Search Documents

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By T. J. Otto, C. H. Cloete, T. Mkhatshwa, T. J. van Heerden

The value realised by an open pit mine depends on the quality and integrity of the mine planning process as well as the level of execution against these mine plans. When managing the execution against the mine plan, how well the mine plan is executed spatially, is of critical importance. The short-term mine plan is the plan that is physically executed on most open pit mines. At the same time, the spatial mine-to-plan compliance is typically reconciled against the annual business plan. Short-term mine planning, therefore, plays an important role in the effectiveness of the spatial mine-to-plan compliance reconciliation process by providing operational teams with detailed designs and schedules, while ensuring that mining execution is spatially aligned with the business plan. The Sishen open pit iron ore mine (Sishen) strives to continuously improve spatial compliance to the business plan. Sishen enhanced the role that short-term mine planning plays in enabling the forward-looking component of the spatial mine-to-plan compliance reconciliation process. The enhanced short-term mine planning process focuses on detailed tactical sequence designs per mining pushback, the health of value chain buffers, spatial plan-to-plan reconciliation, and the associated management routines. This led to improved spatial mine-to-plan compliance to the business plan from 71% to 94% over the four-year period from 2020 to 2023 inclusive. These results indicate that the application of short-term mine planning as part of an integrated spatial mine-to-plan compliance process at open pit mines can contribute positively to improving the level of spatial execution against the business plan. This paper presents the enhancements made to the short-term mine planning process, which other open pit mining operations can consider to improve spatial mine-to-plan compliance.

May 27, 2025

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest are reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By D.W. Gentry

1. Book reviews Mine investment analysis, by D.W. Gentry and T.J. O'Neil. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50.Finance for the mineral industry, by C.R. Tinsley, M.E. Emerson, and W.D. Eppler. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50. 2. Mintek reports The folowing reports are available from the Council for Mineral Technology, Private Bag X3015, Randburg, 2125 South Africa. They are free of charge to South African addressees, but there is a handling charge of US$25 per copy for reports sent to overseas destinations. Report M291D Removal of pebbles and pre-crushing of selected feed material in autogenous milling, by D.I. Hoyer. First issued Nov. 1986, reissued Apr. 1988. 16 pp Report M350 A survey of miling and mil-lining practice on South African gold mines, by M.S. Powel. Jun. 1988. 30 pp Report M356 The distribution of cobalt in mineral constituents of the Merensky Reef and UG-2 Chromitite Layer of the Bushveld Complex, by G. Smits. Jut. 1988. 13 pp Report M359 The development of a mobile laboratory for the monitoring of gold and cyanide in alkaline cyanide solutions, by R.V.D. Robert, C. Pohlandt-Watson, H.J. du Plessis, and G.D. Marshal. Aug. 1988. 17 pp. Productivity and technology The Metalurgical Society and Geselschaft Deutscher Metalhuten-und-Bergleute are sponsoring the Symposium on Productivity and Technology in the Metalurgical Industries, which is to be held in Cologne, West Germany, from 17th to 22nd September, 1989.Non-ferrous smelting Commemorating a centenary of lead smelting and refining at Port Pirie, the Conference on Non-ferous smelting wil be held at Port Pirie from 17th to 20thSeptember, 1989. International trade fairs From 20th to 26th May, 1989,4 major international trade fairs wil be held in Disseldorf, West Germany.

Jan 1, 1988

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By M. Z. Emad, A. Hassan, M. A. Raza, M. U. Khan, S. A. Saki

Digital modelling of a surface is crucial for Earth science and mining applications for many reasons. These days, high-tech digital representations are used to produce a high-fidelity topographic surface in the form of a digital terrain model (DTM). DTMs are created from 2D data-points collected by a variety of techniques such as traditional ground surveying, image processing, LiDAR, radar, and global positioning systems. At the points for which data is not available, the heights need to be interpolated or extrapolated from the points with measured elevations. There are several interpolation/extrapolation techniques available, which may be categorized based on criteria such as area size, accuracy or exactness of the surface, smoothness, continuity, and preciseness. In this paper we examine these DTM production methods and highlight their distinctive characteristics. Real data from a mine site is used, as a case study, to create DTMs using various interpolation techniques in Surfer® software. The significant variation in the resulting DTMs demonstrates that developing a DTM is not straightforward and it is important to choose the method carefully because the outcomes depend on the interpolation techniques used. In mining instances, where volume estimations are based on the produced DTM, this can have a significant impact. For our data-set, the natural neighbour interpolation method made the best predictions (R2 = 0.969, β = 0.98, P < 0.0001).

Feb 6, 2023

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005

By M. van Schoor

The bulk of the world?s platinum production originates from the Merensky and UG2 reefs within the Bushveld Complex, South Africa. Both the Merensky and UG2 reefs are disrupted by faults, dykes, potholes and iron-rich ultramafic pegmatite bodies (IRUPs)?features that impact negatively on production, planning and safety. It is therefore advantageous to know of their presence and geometry ahead of mining. To date, no geophysical technique has been successfully applied to the routine mapping of mine-scale potholes and IRUPs. These disruptive features may vary from a few metres to several tens of metres in diameter. In this paper the applicability of in-mine electrical resistance tomography (ERT) to map potholes and other disruptions to the continuity of the Merensky and UG2 reefs ahead of mining is demonstrated using two case studies.

Jan 1, 2005

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014