Search Documents

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By James A. Wasson

This Bureau of Mines report summarizes the application of pilot flooding in the evaluation of a potential waterflood project. Aspects of pilot flooding discussed include choice of pilot location, confined and unconfined waterfloods, operational precautions, and comparison of predicted with observed performance. Summaries of published methods of pilot flood data analysis for determination of full-scale waterflood feasibility are presented and their use illustrated for example pilot flood data.

Jan 1, 1974

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By Glenn L. Cook

Correlations between mass spectra and molecular structures of 186 organic sulfur compounds are discussed. The olefinic ions, the alkyl ions, the CnE2n+1 ions, the m/e 61 ions, and the m/e 35 ions in the spectra of thiols are related to molecular structure. In the spectra of sulfides, the olefinic ions, the m/e 61 ions, the m/e 35 ions, the CnH2n+1S+ ions, and the CnH2n+1SH+ ions are correlated with molecular structure. For disu1fides, the correlations relate HSSF+& and RSSH+ ions to molecular structure. Base peaks of alkylthiophenes are correlated to their molecular structures. Some unimolecular reactions of sulfur compounds in the mass spectrometer are considered. A cyclic intermediate is suggested for the reaction which produces m/e 47, CH3S+, and m/e 48, CH4S+, ions in the spectra of sulfides. An expanded ring is suggested as a possible intermediate in the reactions of thiophenes. Heats of formation of sulfur-containing ions and their appearance potentials are presented in tabular form. Ionization potentials for sulfur-containing radicals and molecules are also given. Discussion of the spectra, tabulated in the appendixes, provides an insight into the relationship of the molecular structure of a compound to the mass-to-charge ratios and the intensities of the ions in its mass spectrum. Correlations of the mass spectra with molecular structures are empirically developed by observing regularities in the spectra of the reference compounds. Correlations extend the usefulness of mass spectra because they can be employed to determine the molecular structure of an unknown compound.

Jan 1, 1965

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By James C. Barker

Yttrium and rare-earth element. pegmatite dikes are associated with a peralkaline granitic and nephelene syenite complex near Dora Bay on southern Prince of Wales Island. Mineralized dikes were mapped and sampled during USBM investigations in 1987 and 1988. Coarse-grained pegmatite dikes, which emanated as late-stage magmatic fluids from the intrusion, further evolved into vein-dikes and ultimately silica-rich veins. The dikes can be traced up to two miles along a north-south zone. Lithophile elements exhibit a pronounced zonation in vein-dikes and veins that are distal to the Dora Bay complex with increasing values correlating with increasing distance from the complex. The pattern of mineralization suggests very late stage magmatic fluids containing the incompatable lithophile elements were injected into a preexisting north-south fracture zone. REE mineralogy exhibit fine-grained intergrowths of principally thalenite and bastnaesite with lessor monazite and eudialyte. Euxenite contains most of the columbium values and zircon is commonly associated with the dikes. Estimates of inferred and hypothetical resource tonnage range from 1.7 X 1C6 to 8.5 X 106 st for two deposits. Contained RED (including yttrium) averages 0.5 pct and ranges up to 2.0 pct. Deposits are of polymineralic composition and about half of this resource comprises the heavy yttrium subgroup.

Jan 1, 2011

By C. E. Wicks, J. E. Tress, F. E. Block

The Bureau of Mines investigated the effects of gamma radiation on materials and chemical reactions to obtain information that could be of value in modern metallurgical practices . Various combinations of metals and their ores and compounds were irradiated in attempts to effect reactions that might be applicable in the extraction and separation of metal values from minerals and The types of reactions studied included complexing of salts , decomposition of hydrated salts , metal chlorination reactions , leaching of ores and minerals , halogen exchange , and various reducing reactions . All irradiations were performed at the Materials Testing Reactor Gamma Facility of the U.S. Atomic Energy Commission at Idaho Falls , Idaho . Spent fuel elements were utilized as the source of the gamma radiation . Some irradiation - induced changes , ranging from mere color change to participation in chemical reactions , were noted . The greatest value of these investigations , however , was the experience acquired , which should be valuable in future explorations of similar nature .

Jan 1, 1964

By Harry R. Johnson

Laboratory experiments were conducted to study the carbon deposition characteristics of a high-gravity, paraffin-base crude oil. The results of these experiments indicate that a fuel supply adequate to initiate a combustion wave can be deposited in high-gravity-oil reservoirs. These results are significant because there has been considerable doubt whether oils over 35° API gravity are able to deposit sufficient fuel. Considered in these studies were the effects of air flux, temperature, initial oil saturation, and time on carbon deposition. Conditions that maximized carbon deposition in the laboratory and an understanding of the nature of carbon formation are shown by graphical interpretation of the data. Statistical techniques were used to design and analyze the results of the retort tests. For the same amount of laboratory work, this approach yields more information about the systems that were studied than the classical method of research presently used in many laboratories. In addition, the accuracy of calculating the effect of each variable on carbon deposition is twice that of the classical approach. This paper develops the statistical approach to research without complex mathematics, thus enabling the reader to grasp the concept of how statistics can be applied to study many complicated problems.

Jan 1, 1966

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010

By E. H. Denny

The subject of haulage and heisting hazards is one that merits the attention of everyone engaged in mining. The purpose of this circular is to the importance of such hazards as are shown by Bureau of Mines accident figures, to give some examples of recent accidents and briefly analyze the immediate contributing causes, and to discuss some general means found by metal- and coal-mining companies to minimize those hazards. Haulage and hoisting accidents collectively constitute the second most common cause of accidents in and about coal mines and the third most common cause in and about metal mines. In both these types of mines falls of ground cause more accidents than haulage, and in metal mines falls of persons in raises and similar openings also exceed haulage accidents in number.

Jan 1, 1942

By G. E. Rennick

A siphon-type laboratory airlift well was designed and operated by the Bureau of Mines to study the concurrent flow of air and oil in small-diameter pipes. Glass flowstrings ranging from to 1 inch in diameter and from L4 to 64 feet in length were equipped with various-sized air-entry jets. Liquid holdup volumes were used to correlate vertical-flow data, and empirical equations for computing gas requirements were derived. The effect of flowstring length on flow efficiency, oil- and gas-production rates, and gas-oil ratios was relatively minor at all flowing pressures. Air-jet sizes and flowstring diameters, however, had a marked effect on flow efficiency and oil- and gas-production rates. The small air-jet sizes increased maximum flow efficiency and its associated flowing pressures but decreased oil- and gas-production rates. An increase in flowstring diameter increased maximum flow efficiency with its associated flowing pressure and also increased the production rates of oil and gas.

Jan 1, 1965

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By John Nagy, Austin R. Cooper, Murray Jacobson

Data obtained in the Bureau's study of dust explosions of 313 elemental metals , alloys , catalysts , and ores comprising 54 types of material are summarized . Information is given on ignition temperature , spark energy for ignition , minimum explosion concentration , explosion pressure , rate of pressure rise , and in some instances , the admixed inert dust and oxygen concentration in an atmosphere required to prevent ignition of dust dispersions . The effects of particle diameter on explosibility and pyrophoricity are also discussed .

Jan 1, 1964

By G. A. Smyres

The Bureau of Mines conducted laboratory studies to determine the feasibility of chlorine-oxygen leaching for treating low-grade zinc sul-fide flotation concentrates. Recovery of zinc sulfides by flotation from complex fine-grained sulfide ores is substantially higher in low-grade bulk sulfide concentrates than in the high-grade cleaned concen-trates required for smelter feed. However, there is no commercial process in the United States for the treatment of low-grade bulk zinc sul-fide concentrates. Leaching experiments using reactors of 500-mL and I-gal capacity were conducted on a bulk concentrate containing 19.3 pct Zn, 35.6 pct Fe, and 39.4 pct S. The effects of pressure, temperature, and percent solids on extraction were investigated. The chlorine-oxygen leaching procedure showed promise for treating the concentrates. Zinc extractions of 95 pct or more were obtained by leaching at 50 pct solids in the temperature range of 1000 to 1200 C. Zinc extractions by leaching with chlorine followed by oxygen at reactor pressures of 50 to 100 psig were independent of pressure.

Jan 1, 1985