Search Documents

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By Sam M. Pickering

Most high, purity silica is produced from crystalline quartz-generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found which is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies - Illinois Minerals Co. and Tammsco, Inc. - mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, Illinois. Both companies mine from various locations within a ten mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Company mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, Arkansas.

Jan 1, 1985

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By John C. Schneider

In the mid 60's Prochem & Hydrochem Development, it's research division, developed the high efficiency Maxflo impeller. Since the Maxflo impeller had a design that had proven to be very efficient in gas-liquid-solid contacting, it was a natural extension to apply this design to flotation & the research commenced in the mid 80's. An opportunity to test the energy savings occurred at Dickenson Mines in 1987, & comparative results with existing conventional flotation cells showed a marked increase in capacity, grade & recovery with 25% less power applied. This r success was followed by the installation of the fist agitated Flotation Colunm (5ft. dia. x 25ft. tall). As a result of the Dickenson success, Hydrochem started a comprehensive 2-part research program in 1988. At Randol Gold Forum 1988 a paper by Hydrochem was pre

Jan 1, 2000

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975