Search Documents

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By M. Fornaro, E. Lovera, I. Sacerdote

"The analysis of the mining laws of the different European States reveals big diversities and, often, remarkable complications. This is due, firstly, to the history and culture of different States and, secondly, to the assets of natural resources. It is therefore difficult to find a common line between the text of the various mining laws, but it can be observed that nearly all the States distinguish the mining resources in two categories: the materials whose importance is considered strategic belong to the first category; in the second category the materials whose importance (above all economic) is mainly local are comprised. The paper, analysing in detail the planning procedures in some important Countries, investigates the possible perspectives of arranging some guide-lines for a correct approach to the sustainable exploitation planning/programming of mineral resources (with particular reference to "quarry" materials, such as aggregates), considering both the environment protection and the production needs."

Jan 1, 2005

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By Gökhan Çevikbilen, Ümit Karadoğan, Sevde Korkut, Berrak Teymur

This study proposes a methodology for dewatering of mine waste using a multistage process, combining geotextile tubes and anionic polyacrylamide (PAM), which accelerates the recycling process of water for aggregate mine waste facilities. For this purpose, waste from a rock quarry located in Istanbul was investigated. Flocculation tests revealed that the use of anionic PAM at an optimum dosage reduced sedimentation time and decreased turbidity. The compatibility of geotextiles and mine waste conditioned with different dosages of the effective PAM was evaluated by rapid dewatering tests, considering the water content of the filter cake, amount of infiltrated solid content, and rate of filtration. Geotextile dewatering tests were also performed on PAM-free and conditioned suspensions. The dewatering process was optimized by the use of a geotextile tube in two stages: (i) on the unconditioned suspension and (ii) on recovered PAM-conditioned leachate. Directing PAM-free non-hazardous soil-based material obtained in stage i to alternative beneficial uses is suggested, to minimize the volume of waste. Furthermore, recycling of the effluent obtained at the second stage of the proposed method will ensure more efficient water reuse

Sep 29, 2022

By Bruce D. Hansen

For many years, Newmont has focused on improving its operations. After the merger between Newmont and Santa Fe Pacific Gold, Newmont created synergies of more than $50 million a year in Nevada. This was done primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. At its mine facilities in Nevada, Newmont has used a combination of several strategies to decrease the costs of operations and to increase profitability. These include computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and several available metallurgical processing options.

Jan 1, 1999

By D. Sohn

Work accidents have an essential impact on the economy of a country and in final consequence on each company. The main purpose of industrial OHS is to maintain and promote the health of all employees. Healthy working conditions increase efficiency and motivation and safeguard the success of the business against the background of the extremely dynamic processes of change. Maintaining and promoting the health of all employees, weather in operation, administration or on the mining site, has become therefore not only an ethical requirement but also an economic must. Creating a suitable working environment for people today entails much more than just preventing accidents and work-related illnesses. It is important to be proactive in establishing an even better culture of prevention and to convince everyone, workers and managers alike, of its importance. Especially in the age of rapid changes and above all in view of global competition we are more dependent than ever on healthy, enthusiastic, competent and creative employees. OHS provides you with the necessary competitive edge.

Jan 1, 2007

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By F. M. Doyle

Ion flotation shows great promise for recovering and removing metal ions from dilute process streams, either for environmental compliance or to recover values. This technique uses an ionic collector to concentrate non-surface active colligend ions of the opposite charge from a bulk solution at the solution?vapor interface. With a sufficiently large solution?vapor interfacial area (provided, for example, by sparging gas through the solution), the colligend can be concentrated and removed along with the collector in a foam phase. A key limitation on using the technique in the minerals industry, where many process streams contain a variety of ions and have relatively high ionic strengths, is the need to control which ions are interacting with the collector. Here the effect of three different chelating agents, namely dodecyldiethylenetriamine (Ddien), ethylene diamine tetraacetic acid (EDTA) and triethylenetetraamine (Trien), on the selectivity of copper, nickel and cobalt, or copper and alkaline earth metal ions, is reported. The results are discussed in terms of their implications for adoption in the minerals industry.

Jan 1, 2009

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008