Search Documents

By Bert Woodhouse

The excursions - Symposium on Ancient Mining and Metallurgy in Southern Africa by BERT WOODHOUSE Excursions add much to any symposium. They enable the participants to see something of the subject matter, and provide an opportunity for informal discussion and for the creation or renewal of friendships. In this respect the Ancient Mining Symposium was well provided for. There were two excursions and both were repeated to cope with the large number of participants.

Jan 1, 1974

By A. Moerman, M. Verreault, V. Falmagne

Noranda has been involved in the development of technologies for automated mining vehicles since 1988, and has contributed in transferring the technological foundation for the suite of SIAM products now being commercialized by STAS. Some of these technologies are now mature and available for commercial implementation in operations where a strong business case can be made for the use of automation. Noranda has successfully implemented or is commissioning the Tele-remote, Auto-loading and truck Guidance technologies at two of its operations, based on operating needs and economic justifications. Operator acceptance, training and maintenance issues have been addressed in order to ensure the reliability and availability of the automation components. These represent the most significant challenges encountered and addressed during the implementation period.

Sep 1, 2001

By A. Kijko, C. W. Funk

Methods for the analysis of seismic hazards in mines are reviewed as illustrations of the techniques that are being used in some South African mines. The classical parameters that describe a hazard are the seismic activity rate, ?, the Gutenberg-Richter value, b, and, occasionally, the maximum regional magnitude, mmax The activity rate is calculated readily owing to the inherent simplicity of its definition. The evaluation method presented for the Gutenberg-Richter b value takes into account the presence of mmax Three statistical procedures are described for the assessment of mmax which the maximum observed magnitude, Xmax a crucial role. Often, the configuration of mine seismic networks is changed, or the networks are improved, which inevitably gives rise to changes in the completeness of the seismic catalogues. The routine analysis of seismic hazards must account for these time dependent changes. A method for the evaluation of hazards is reviewed that accommodates varying levels of quality in the catalogues. Finally, the concept of the volume of ground motion (VGM) is presented. This is a technique that allows for most aspects of seismic hazards in mines. The advantage of the VGM is that a hazard can be described by one physically significant value: the volume of rock (cumulated over a time period) in which the ground motion exceeds some critical particle velocity. Data from the gold mining region in South Africa known as the Far West Rand is used in a demonstration of the discussed methods of hazard analysis.

Jan 1, 1994

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By John Freer

Over 200 delegates attended the SAIMM Colloquium on Flotation, which was held at Mintek on 22nd September, 1983. In introducing the programme, the Chairman of the Technical Programme Committee, Mr Eugene Fivaz, said that an attempt had been made to strike a balance between theoretical and practical papers, which he hoped would provide something for everyone. He wished to record in advance the thanks of the Institute to S.A. Cyanamid for sponsoring the lunch, and to Bateman Equipment Limited for the cocktail party to be held at the end of the day's proceedings.

Jan 1, 1983

By A. McCracken

Probabilistic methods for assessing the reliability of engineering systems in mining are the way of the future. So agreed the delegates of a recent short course on the subject, entitled 'Reliability-based Approach in Mining engineering Design'. This was a very successful five-day technical course sponsored by The South African Institute of Mining and Metallurgy and held at Mintek from 7th to 11th March, 1988. The main lecturer for the course was Milton E. Har, Professor of Geotechnical Engineering at the School for Civil Engineering of Purdue University, Indiana, USA. Professor Har was ably assisted by Dr Dirk van Zyl, a former student. Science quiz Teams of pupils from 37 schools within a radius of 12 kilometres of the Council for Mineral Technology (Mintek) competed in a science quiz held by Mintek at its headquarters in Randburg on Tuesday, June 7th, 1988.

Jan 1, 1988

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By E. J. Magri

For life-of-mine planning, as well as for short- and medium-term planning of grades and mine layouts, it is extremely important to have a clear understanding of the patterns followed by the distribution of gold and uranium within the mining area. This study is an attempt to reconcile the geostatistical approach to the determination of ore-shoot directions, via an analysis of the spatial distribution of gold and uranium values, with the sedimentological approach, which is based on the direct measurement of geological features. For the routine geostatistical estimation of ore reserves, the Hartebeestfontein gold mine was divided into 1I sections. In each of these sections, the ore-shoot directions were calculated for gold and uranium from the anisotropies disclosed by geostatistical variogram analyses. This study presents a comparison of these results with those obtained from direct geological measurements of paleo-current directions. The results suggest that geological and geostatistical studies could be of significant mutual benefit.

Jan 1, 1978

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By Z. Zitron, G. J. de Korte, D. W. Horsfall

This paper summarizes work carried out on the treatment of fine coal, nominally classified as minus 0,5 mm (wedge-wire screen), which is removed from the raw coal prior to the treatment of the plus 0,5 mm sizes. The minus 0,5 mm coal divides, for treatment purposes, into fines, nominally between 500 and 150 !tm, and ultrafines, nominally minus 150 !tm. Studies on processes for the treatment of minus 0,5 mm coal are discussed, and the lower size limit beneficiated is indicated for each process. The installation and operational results from a pilot froth-flotation plant treating minus 150!tm coal are described.

Jan 1, 1986

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

By I. E. Teymenson, N Fedunets

Mining-metallurgical complex is the base of any economics and influences directly on practically all branches of world economics. Therefore the task of estimation and selection of investment decisions in mining industry adequate to modern market conditions and the task of decreasing multidimensional alternatives selection uncertainty are very actual. An uncertainty of investment alternatives is explained by a number of reasons, main of which are a presence of several investors types, an unstable situation on the market and an absence of evident relations between appraisal criteria used. Maximum increasing of formalization and objectivity of information technologies applied for an estimation permits to reduce the uncertainty of investment variants estimation. A number of principled innovations, allowing to solve the task of decreasing of multidimensional alternatives selection uncertainty, are introduced into the information technology of estimating and selecting investment decisions in mining-metallurgical branch, developed by us. In the article the necessity of including a cognitive model into developed selection mechanism, which allows to take into consideration inter-influences of used critera, has been grounded. Besides, the forecasting model considering interconnected time rows has been applied for increasing the world conjuncture forecast quality. Further in the article main metrics types have been characterized and application of weighted Chebyshev’s metrics as the most compromised from all studied metrics for variants selecting has been proved, and also the developed procedure of directional search of effective compromise decisions has been described. Brief characteristic of designed instrumental means of multi-criteria variants estimation and selection finalizes the article. In conclusion expedience and efficiency of using the developed information technology for reduction of multidimensional alternatives selection uncertainty have been grounded.

Jan 1, 2003

By D. H. Hillhouse, G. Lange

Design features of a deep-level shaft by D. H. HILLHOUSE. Pr. Eng.(Visitor)- and G. LANGE. Pr. Eng.(Fellow) Design and technical features of a large, deep shaft are described, and details of the sinking equipment are given. Special features in shaft steelwork, materials handling, and station layouts are described and illustrated. The details of the precast brattice wall are given, together with the reasons for the separation of all steelwork from the brattice wall. A newly developed device for the location of the shaft conveyances while loading or unloading at underground stations is briefly described and illustrated. The paper concludes with a summary showing the rates of progress and costs for the shaft-sinking operation.

By A. N. Brown

Rock breakage by drilling and blasting is fundamental to every hard-rock mining operation. The subject was an apt choice for a mining school because many technological changes have taken place since the subject was last presented some ten years ago. However, because of the development of surface mining, it was decided that two schools should be held: one for underground mining, and the other for surface mining. The School on Underground Mining was held at the University of the Witwatersrand in February 1986.Copper 87 COPPER 87 is an international conference organized by metallurgical and academic institutions of two of the largest producers of copper in the world, Chile and Canada.

Jan 1, 1986

By M. J. Nicol, G. Cromberge, C. A. Flemming

A relatively simple rate equation for the kinetics of the absorption of gold from cyanide solutions onto activated carbon was lI5ed as the basis in the development of a model for multistage carbon-in-pulp and carbon-in-Ieach absorption circuits. The model was used in the prediction of both the steady-state and the transient behaviour of the absorption process, and the results were found to be in reasonable agreement with those observed in an extended pilot-plant campaign. A number of practical implications of the model are discussed, and an assessment is made of the economic consequences of the various process options available for the design of a carbon-in-pulp plant.

Jan 1, 1983

By E. F. E. Müller

In a search for suitable reductants for the electro-metallurgical industry. the Fuel Research Institute is conducting investigations Into the charring of coals and the properties of the chars produced. This paper gives a selection of the results obtained as an illustration of the work being done. The research is proceeding.

Jan 1, 1980

By C. A. Jermy, B. J. Venter

Excessive build-up of methane and water pressures was identified as the leading cause of some Q/the roof falls in a coal mine in the eastern Transvaal. In order to characterize the migration of the methane and water into and around the mined coal seam, a laboratory investigation of the permeability of the roof strata was undertaken. The aim of the investigation was to correlate changes in the fades with changes in permeability to enable the prediction of possible zones of pressure buildup. The tests were carried out on samples from borehole core that had been obtained from the roof strata as part of the mine exploration programme. Permeability measurements were then conducted under atmospheric and triaxial-stress conditions. For the tests under atmospheric conditions, a modified Ohle cell was used and, for the tests under triaxial-stress conditions, a modified Hoek cell was used. The liquid equivalent permeability?s of the different samples were obtained by use of ASTM D4525- 85, and these were then used as a basis for comparison. Facies type, i.e. grain size, was found to have an influence on the permeability but, owing to the variable nature of the sediments, a range of permeability rather than a specific permeability value was associated with each type of Jades. The measured permeability was bound to decrease with an increase in gas pressure. The liquid equivalent permeability was bound to increase with an increase in grain size for the coarser-grained Jades, and to decrease with an increase in grain size for the finer-grained types. The application of an external stress regime to the sample was bound to reduce the permeability, but the amount of the reduction depended on the type of stress. The permeability was also found to depend on the recent stress history of the sample. The authors conclude that the methods described are useful for the correlation of facies type with permeability, but that the results are sensitive to changes in locality.

Jan 1, 1994

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By T. R. Marrero, J. W. Wilson

The transportation, by water that flows through a pipeline, of coals in the form of water-impermeable cylinders is discussed, and shown to have distinct advantages over other forms of coal transportation, including significantly reduced costs for larger throughputs. The description of the concept comprises various aspects of the system, such as methods for the manufacture of coal logs, their injection into the pipeline, the manner in which they are conveyed in the water in the pipe, and the methods used for their preparation as feed material to electric power stations at the end of the pipeline. It is pointed out that the technology involved in the transportation of coal in the form of logs via pipelines is applicable also to other minerals and commodities.

Jan 1, 1993