Search Documents

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By W. J. Schitt

Section 15 covers a loose collection of topics that involve water in some way. The chapters in this section include Dredge and Placer Mining (Chapter 15.1), Solution Mining: Surface Techniques (Chapter 15.2), and Solution Mining: In Situ Techniques (Chapter 15.3). The dredge and placer systems involve water in several forms. The segment on hydraulicking or hydrosluicing discusses the use of monitors to direct high-pressure water jets to move material. As such, this represents an alternative to mechanical breakage, loading, and hauling. This chapter also covers placer mining (except dry placering) where the water provides the medium that promotes the separation of minerals based on their density and other settling characteristics. Thus placer mining is generally limited to concentration of gold, tin ore, diamonds, and other heavy minerals that are already liberated and are contained in a less dense matrix. The third topic, straight forward dredging, as in sand and gravel operations, involves water only in an incidental way. Here water simply covers the minerals of interest. Thus the dredging system need only lift a payload from the submerged location to the surface for further processing or handling

Jan 1, 2008

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

By George Joseph Malina

Contractor chose and Owner allowed concrete to be placed using the arch first principle while excavating the 35'-3" O.D. rock tunnel. The contract included excavating and lining 26,000 L.F. of rock tunnel to 33'-I.D. Concrete was placed at a rate of 90LF per working day using a movable bridge to allow batching, mixing and pumping of concrete adjacent to the tunnel form.

Jan 1, 1981