Search Documents

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

"History - How did you get into mining and involved with SME?Unlike many past presidents, I do not come from a mining lineage. I liked math in high school and believed I wanted to be an engineer. I told my math teacher that, and he laughed in my face. I believe that humiliation is what carried me through engineering school. At the time my ability to go to college relied on how inexpensive I could make it. My brother told me that there were a lot of scholarships in mining engineering, and I should apply to mining schools. As usual, he was right and I was off to the University of Idaho to study. My first summer break I got a job with Hecla at a mine in Arizona. I was a laborer on a shotcrete crew. I knew after the first summer that I loved underground mining, and I never considered changing disciplines. Looking back, I was working in miserable conditions (hot, humid), on a miserable job (shotcrete), where I got injured, and two summer student roommates died in a car accident on the commute home after work. I had every reason to hate the industry, as I had seen virtually everything bad about what we do. But I didn’t, I loved it. I said I was good at math, I never said I was smart.I joined SME in college because I was told to by the head of the mining school, Dr. Jack Hoskins. You did what Jack told you to do. I got involved because I went to an annual meeting and the papers in the underground sessions were terrible. I refer to bad papers as the “Tensile strength on cable bolts in sub-arctic regions on Tuesday” papers. Real snoring fodder. I don’t remember who I was complaining to, but they told me to quit my grumbling and fix it. So I chaired a session, and tried to get only good quality papers, something that has been my mantra for years with the Mining & Exploration Division. I also volunteered to help the local sections too. Then one day I woke up as president.What is your opinion of the health of the mining industry?The mining industry is in bad shape. Coal is under attack and will likely never recover to its former greatness. Our President has banned new coal leases, and the state of California is forcing people it does business with to divest their interests in coal companies. And that all happened in just in a few short weeks this January. Usually in America you get a trial before you are given a death sentence, but not with coal."

Jan 1, 2015

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By O. Tsuge, G. Hoffman

ITmk3®(Iron Technology Mark III) is an innovative new ironmaking technology whereby high quality iron nuggets are produced directly from iron ore fines and coal in a rotary hearthfurnace1). The reaction mechanism has been investigated in detail through fundamental laboratory research2)3), and the ITmk3 process has progressed from the laboratory to commercialization by the success of the pilot plant tests initiated at Midrex’ Technical Center and at the Kakogawa Bench Plant (KBP) located at Kobe Steel Ltd. Kakogawa Steel Works4)5). Pilot operations have demonstrated rapid production of the iron nuggets with complete metal/slag separation at a relatively low operating temperature. The Kakogawa Bench Plant (KBP) in Japan has logged 21 days continuous operation during which high quality iron nuggets were produced directly from fine ore and coal. The operation technology and the engineering data obtained from these pilot tests were instrumental for the scale-up of the ITmk3 process for the Mesabi Nugget Corp. pilot demonstration plant, which is located at Cleveland Cliffs Inc. Northshore Mining iron ore pellet plant in Silver Bay, MN. The ITmk3 process is an ideally suited technology for siting at the iron ore mine, as it allows the economical production of a value-added merchant iron product.

Jan 1, 2003

By A. H. Shapiro, W. –F. Leung

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micrometer-range particles that form pastelike, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake flow control structure that allows expressed liquid, from the cake in the dry beach region to be returned to the liquid pool while maintaining a high-solids throughput. To provide optimal performance with various operating parameters (i.e., feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids and slurry type), the cake flow control is adjustable. The second part of the beach is preferably at a zero angle. Tests showed that the new design allows increases in solids dryness and solids throughput. Key words: Dewatering, Centrifuge, Slurry, Fine particles, Beach decanter, Cake-flow control

Jan 1, 2003

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By T. J. Fenner

Surface and underground mining operations are often hindered by unknown tunnels and stopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or non-existent. The results of several Ground Penetrating Radar (GPR) studies for the detection of known mine tunnels in underground coal; salt, and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 meters.

Jan 1, 1992

By E. R. Palowitch

On February 5, 1973, Eastern Associated Coal Corp began shortwall mining in their Federal No. 1 Mine, thus marking the first attempt in the United States at modern shortwall mining, i.e., using a continuous miner to extract coal open-ended from pillars 100 to 200 feet wide, under the protection of a self¬-advancing roof support system (1)1/. Since then, four additional shortwall faces have been operated. While the number of face-years of shortwall experience in the United States is limited, this experience has been anything but uniform. Differences in operator motivation, coalbed parameters, geologic conditions, panel dimensions, and face equipment all have contributed to a wealth of knowledge which can provide guidance for the design of future shortwalls. The purpose of this paper is to review the history of shortwall mining in the United States and to assess its value to the U.S. coal industry in terms of the health and safety of the miner, the percentage of coal recovered, coal production, worker productivity, and relative cost performance.

Jan 1, 1976

By Gerry Norton

The purpose of this paper is to make the most complete assessment of coal cleaning methods, both process and equipment related to modern-day production and environmental requirements. In order to achieve this primary objective, a number of interdependent aspects of coal cleaning technology require evaluation and analysis. 1.0 CLASSIFICATION OF SEPARATION PROCESSES Processes and cleaning equipment can be categorized according to the important parameters of 1) mechanics of separation, 2) size range application, 3) range or variance in accuracy of separation related to 2) above, and 4) feed-size ratio affecting 3) above.

Jan 1, 1977

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By H. J. Brown

Pluess-Staufer (California) Inc. Lucerne Valley California operation is one of the largest producers of high brightness high purity fme grind limestone products in western North America. The San Bernardino Mountains area of southern California contains the largest high brightness, high purity limestone mining operations and undeveloped reserves in western North America (Fig. 1, Brown 1987). Combined annual production of high brightness limestone products from several operations is approximately 1.5 million tons, with an estimated gross value of $75 million dollars per year (Fig. 2). An additional 5.0 million tons of cement grade limestone is mined by several large cement producers in the nearby Mojave area (Brown, in press). The purpose of this paper is to summarize the geologic setting, genesis and mining of white, high purity crystalline limestone by Pluess-Staufer (California) Inc.

Jan 1, 1994

By R. R. Odman

The Malmberget Division of LKAB is located 70 km north of the arctic circle and has about 2000 employees. The dominating products are sinter feed concentrate and pellets. A general flow sheet for the operation is shown in Figure 1. About 20 percent of the ore body consists of hematite, which is mined separately and processed into sinter feed concentrate. That pert of the ore consisting of magnetite passes through a dry cobbing plant. The robbing process includes crushing, screening and dry magnetic separation. The entire cobbing product is used as feed for the wet concentrator. After rod mill grinding and magnetic separation the concentrated slurry is classified. The coarse fraction (+200 mesh) becomes sinter feed concentrate and the slime fraction after further ball mill grinding and magnetic separation, becomes pelletizing feed. A small quantity of the magnetite ore is processed into special iron-rich products in the the wet concentrator. Two types of pelletizing plant are used, shaft furnace and straight grate. This paper will deal only with experience gained at the straight grate plant.

Jan 1, 1979

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By R. Day

Nahcolite is a naturally occurring sodium bicarbonate mineral found principally in the Piceance Creek Basin of northwest Colorado. An 8-m thick nahcolite bed, 610 m below the surface, is the target of this first commercial nahcolite mine. A chamber and pillar mining system is developed by solution mining parallel 8-m tall by 18-m wide by 450-m cavities initiated along horizontally drilled holes. Hot water leaching, cooling crystallization and flash drying is the process. The sodium bicarbonate product is consumed by the baking, animal feed, industrial and acid rain abatement markets. A project overview, emphasizing the combination of horizontal drilling and solution mining technologies, will be presented.

Jan 1, 1994

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996