Search Documents

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By N. T. Rempe

Proper use of natural resources is multiple use. Underground space resulting from mineral extraction offers opportunities for deep geologic waste disposal (DGWD) which can solve many environmental problems. U.S. government projects plan to use specially mined excavations to dispose of radiotoxic and mixed waste. DGWD takes careful planning, technology transfer, and true partnership between waste generators and mine/repository operators. Using the experience, accumulated by domestic projects in preparation, and by foreign repositories in operation, U.S. mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1996

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By Randall J. Essex

The Construction Institute of the American Society of Civil Engineers recently published the second edition of a 1997 publication on geotechnical baseline reports. The new publication, called Geotechnical Baseline Reports for Construction, Suggested Guidelines, represents a 2-year effort that adds three new chapters to the original publication, as well as capturing practitioner commentary through two industry workshop sessions. The paper will overview the contents of the new publication, particularly the three new chapters.

Jan 1, 2008

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By J. Bickson, C. DeGennaro, J. Homer, M. Girman

Powered haulage and haul truck-related fatal accidents are among the most frequent at surface mines. Industry organizations developed guidance on accident scenarios to address haul truck and mobile equipment collision-related accidents. However, there is a need to investigate accident data to prioritize these scenarios and identify factors relevant to developing validation methods for collision warning/avoidance technologies and determining their capabilities and limitations. Standards and effective validation methods are necessary for improving system efficacy within mining operations and promoting industry adoption. To address these needs, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated available powered-haulage and machinery-related fatal accident reports documented by the Mine Safety and Health Administration (MSHA). Their objective was to gain a perspective for informing the development of test protocols and validation methods through determining the most prevalent accident scenarios and related factors. Our findings afford insight for addressing the most prevalent haul truck scenarios and relevant factors within U.S. surface mining environments.

Mar 2, 2022

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

By S. P. Singh

Drifts are the nerve centre of underground mining. They provide essential communications between primary openings and production areas. In view of their strategic importance in the overall safety, economy and productivity of mines, an empirical approach for blast design during drifting has been proposed in this paper. The approach was developed with the objective of minimum blast damage and provides computerized blasthole patterns for drifting operations. The drift blasting practices and problems in Canadian mines have also been reviewed in this paper.

Jan 1, 1991