Search Documents

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By S. Sekhar, S. Bhargava, A. K. Godugu, J. L. Porathur

Cemented backfilling has enabled underground hard rock mines to extract orebodies more safely with improved ore recovery. It is important to estimate the minimum required strength parameters for a backfill mix by optimizing the binder percentage to enable cost-effective and safe stoping operations. We conducted three-dimensional numerical modelling to study the effect of various stoping parameters on the stability of a free-standing backfill wall. A Mohr-Coulomb material model was used for the backfill material and the rock-fill interface. A strength reduction technique, excluding friction angle, was employed to arrive at a minimum stable strength value for the backfill. For a given combination of strength values, the stability state of the backfill wall could be demarcated using a displacement and yield zone tracking method. The numerical modelling results are compared to some earlier theoretical models. From the simulations, a predictive equation is developed to predict the required strength parameters for a backfill mix to ensure a stable free-standing wall. Examples are given of the successful use of the predictive equation at some underground hard rock mine sites in India.

May 2, 2022

By A. Chagnes

This paper presents a modelling tool that can be used to predict the behaviour of solvent extraction processes. In particular, this model allows calculating metal extraction efficiency as a function of pH, solvent flowrate, stripping flowrate and aqueous feed flowrate in the mixers-settlers. This model is applied to the recovery of cobalt from acidic chloride media by using CYANEX® 272 as extractant diluted in kerosene. Keywords: Cobalt, mixer-settler, modelling, solvent extraction

Jan 1, 2020

By C. A. F. Sweet

The inter-relationship between these parties and the effect on the outcome of the project is often grossly underestimated. There are numerous success stories where the parties have worked as complementary teams aiming at the best outcome for the client company and achieving significant success. While there are a good number of occurrences where either the roles of the parties were unclear or perceived to be different from what others in the team believed or required them to be and the results were less than desired. This usually resulted in ongoing conflict, incorrect focus, working to different agendas and the result being a less than optimum result to Client Company. Mining, by its very nature of exploring where you cannot see, be it a shaft being sunk, tunnel being developed or other excavation that needs to be made, requires a very special working relationship between the parties. To understand this, and it applies equally well to mine and plant construction and other multiple function projects, one needs to start by describing the relationship of the parties. Often people believe that because they manage ongoing complex operations and large numbers of people that they can manage projects and as such the participants will ?fall into line.? At the outset it needs to be stressed that ?Project Management? is a specific type of management and needs to be understood as such. There are enough Colleges and Universities that teach project management, not only as a subject but also as a Master Degree. As you start up your project the relationship you establish between the client, project team (C.P.T) and the Engineering, Procurement, Construction and Management team (EPCM) will largely determine how successful your project will be. It is essential that from the outset a spirit of co-operation, support and respect be nurtured, and that it be actively carried through the project life cycle. There are several methods to facilitate this including team building exercises right at the start. This time and money will be well spent and recouped many times over during the project life cycle.

Jan 1, 2005

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

Visit to the Datsun Nissan Company's body pressing and assembly plant at Rosslyn, Pretoria, and the Claremont-Danville Tunnel on 27th February, 1970. The excursion arranged for the 27th February to the Datsun Nissan motor car assembly plant at Rosslyn, near Pretoria, in the morning and the Claremont-Danville tunnel in the afternoon was well supported by some 43 members. The visitors were met at the factory by Mr Rademeyer, the Industrial Relations Manager, and members of his staff and were taken to the artisan training centre for light refreshments. There is a well-equipped training section with an air-conditioned lecture hall; we were told that such training facilities were important because of the cosmopolitan nature of the artisan staff. The visitors were divided into small parties and taken to the tool die and jig-making section, which is perhaps the key department for a factory of this nature. There the many dies for the presses in the body pressing section, as well as the complicated jigs for body welding are made. The technique for making the castings for the dies is interesting. A polystyrene model of the casting is embedded in moulding sand. In a neighbouring foundry molten metal is pressed into the headers and burns away the polystyrene, which leaves no residue, and this exactly fills the space occupied by the model. This rough casting is then machined in large copying machines (costing as much as Rl80 000). An exact plastic model of the surface of the pressing required, set up in juxtaposition to this casting is traversed by a master stylus which operates the slave milling cutter, thereby machining the surface to close tolerances. The machined casting is cleaned up by hand and finally finished in large spotting machines, using a blue dye to show up high spots, to the fine degree of accuracy required. The body pressing section was next visited. There the large number of pressed parts which make up a vehicle body are pressed out of special deep drawing steel plate. Some of the largest presses were capable of applying a pressure of 1 200 tons and cost as much as Rl85 000 each. The visitors then followed through to the assembly section where jigs are used to hold together the many pressings, which are then spot welded into body frames. The frames go to an assembly line where they are finished to the stage for painting. The continuous crawl painting assembly line carries the frames through all the stages of prime coating with zinc phosphate sprayed on in a tunnel, followed by immersion of the lower parts in a priming bath, then drying and spray painting and baking in tunnels. The body frames, after painting, join another assembly line, where the doors, upholstery and many fittings are attached. After this stage the completed bodies are lowered onto and attached to the chassis units which are largely assembled from imported parts (engines, transmission units, etc.). From the end of the line the completed cars are driven off to the trial track and then pass through a tunnel with powerful water sprays to detect leaks in the body work. The proportion of locally made parts is just on 45 per cent. An interesting aspect of the assembly organization is that, of the 140 or 160 cars completed each day there may be included some of each of the Datsun model as well as some Renault and Alfa Romeo models models which are assembled by this company. The change from one model to another several times a day does not present any difficulty to the organization. Each section of the assembly plant 'buys' the units from the preceeding section and 'sells' to the succeeding section. This means that the responsibility of each section ends when the unit is sold to the next section. The cost of repairing any faults found subsequently is charged to the section where it is found, which puts a powerful emphasis on meticulous inspections between sections to safeguard their costs. After the tour the parties assembled at the lecture hall where a lavish cold buffet luncheon was provided by the company. After luncheon Mr A. R. C. Fowler, on behalf of the Institute, thanked the Managing Director, Mr W. J. Wilson and his staff for this most interesting and well organized visit. The party then left for the Claremont-Danville tunnel. The tunnel is being driven by General Mining Federale Kontrakteurs through the Daspoort Range, Pretoria, to link the suburbs of Danville, near Iscor, and Claremont, which at present can only be reached by a nine mile detour. It is estimated that some 6000 vehicles per day will use the tunnel. Before entering the tunnel a short talk was given by Mr Ross who is in charge of operations. He called on various officials and staff of the Consulting Engineering firm, Basil Read (Pty.) Ltd., to describe the tunnel and

By J. S. C. Joubert

The Koidu Kimberlite Project is situated in the Kono District of Sierra Leone, approximately 330 km east of the capital city, Freetown. The mining lease area is 4 km2 and comprises 2 kimberlite pipes, 4 dyke zones and a number of blows off the dykes. Koidu Holdings established on the property and began dewatering and the removal of silt from the existing 30 m excavation of the No.1 Pipe in 2003. While the original planning for the pipes included conventional open pit operations, mitigating factors such as the proximity of the town, the presence of houses close to the perimeter of the pipe, the size of the pipe and the planned open pit depth with relevant stripping ratios, as well as uncertainties on the grades in respect of an underground operation, lent itself to the vertical pit concept. The vertical pit was established using an A-frame headgear for the hoisting arrangement, with sidewall support comprising a combination of 20 m and 40 m long cable anchors, rock bolts, wire mesh and pneumatically applied concrete. The pit reached steady state production in January 2007 and produced some 26,000 tonnes of head feed per month until August 2007 when mining reached a depth of 74 m below the pit collar (approximately 126 m below surface). Mining was suspended following a sidewall failure that disrupted operations. Now that the grades in No.1 Pipe have been validated, focus has been switched to an underground operation taking account of both No. 1 Pipe and No. 2 Pipe. While the mining costs for the vertical pit have been higher than for a conventional open pit, the concept did circumvent the social implications, the issue of grade consistency and diamond value at depth, as well as providing the time frame to carry out a full underground mining study.

Jan 1, 2008

By B. R. Broekman, D. W. Penman

Discussion by P.J Lloydt Broekman and Penman describe (J.S. Afr. Inst. Min. Metal., vol. 91, Aug. 1991, p. 261) the addition of sodium cyanide and zinc sulphate to the flotation feed at Prieska. They note that for 'safety sake, lime was added to the rod mil to raise the pH to 9,5', and that 'personnel working in the vicinity of the rod mil were required to wear gas masks'. Author reply to P.J. Lloyd We thank Dr Lloyd for his interesting contribution. As he correctly points out, the Prieska float had run with cyanide solutions at pH values of 6,4. In fact, it ran safely for extended period with the pH slightly below 6.

Jan 1, 1991

By M. A. Mahboob, T. Celik, B. Genc

Mineral Resources estimation plays a crucial role in the profitability of the future of mining operations. The conventional geostatistical methods used for grade estimation require expertise, understanding and knowledge of the spatial statistics, resource modelling, geology, mining engineering as well as clean validated data to build accurate block models. However, the geostatistical models are sensitive to changes in data and would have to be rebuilt on newly acquired data with different characteristics, which has proved to be a time-consuming process. Machine learning methods have in recent years been proposed as an alternative to the geostatistical methods to alleviate the problems these might suffer from in Mineral Resource estimation. In this paper, a systematic literature review of machine learning methods used in Mineral Resource estimation is presented. This has been conducted on such studies published during the period 1990 to 2019. The types, performances, and capabilities, of several machine learning methods have been evaluated and compared against each other, and against the conventional geostatistical methods. The results, based on 31 research studies, show that the machine learningbased methods have outperformed the conventional grade estimation modelling methods. The review also shows there is active research on applying machine learning to grade estimation from exploration through to exploitation. Further improvements can be expected if advanced machine learning techniques are to be used.

Nov 30, 2022

By C. W. P. Finn

On 14th April, 1980, 76 delegates from industry, universities, and research laboratories gathered at the University of the Witwatersrand to attend the Pyrometallurgy Vacation School. Professor H. B. Bell, Chairman of the Department of Metallurgy at the University of Strathclyde, Scotland, was there to lead the School, along with 12 local lecturers, who had gathered at the Hotel Devonshire at 07h30 for an Authors' Breakfast. Analytical chemistry Euroanalysis IV will be held in the town of Espoo, approximately 9 km from the centre of Helsinki, from Sunday, August 23rd, to Friday, August 28th, 1981.

Jan 1, 1980

By J. A. Cruise

From 27th to 29th September, The South African Institute of Mining and Metallurgy held a Colloquium on Equipment Alternatives in Underground Mining in Johannesburg. The Colloquium, which was highly successful, was held concurrently with the 1988 Electra Mining Exhibition. Particle characterization The Fourth European Symposium on Particle Characterization is to be held in Nirnberg, West Germany, from 19th to 21st April, 1989.

Jan 1, 1988

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012