Search Documents

By M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. Flotation responses of these minerals in the presence of potassium oleate and sodium silicate are presented and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium¬ bearing minerals such as fluorite from calcite (1,2,3) and scheelite from calcite(24) and apatite(2,5) almost always involve the use of sodium silicate, for example. The mechanisms by which sodium silicate functions as a depressant are still not understood; this fact is probably due to a number of reasons. That is, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species. (6) In addition, the type and concentration of these species depend on the ratio of Na20 to Si02, the concentration of sodium silicate, and the pH of the system. (6) At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant.

Jan 1, 1968

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By James M. Baylor

Ladies and geltlemen, it is indeed a privilege and a pleasure to be here in Denver with you. I want you to know too I'm not a stranger out here. Golden, Colorado is the headquarters of A. T. Massey Coal Company's Western Division, headed by Vice President, Gregory H. Hoyl. I also have a very close friend and fraternity brother who works and lives in Denver so I could talk on and on about this area and our western coal properties, but it's Massey's coal terminal business I'm to focus in on today, and that's a horse of a different color. So on to the subject of my address: MASSEY COAL TERMINAL INVOLVEMENT As I have stated on other occasions, A. T. Massey Coal Company, for better or for worse, is in the coal terminal business.

Jan 1, 1981

By J. Ludden

By Sims Some two years ago we began investigating low coke button bituminous coal for use at our Bound Brook, New Jersey plant as a replacement for anthracite. Since August, 1957 the plant has been operating continously on this coal with the exception of a new 200,000#/hr, cyclone boiler. This study was motivated not from our desire to conduct combustion research, but for the sole purpose of reducing our steam costs, The indications were that the economics were greatly in favor of the use of the bituminous coal. The attempts to reduce the costs have developed some knowledge that has enabled this program to succeed reasonably well as will be discussed later by Mr. Ludden. The production of steam size anthracite is dependent upon either the reclamation of old culm banks or the breakage in the production of the domestic sizes. The anthracite industry has not as yet been able to cut, its mining costs to the point where the production of steam sizes has become a profitable business. This has resulted in two basic problems: (1) A constantly rising price in an attempt to have those sizes carry their share of the cost and, (2) Periodic shortages of supply when the demand is good but the market price prohibits the mining of anthracite to produce those sizes only, These conditions have made the long range forecast appear as though the price would go even higher and/or the supply at times be critically short.

Jan 1, 1958

By R. B. Hawkins

The discovery of the gold deposits of the Jerritt Canyon district and the construction of the E. R. Bell Mine is one of the significant mining developments in the United States during the past ten years. This mine will exploit one of the larger deposits of disseminated gold presently known, with proven, recoverable reserves in excess of 67.6 million grams of gold. Interest generated by the success of this project has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell Mine, is a 70/30 joint venture between Freeport Gold Company and FMC Gold Incorporated, both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan, Inc. and FMC Incorporated. Under the terms of the joint venture agreement, Freeport Exploration Company, another Freeport-McMoRan affiliate, manages the exploration and pre-mine development. Drilling, design, construction and management of the Bell Mine are provided by Freeport Gold Company.

Jan 1, 1982

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986

By Robert T. Beckman

Education of inspection and operating personnel is essential to protection from radiation hazards in the mining industry. For over 10 years, MSHA has presented the only formal course on radiation measurements and control available to the mining community. Course objectives and content are described in this paper.

Jan 1, 1981

By M. S. Safarzadeh, V. Agarwal

"The solvent extraction of cerium(III) and samarium(III) from mixed solutions of all rare earth elements (REEs) except promethium using PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), an acidic extractant, was investigated. The effects of aqueous equilibrium pH, various acids (sulfuric acid (H2 SO4 ), hydrochloric acid (HCl) and nitric acid (HNO3 )), initial metal ion concentration and extractant concentration on the solvent extraction of Ce(III) and Sm(III) were systematically studied. From the experimental results, HNO3 and HCl were found to be the preferred aqueous media for the solvent extraction of both Sm(III) and Ce(III). The most promising experimental conditions of pH, PC88A concentration and metal ion concentration were identified for the extraction of Ce(III) and Sm(III). Separation results showed that H2 SO4 at pH 2 provided the best separation between Sm(III) and Ce(III). IntroductionIn recent years, demand for rare earth elements (REEs) has increased significantly because of their many commercial applications. REEs have especially important high-tech applications owing to their unique physical and chemical properties, and they are used in a wide range of areas such as catalysts, ceramics, magnets, lasers, glass, neutron absorption and alloys. As REEs have very similar physicochemical properties, their separation and purification from each other is challenging and gaining significant interest. Samarium (Sm) and cerium (Ce) are found in different REE minerals, including bastnäsite ((Ce,La,Nd(CO3)F), xenotime (YPO4) and monazite ((Ce,La,Nd,Th)PO4) at major production sites in the United States and China, as listed in Table 1 (Bleiwas and Gambogi, 2013). The most common acidic organophosphorous extractants used for REEs extraction and separation are DEHPA (di-(2-ethylhexyl)phosphoric acid), PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) and Cyanex 301 (bis(2,4,4-trimethylpentyl)dithiophosphinic acid) (Sarangi, Reddy and Das, 1999; Surampally et al., 2012; Tian, Jia and Liao, 2013). Out of these extractants, PC88A is known for providing higher separation factors (Acharya, Mishra and Misra, 2015). El-Hefny et al. (2010) investigated the kinetics of the solvent extraction of Sm from chloride media using sodium salt of Cyanex 272 and reported the extracted species to be Sm(OH)A2•2HA. Lee et al. (2005) investigated the solvent extraction of Sm(III) with PC88A and saponified PC88A from chloride solutions and found the stoichiometry of the extraction reactions to be 1.5 with PC88A and 3 with saponified PC88A."

Jan 1, 2017

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By Joseph E. Worthington

The Haile Gold Mine is one of the earliest gold discoveries in the eastern United States as well as one of the largest gold producers from that region. Gold was first discovered in the gravels of what is now known as Haile Gold Mine Branch in 1828 on lands then owned by Colonel Benjamin Hale (spelling not the same). Small placer workings were immediately started and it was not long before the surrounding residual soils and saprolites were also found to contain gold. Following the presence of gold in the residuum eventually lead to the discovery of the underlying gold-bearing lodes that actually outcropped in saprolite form where not masked by heavy vegetation or a thin veneer of Coastal Plain sand. The earliest attempts at production, immediately after discovery, utilized slave labor, washing gravel and residuum from leased tracts that were 15m (50 ft) square. Several at- tempts at small milling operations were made during the en- suing decades, but there was really no substantial or successful production until the 1880s.

Jan 1, 1990

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By T. Karlkvist, H. R. Kota, F. Andreas, B. I. Pålsson

"Separation of different calcium minerals have long been an interesting and challenging problem. In this investigation calcium mineral separation is examined by: microflotation, zeta potential measurement and adsorption, using novel collectors having two functional groups instead of one. In theory, by varying the distance between the functional groups, it could be possible to preferentially target one calcium mineral by matching the spatial distance between the sites on the mineral surface. In this investigation two new surfactants have been tested to estimate their ability to float apatite and/or calcite. Preliminary findings show that an increase in distance between the functional groups favors one mineral over the other, and this might be due to differences in the mineral surface structure. INTRODUCTION Apatite is a strategically important mineral which has both great value for industrial use as a precursor to phosphoric acid; and in the agricultural industry as an important source of phosphorous in fertilizers. This has led both the European Union and the United States to recognize it as an important resource for the future. Currently there is no lack of apatite in the world, but it is important to develop the beneficiation to ensure future supply. A common problem in apatite flotation is the selectivity towards calcite, which it is commonly associated with. Although calcite is an important industrial mineral its abundance makes it not usually worth to extract from apatite ores unless it is easy to separate1,2. Both apatite and calcite are semi soluble minerals with calcium as one of their constituents. The most common way to separate apatite and calcite is to use flotation. A process that involves making the mineral particles to extract from the system hydrophobic by adsorbing a collector on the mineral surface. One way to study collector adsorption on a mineral surface is by zeta potential measurements. The zeta potential is the charge at a slip plane a short distance from the surface. By measuring the zeta potential with and without the presence of collector it is possible to investigate if the collector is present at the surface or not, a change is indicative of collector adsorption. The zeta potential of fluorite, apatite and calcite without collector can be seen in Figure 1. The small difference in zeta potential between apatite and calcite shows the similarity in their surface properties and gives an indication of their separation difficulty. One additional problem with semi soluble minerals is their tendency to slightly dissolve in the pulp and thereby change the ionic composition of the solution. This makes separation and research problematic as the freed ions may readsorb on the mineral surface and interfere with the collector adsorption on the mineral surfaces3–5."

Jan 1, 2016

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1992

By Robert W. Buechley, Charles R. Key, Jonathan M. Samet, Marion V. Morgan, Arnolfo A. Valdivia

INTRODUCTION The Uranium Epidemiology Study at the University of New Mexico was initiated in 1977 with the objective of assessing health effects of uranium mining in the Grants, New Mexico, area. The planned approach was a cohort study of mortality that would capitalize on the availability of health records at the Grants Clinic. During the first year, emphasis was placed on determining the feasibility of the proposed study: Were adequate records available? What was the quality of available information? Could a cohort be established? The first year's work confirmed the study's feasibility (Buechley, 1979). Subsequent efforts have focused on the health and exposure data base and comprehensive follow-up. A retrospective cohort study of early miners is in progress; a prospective cohort study of miners who began working under the current Federal standard is planned. This report will summarize the current status of the Uranium Epidemiology Study. A chronology of the study's activities follows (Table 1). TABLE 1. Uranium Epidemiology Study Timetable 12/77 Official start of study. 12/77-8/78 Abstracted Grants Clinic records of 21,780 persons examined for mining companies from 7/57 through 12/76. Checked company personnel records to establish who had worked underground 1 year or more through 12/76. 7/78- Obtained physical exam and mining history information on qualified miners from Grants Clinic and companies. 9/78- Obtained working level month information from companies and other sources. 12/78- Checked qualified miners list with New Mexico death tapes and New Mexico Tumor Registry files. 9/80- Submitted qualified miners list to Social Security Administration for search of its records. 12/80- Obtained copies or abstracts of early State Health Department and Mine Inspector's reports. 3/81-4/81 Conducted Pilot Respiratory Disease Survey. 3/81- Verified underground status of qualified miners via company personnel records. 3/81- Verified smoking and mining histories of qualified miners via Grants Clinic records. 3/81- Began establishing cohort with first underground experience after 1970. 4/81- Checked qualified miners list with Post Office, Voter Registration Office, Motor Vehicle Division, telephone directories, city directories, and other sources. BACKGROUND Uranium Mining in New Mexico The Grants, New Mexico, uranium belt measures some 110 by 25 miles in Cibola, McKinley, and Sandoval counties (Kelley, 1963). The three chief mining districts are, from east to west, Laguna, Grants, and Gallup. Average annual production was about 5,500 tons, or 45% of United States uranium, from 1966 through 1978. Despite a drop in this figure in 1979, to 40%, New Mexico still leads the nation in uranium reserves and production (Hatchell, 1981). In 1918 carnotite, a yellow uranium vanadate, was identified in the Shiprock area (Chenoweth and Learned, 1980; N.M. Energy and Minerals Department, 1981). It received little attention at the time because of its apparently limited volume. In 1950 an important uranium outcropping was discovered by chance in limestone at Haystack Butte, northwest of Grants. In 1951 deposits were discovered in sandstone at Poison Canyon, north of Grants, and at Jackpile, northeast of Laguna. In 1955 finding of radioactive cuttings at an abandoned oil test site near Ambrosia Lake led to drilling and discovery of the first underground deposits (Melancon, 1963). Ore bodies were also found near Church Rock in the 1950's (Rautman, 1977). A uranium rush followed. At various times during 1952-1962, 60 mines and 5 mills were in operation (Gay, 1963). In the early 1960's the price of uranium fell, and many miners left the area. Subsequent market fluctuations have produced shutdowns and consolidations, development and expansion. Many early uranium miners came to New Mexico with

Jan 1, 1981

By M. A. Vergara, J. A. Botín

"The decline of the “super cycle” has placed an end to a decade of production-focused strategies, with operating cost growing at rates higher than production. Today, the sector is placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. However, most cost management systems in the minerals industry are not conceived as value driving tools but to meet financial accounting and reporting needs. This research draws from a the development of an innovative cost management methodology that applies Activity-Based Bottom-Up cost budgeting and continuous improvement tools to develop a value-driven cost management system for sustainable improvement of operational efficiency and cost reduction. The methodology was successfully tested in the Andina underground mine III Panel sector of Corporation del Cobre (CODELCO), in Chile. INTRODUCTION Cost management is fundamental to profitability of any industrial project. Even more essential in mining, an industry that deals with commodities, which prices are dictated by the market and are beyond the management capacity of the company. The end of the mining “super cycle” and the advent in 2008 of the Global Financial Crisis (GFC), placed an end to a decade of production focused strategies, with operating cost growing at rates higher than production. The sector was placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. Many mining companies have seen themselves into the urgent need of cost management systems capable of achieving sustainable productivity gains and consistent profitability. Cost management is composed of three main processes: estimation, budgeting and control [1]. A number of conventional techniques have been used for cost estimation and budgeting for many years. However, most cost control systems in the minerals industry cannot be referred to as “cost management” since they are conceived to fulfil accounting and reporting needs, rather than to improve operational efficiency [2]. In general, conventional cost budgeting and control systems in mining use a “top-down” methodology, which lacks of necessary details, and fail as a management tool leading to undesirable results [3]."

Jan 1, 2016

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution.