Search Documents

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By Y. Okahara

The chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganeus oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were difficult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexitites of the reactions, and the possible mechanisms were discussed. Then three manganiferous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides.

Jan 1, 1969

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By Eric Eisold

The Wachovia Headquarters and Arts and Cultural Campus project in Charlotte, NC includes a 1.5 million square foot, 48-story office tower, two museums, an Afro-American cultural center and a 1,200 seat theater for the performing arts. Public access to the Cultural Campus is through two pedestrian tunnels constructed under city streets connecting to parking garages. The 5.7 m wide by 4.7 m high mined tunnels were procured through a design-build contract. The tunnels were designed as initial/final shotcrete linings with a sprayed water barrier sandwiched between layers of shotcrete. In addition, the mix design was supplemented with a cementitious admixture to develop internal water resistant properties in the shotcrete.

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By John L. Kaplin

The underground construction for the Phase I Combined Sewer Overflow(CSO) Project is on an impressive scale by any measure, appearing more so in a midsize city like Providence, RI. The Narragansett Bay Commission recently completed $350 mil-lion in construction to improve the water quality in Narragansett Bay. This project included a number of serious challenges, delays, and disputes. Looking back on this complex project completed within budget, it is hard to consider the work as anything other than a success. Along the way, this outcome did not always appear certain.

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By J. A. Mielczarski

Surface properties of minerals could be modified selectively and very specifically by adsorption -desorption (dissolution) processes. This requires a monitoring and control of the outermost surface layer at a molecular and atomic level. The nature and structure of self-assembled submonolayers and monolayers at the interface of minerals were studied by infrared reflection spectroscopy. The external reflection spectra of the adsorbed monolayers on any type of minerals: transparent, opaque or non-transparent, recorded at different angles of incidence and for two polarizations are an excellent source of information about the nature and surface distribution of the adsorbed species. The developed method allows to obtain detailed information at a molecular level about the adsorbed surface species. By combination of the simulated and experimental data, the qualitative description of the adsorbed species as well as quantitative evaluation of orientation and the thickness of the adsorption layers were obtained. This fundamental knowledge allows to determine the mechanisms of surface phenomena which govern selective separations. Examples of different surfactant - mineral systems and industrial applications will be discussed.

Jan 1, 2000

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By William R. Yernberg

The “China & East Asia Mineral and Energy Re-sources Symposium — CEAR 2000” was held Jan. 23-26, 2000 in Denver, CO. Conference sponsors included Resources and Technology Symposia of Colorado and the Asian Journal of Mining. The meeting was attended by representatives from China, Japan, Mongolia, Korea, eastern Russia (Siberia) and the United States. The US attendees consisted of interested parties from mining and energy companies, financial institutions, consultants and government agencies. In his opening statements, L. Maness, Jr., president of Resources and Technology Symposia of Colorado, said that the “goal of the conference was to make jobs and friendships and to introduce people to each other.” The conference provided an opportunity for Western mining interests, including mining companies and investors, to meet with government agencies from both sides of the Pacific.

Jan 1, 2000

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By Deborah A. Peacock

"Outer space technology and exploration have reached a tipping point, so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies worldwide are on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3.The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars.How and why are the Moon and asteroids and their resources of interest to private space industry companies? Why are the Moon and asteroids viewed as a potential business venue?Geology of the Moon and asteroids — Why do we want to mine there?Space enterprises are actively working toward establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products and distribution of the products and services in space and to Earth and beyond2.Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral-rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind."

Jan 1, 2017

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.