Search Documents

By C. J. B. Dreyer

In terms of resources of amphibole asbestos only South Africa can be considered. There are only two asbestos producing fields, one in the Northern Cape Province producing only crocidolite and one in the Eastern Transvaal producing only amosite. The banded ironstone sequence in which amphibole asbestos occurs is discussed, and the genesis of the fibre is briefly reviewed. The properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300,000 tonnes of amosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production, which could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. Mining methods are reviewed and evaluation techniques discussed.

Jan 1, 1978

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983

By E. Krist

The newest addition to the Anamax Mining Company's Twin Buttes copper producing complex is a by-product uranium extraction plant which was placed into service in February 1980. The plant is unusual in that it is placed internal to the copper countercurrent decantation, solvent extraction, and electrowinning plant. The plant reached full production within a month and, to date, has produced continually above design rates.

Jan 1, 1981

"INTRODUCTION Twin Metals Minnesota (TMM) (operating as a joint venture between Duluth Metals and Antofagasta PLC) assumed control of the property in 2010. Amec became involved with the project in 2011 and in 2012 incorporated additional drilling in order to update historic resource estimates. The Maturi geological model and resource estimate was updated in 2014 to incorporate additional information obtained during 2013 and 2014 drill campaigns. In 2017, Amec was purchased by the Wood Group and is now known as Wood. Geology The Twin Metals Minnesota (TMM) Maturi, Maturi Southwest, Birch Lake, and Spruce Road properties are located in northeastern Minnesota (Figure 1). This talk discussed the Maturi deposit only, although all four deposits share similarities. The following geology is summarized from Peterson and Severson (2002).Maturi lies within the Superior Province of the Canadian Shield which is exposed in central and northeastern Minnesota and extends northward into Ontario. In eastern Minnesota, the Midcontinent Rift System developed during crustal scale extension in the Mesoproterozoic Era. The rift system is traceable, as exposures of mantle-derived tholeiitic to subalkaline mafic lava flows, intrusives, and rift-filling fluvial sedimentary rocks, and in the subsurface as a gravity anomaly (high), from the eastern end of Lake Superior, arcing west across the lake basin, and extending south-southwest to northeastern Kansas. Intrusion of the Duluth Complex, circa 1,108 - 1,099 Ma, was related to rifting and is co-genetic with the North Shore Volcanic Group mafic volcanic rocks that form the hanging wall of the Duluth Complex to the east. Cu-Ni-precious metals (PM) mineralization including Pt, Pd, Au and Ag within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex. The Duluth Complex is defined as a more or less continuous mass of mafic to felsic plutonic rocks that extends northeastward for more than 170 miles (275 km) in an arcuate fashion from Duluth nearly to Grand Portage in Minnesota. It is bounded by a footwall of Paleoproterozoic sedimentary rocks and Archean granite-greenstone terranes (Peterson and Severson, 2002), and a hanging wall largely of comagmatic anorthosite, rift related flood basalts, and hypabyssal intrusions of the Beaver Bay Complex. Mineralization is hosted in the basal mineralized zone (BMZ) of the South Kawishiwi Intrusion (SKI). The SKI magmas intruded sub-horizontally between hangingwall Anorthositic Series (AN) rocks and footwall granitic rocks of the Neoarchean Giants Range batholith (GRB). The Maturi local geology and the deposit footprint (shaded orange) is shown in Figure 2."

Jan 1, 2018

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By Edwin R. (Original by) Phelps

Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining; 4) Surface mining normally recovers a- much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining [ ] methods because of geologic reasons such as the nature of the roof or bottom, thickness of the seam, multiple bedding, etc.

Jan 1, 1981

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

As 1979 drew to a close, it was obvious that China would have another good year with output of most industrial products at 3-9% above levels attained in 1978. Most increases were registered on the basis of maximum utilization of existing capacities and nationalization of procedures and methods. There were also distinct improvements in the quality and variety of products. Coal output probably surpassed the 650-Mt level in 1979. Steel output was expected to reach the 35-Mt level, an increase of nearly 10% over 1978. Based on the vast amount of housing and road and project construction, cement production more than likely surpassed 70 Mt. The nonferrous base metal industries improved somewhat in 1978, but actual output levels in recent years may have been a little higher than previously estimated by the outside world. Stagnate world demand slowed growth in the "export metals" sector. Minerals like magnesite and talc were produced at tonnages much larger than previously thought, with gold also falling into this category. Sulfur and pyrite production are still short, although a big pyrite mine was being brought into production. Barite out-put was reportedly up and fluorspar output held its own. Westerners generally concede that difficulties in transportation and power supply are holding back mineral production. Throughout 1979, basic construction continued on the majority of projects started by the Chinese and those few foreign projects contracted before the adjustment of industrial priorities. Foreign Ventures Perspective The foreign connection looms large in China's plan for modernization. In effect, it is an extension of what China wants to do in terms of "walking on two legs"-that is, develop what can be done locally to the fullest extent, then rely on international technology to move into the bigger and more complicated projects. Foreign projects are designed to complement domestic projects rather than replace them. Many foreign projects were started or continued by the Chinese in 1979. Building the necessary infrastructure for the projects is usually a Chinese endeavor and requires Chinese technicians and money. In areas with a strong economic base, this activity proceeds without foreign aid. In other areas, added funds are requested. Foreign funds can come in many forms-equipment technology, low interest loans, equity capital, advance-of-funds on the basis of future delivery in kind, and joint venture money. The Chinese are exploring all these avenues, with the strategy of minimizing foreign exchange needs for individual projects. They feel very uncomfortable with high interest rates, even though interest can be treated as operating ex¬pense rather than capital expense. Then there's the question of rights. Will Chinese sovereignty be affected? Can foreigners own land, in addition

Jan 3, 1980

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By L. John Minnick

A revised and expanded edition of a previous paper** dealing with reactions of calcium and magnesium oxides and hydroxides with pulverized coal fly ash is presented. Lime-fly ash specimens were cured at constant temperature and subjected to X-ray diffractometry, differential thermal analysis, pozzolanic reactivity tests, and microscopical investigations. Bars of limefly ash were subjected to cycles of wetting and drying, and measurements of length change were recorded. A discussion of variations within and among types of lime and types of fly ash is presented. The nature of the pozzolanic reaction is reviewed, particularly as related to compounds which are used up and formed during the aging process. The relationship between the pozzolanic reaction and the resultant physical properties of the mixtures is examined.

Jan 1, 1968

The mining industry is an important economical factor in Vietnam. Mining is presently being conducted at about 60 locations and at over 1000 mines. Petroleum extraction and coal mining are the most important parts of industry though metals such as zinc, tin, chromites, iron are also extracted. Last year the sector produced 20 million tons of crude oil, 26 million tons of coal and 500,000 tons of apatite. In particular, Vietnam is one of the world?s largest producers of anthracite, and it is one of the top producers of ilmenite and zircon in the Asia-Pacific region. The government intends to increase the mining production on all levels, however, at present one can observe adverse impacts of the mining activities on the natural environment such as insufficient waste dump rehabilitation, occurrence of acid mine drainage, mining subsidence and emissions as well as lack of appropriate water treatment facilities. This paper describes the current mining situation, future perspectives, the major environmental challenges of the country and approaches to solve these problems. Particular emphasis will be given to the research project ?RAME ? Research Association on Mining and Environment in Vietnam?, a venture carried out by universities, research centres and industry. This project is worked out in collaboration with the national Vietnamese coal and industrial minerals company VINACOMIN.

Jan 1, 2006