Search Documents

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By Donald L. Everhart

Economic geologists faced with the task of evaluating phosphate rock deposits find it necessary to deal with a unique and a lengthy list of geologic, chemical, and economic factors before they can determine whether the deposit does, or does not, constitute "ore". The underlying fact is that phosphate rock concentrate sells at a price per ton that is among the lowest for all mineral commodities. A recent going price for a standard grade (i.e. 72% BPL) phosphate rock concentrate F.O.B. Tampa is $6.00 per long ton. This compares with sand and gravel&apos;s price of about $5.00 and $8.00, respectively, per ton. In the case of many, if not the great majority of mineral deposits, the evaluating geologist needs to concern himself principally with the fundamental and classic considerations of tonnage and grade. Barring some very unusual metallurgical problem any geologist that finds say 50 million tons of 1% copper rock, or substantial tonnages of 0.7% U308 sandstone, pretty well knows he has an ore body! Certainly the evaluation of phosphate rock starts with tonnage and grade. Any rock with less than about 10% P205 in the ground is generally ruled out as ore, on the basis of grade alone. Since nearly all phosphate rock operations must be of the large-tonnage, low-unit-value type, the tonnage of new reserves, to be considered as "ore", ought to be in the 100-million + class. But having outlined&apos; a deposit of phosphate rock having acceptable

Jan 1, 1971

By R. Adsero

The volume of data produced by operating mines has increased substantially over the last 10 years. However, the volume of data and analytical capability has been negatively correlated to equipment productivity for at least the last seven years. In simple terms, as the volume of data has increased equipment performance has declined. Table (2010) tells us that ?The calamity of the information age is that the toxicity of data increases much faster than its benefits?. More data does not guarantee improving productivity; but more data is also not the cause of declining productivity. Similarly, when equipment performance does start to improve, (it must ? there really is no option if mines want to remain competitive), it will not be the data nor analytics which causes it; it will be the people using the resources at their disposal; including the data. Data and analytics can help if the toxicity of the data can be managed. The simplest form of business improvement using data is benchmarking. The objective of benchmarking is to understand and evaluate the current position of a process in relation to ?best practice? and to identify areas and means of performance improvement. The application of benchmarking involves four key steps: (1) Analyze and understand in detail existing processes; (2) Analyze and understand the processes of others; (3) Compare your own performance with that of the others analyzed; and (4) Design and implement the changes necessary to close the performance gap(s). There are however, many in the mining industries who have shunned equipment benchmarking because they believe that, ?every mine is a pilot?. In other words, the differences between mine operations make comparisons between them of little value. This paper will present a valid approach to benchmarking equipment performance and reliability, accounting for the differences and similarities between operations, producing a result which can be used to add value to mines around the world.

Feb 23, 2014

By J. H. Kelley

In this paper, we show that the methane emission and the dust generation in under-ground mining currently and in the future pose operational, health and safety conditions which adversely Impact face productivity and worker satisfaction. One solution is the use of a dual-aircourse system of ventilation. In this concept, one aircourse captures and exhausts to the surface the dust generated and the methane emitted in coal/mineral fragmentation while a second aircourse provides workers with cleaner air for breathing and comfort. Various dual-aircourse configurations adapted to the Variable Wall Miner are analyzed and compared with conventional mining in gassy seams, indicating a marked reduction in the required air quantity and the number of aircourses.

Jan 1, 1996

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By J. B. Hanlon

In order to protect coal mine owners, operators, and lending institutions from potential environmental liabilities, responsible parties must maintain a thorough understanding of the environmental disposition of the property they control, and the ramifications of impending laws and regulations. The best way to accomplish this is to periodically conduct a Phase I Environmental Audit. The systematic approach of an audit will reveal areas of DOD compliance with SMCRA and EPA regulations which the coal owner and/or operator will be able to use to correct deficiencies and prevent the occurrence of conditions which could lead to permit block, fines, and ultimately reduced productivity.

Jan 1, 1995

By John Sasadi

Several years ago I wrote a comprehensive paper &apos;entitled, "Future Trend of Bulk Carriers" dealing with the principle dimensions of vessels and how they can be predicted; then with loading and unloading of large carriers, especially considering various designs of "Self Unloaders". Since writing the paper, many large bulk carriers were basically built along the, predictions made. Maximum size today is in the 150,000 DWT class, with few exceptions, which are combination carriers (ore-oil) or OBO&apos;s (oil-bulk-ore) in the 200-250,000 DWT class in the same paper, many references were made cautioning engineers not to design ports which could be "obsolete tomorrow", however, these were not always followed. Nevertheless, during the past few years many modern ports were built signaling the beginning of a new area of "Super Ports". Super Ports can be built for various reasons, most important to provide transfer stations where bulk material is received from large carriers then transferred to smaller vessels or barges for distribution. Obviously, opposite movement of bulk commodities can justify the building of "Super Ports", however, these are not as difficult to build for many reasons. The Material Handling Industry has developed efficient means of unloading smaller vessels or barges with continuous-type unloaders and has mastered the art of storing, reclaiming, and moving large quantities of bulk material to high-capacity shiploaders. Nevertheless, the industry has failed to design and market efficient ship unloaders which in any way could match the presently attainable shiploading rates. For these reasons, it is considerably more difficult to build "Super Ports" for incoming rather than outgoing bulk materials with large bulk carriers. The purpose of this paper is to elaborate on problems affecting high-capacity, continuous ship unloaders, especially involving large bulk carriers. For better understanding, some references will be made to the smaller, continuous barge or ship unloaders, but only as the principles affect the larger units. Additional references will also be made to exploit the present "State-of-Art" of the grab

Jan 1, 1972

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO&apos;s new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit&apos;s crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By Libby R. Ricafort, Nonato S. Retardo, Jose B. Anievas

This paper shows the metallurgical test results that led to the design of the heap leach facilities of Philex Mining Corporation. The design incorporates a water management model as process solution circulation is excessive with high rainfall intensity in the area. This poses problems in the operations requiring stringent controls than would be necessary in a less severe environment. The corporate perspective embraces on environmentally-sound mineral development. A budget is always provided to environmental management making certain that no industrial development is moved forward at the expense of the environment.

Jan 1, 1996

By H. M. Brennecke

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105°C. Iron is removed from the pregnant liquor as a jarosite and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as S°, jarosite and gypsum. The process is highly versatile and can recover precious metals, molybdenum and zinc, when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1978

By John R. Marks

In April 1990, the Homestake Gold Mine embarked on a five year, $US 23 million underground drifting and drilling program to explore promising ore targets north of the current mine. This paper describes the ventilation and air-conditioning system that was installed for the 4m x 4m x 5.2 km (ultimately) drift, which is being driven at about 8m per day in 48OC (118.5 F) crystalline rock. Design parameters are described first. Differences in South African, Canadian and U.S. drift ventilation and civil tunneling techniques proved interesting. Details are then given on equipment selection, installation and performance. Costs are included. Special note is made of safety considerations for a long, dead-end drift.

Jan 1, 1991

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle&apos;s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986