, 2013

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

By Y. C. Guan

The leaching kinetics of chalcopyrite in ammonium iodide solutions with iodine has been studied using rotating disc. The variables studied J include the concentrations of lixiviants, rotation speed, pH of the solution, reaction temperature, and reaction product layer. The leaching rate was found to be independent with the disc rotating speed. The apparent activation energy was measured to be about 50 kJ/mole from 15°C to 35°C, and 30.3 kJ/mole from 35°C to 60°C. Experimental findings were described by a kinetic model, and the overall rate was found to be: (formula)

Jan 1, 1997

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By C. Ek

Tailings originating from the gravity concentration of a gold ore containing about 14 g/t Au have been treated by various beneficiation methods. These tailings have been screened on the 147 and 74 micron sieves and the two coarsest fractions have been separated on shaking tables with unsatisfactory results, but the concentrates have been examined in polished sections for mineragraphic analysis. Very simple flotation flowsheets have been applied to collect most of the gold, recovery and grade varying with the regrinding time in a ball mill. Cyanidation tests have shown that this type of treatment is also applicable to such tailings.

Jan 1, 1991

By F. Kennedy

Consolidation Coal Company (Consol) supports an active R&D effort to improve the safe, productive mining of coal and to utilize coal in an environmentally acceptable manner. Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1.0% of Consol coal sales which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with utilizing the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1989

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By Basilio Giurgola, Federico Bonaiuti, Norbert Fuegenschuh

The North East Boundary Tunnel (NEBT) project in Washington, D.C. requires design and construction of several SEM adits which have to be built between lateral shafts and the NEBT-TBM Tunnel. The paper describes ground improvements, the actual excavation, and also the final lining works. Schedule and sequencing restrictions provided some unique challenges which had to be considered when designing and constructing these mostly short, but essential portions of the project

Dec 1, 2022

By Eugene C. Spilker

Cross country belt conveyors are becoming the preferred method of bulk material handling in the industrial complex. Installed cost, maintenance, reliability, simplicity and operating expense enhance this choice, especially when faced with rising cost and questionable availability of liquid fuels. Conveyor flights are getting longer, faster, and higher in capacity, and are being installed in rugged terrain. Rights of way are often difficult to obtain. All these considerations lead up to design aspects well beyond those for in-plant conveyors. This paper points out some of the aspects that lead to the successful design of a cross country belt conveyor system.

Jan 1, 1980

By John W. Critchfield

This paper presents an overview of some of the basic issues related to tunnel construction in the presence of flammable and toxic strata gases. Gas properties and possible sources are outlined for the various gases that are commonly encountered underground. Assessment of potential gas hazards prior to construction is discussed. Measures for mitigating the problem during construction are summarized. This RETC Session on Gassy Ground has been organized by the Underground Technology Research Council (UTRC), Technical Committee on Gassy Tunnels.

Jan 1, 1985

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By David Wilson, T. V. Rao

INTRODUCTION The Alchem trona mine, owned and operated by Allied Chemical Corp., is located approximately 32 km (20 miles) west of the town of Green River, and 8 km (5 miles) north of Interstate 80 in southwest Wyoming. Trona, a naturally occuring sodium sesquicarbonate (NaCO3 • NaHCO3 • 2H2O), is used for the production of sodium carbonate (Na2CO3), commonly known as soda ash. Present annual US consumption of soda ash is approximately 9.07 Mt (10 million st), out of which approximately 7.3 Mt (8 million st) is produced from the Wyoming trona mines. About 44% of soda ash is consumed by the glass industry; 3 % by exports; and the remaining portion by paper, chemical, soap, textile, and nonferrous industries. Allied Chemical operates an underground mine at an average depth of about 488 m (1600 ft). There are three other trona mines in the area operated by FMC Corp., Stauffer Chemical Corp., and Texasgulf Inc. (see Fig. 1). Allied Chemical became interested in southwest Wyoming trona deposits in the early 1940s. Explora¬tion work was begun in 1959 with the acquisition of federal leases. Exploitation of the reserves began in 1968. Two shafts, one 6.1 m (20 ft) and another 3.7 m (12 ft), were completed prior to 1968. The 6.1-m (20-ft) diam service shaft is divided in half by a cur¬tain wall, with one half used for men and material and the other for ventilation as a return air shaft. During the period from 1968 to 1974, the 3.7-m (12-ft) shaft was used as production shaft with two 7.3-t (8-st) skips. Due to the increased demand for soda ash, plant and mine expansions were completed during 1974. Under this expansion, the material handling system capacity was increased by constructing a new 2721-t (3000-st) capacity ore bin, sinking a 6.1-m (20-ft) diam produc¬tion shaft, and installing a friction hoist with two 22.7-t (25-st) skips. The Alchem mine manpower is 484 employees and about 2.3 Mt (2.5 million st) of trona was produced during 1976. Three different mining systems are used at the Alchem mine: conventional, continuous, and longwall. Allied Chemical introduced its first longwall unit in 1973, which was also the first longwall system introduced in the Wyoming trona district. At present, four conventional, seven continuous, and two longwall units are in operation. This equipment is operated in ten production areas. GEOLOGY The bedded trona and trona-halite in the Green River basin of southwestern Wyoming is a major re¬source for the nation. There are 25 beds that exceed 0.9 m (3 ft) in thickness and underlie areas of about 2590 km2 (1000 sq miles). There are other minor beds that range in thickness from 0.3 to 1.2 m (1 to 4 ft). Allied Chemical's Alchem mine is located in bed 17. The trona bed numbering system starts at the lowest elevation and increases upwards. The trona beds are in the Wilkens Peak member of the Green River formation. The Green River formation was deposited in a lake that began in early Eocene as a large body of fresh water, shrank in size and became saline, and then became fresh water again. The sedi¬ment during the saline phase of the lake, which includes the trona beds, is called the Wilkens Peak member. The underlying freshwater lake deposit is called the Tipton member and includes a 25.9-m (85-ft) sand unit which is a high pressure, low permeability aquifer. The over¬lying sediment is called the Laney shale. The Green River formation is underlaid by the Wasatch formation and overlaid by the Bridger formation (see Fig. 2). The structure of the beds in the area of the Allied Chemical mine is mostly postdepositional asymmetrical folds of small amplitude. These folds range in size of 3 to 6.1 m (10 to 20 ft) to as much as 45.7 m (150 ft). The trend of the folds is northwesterly with the north¬east flank of the anticlines having a steep dip and the southwest having gentle dips. Trona bed 17 varies in thickness from 2.4 to 3.4 m (8 to 11 ft) over the 93.2 km2 (36 sq miles) holdings of Allied Chemical and is flat lying except for the rela¬tively minor folding and a negligible regional dip of about 0.017 rad (1°). Trona occurs naturally in several physical forms in the Green River basin, being both massive and crystal¬line. The trona ore in the Alchem mine is a fine-grained massive ore with a compressive strength of approxi-

Jan 1, 1982