Search Documents

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By Paul M. Tyler

Syria is a federation of States under French mandate , comprising the Republic of Syria , the Lebanese Republic or Great Lebanon ( Grand Liban ) , the State of the Alouites , and the Djebel Druse Territory . Beirut is the center of government for the whole area , about 60,000 square miles . Syria is essentially an agricultural country . There is little manufacturing ; and with the exception of the production of asphalt and salt , the mineral industries have not yet risen to commercial importance . Whether this condition is due to a dearth of workable deposits or merely to insufficient exploration is not apparent . The mineral resources , as reported by various authorities , include asbestos , asphalt rock , bitumen , chromite , coal , copper , gold , gypsum , iron , lead , magnesite , manganese , marble and other building stones , nickel , ocher , pandermite ( a hydrous borate of calcium) , petroleum , phosphate rock , pyrite , salt , silver , sulphur , tin , and titanium ( ilmenitic beach sands ) .

Mar 1, 1933

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By Robert F. Chaiken

The Bureau of Mines is using model ducts lined with coal to study the nature of coal mine fires, their rate of propagation, their influence on ventilation airflows, and their response to sealing and other fire suppression measures. For scale-modeling purposes these studies are being carried out in various size ducts; eventually they will include a full-size mine entry in the Bruceton multiple-entry Experimental Mine. To date, work has been carried out in an insulated 9.l-m-long duct with a 5-cm thickness of coal leaving a 23-by 23-cm square opening for air ventilation. Fire propagation processes in this duct were mainly transient in nature owing to the relatively small length-to-diameter ratio. This report describes the experimental equipment employed and the results obtained to date.

Jan 1, 1979

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Joan C. Biordi

A molecular beam-mass spectrometer-low pressure flat flame apparatus has been constructed for the purpose of examining the chemical microstructure of normal methane-oxygen-argon flames and those inhibited with Halon extinguishants. Details of construction and performance of this apparatus and of related flame temperature measurements are given. Particular attention is paid to the empirical characterization of the perturbation to the flame caused by the sampling probes. The composition profiles obtained for normal flames are compared to those of flames inhibited by CF3Br. In addition to the usual stable species (CH4, O2, CO, CO2, H2O, H2, and H2CO), the inhibitor, its products and intermediates associated with its reactions could be followed. In particular, hydrogen bromide, bromine atoms, hydrogen fluoride, and carbonyl fluoride were observed. The relatively rapid disappearance of inhibitor and early appearance of fluorinated reaction products suggest a short lifetime for the CF3 radical in this system. Observation of COF2 suggests that CF3Br is effective as an inhibitor, at least in part, by virtue of its interference with the oxygen containing species of the normal chain reaction. Profiles of the 17+ peak at low electron energy suggests that the hydroxyl radical may also be sampled, but the profiles obtained are not yet sufficiently accurate to determine the effect of inhibitor on this important flame radical.

Jan 1, 1973

By J. A. McAllister, H. G. Iverson, K. C. Dean

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, laboratory studies of concentration were conducted at the Salt Lake City station on a sample of ore from the Lake Valley mines of the Newalpitt Fluorspar Corp. of Deming, N. Mex. The ore was reported to be representative of the type that would be mined for mill feed. The sample tested was found to be amenable to beneficiation by ore-dressing methods for the production of products that, when sintered, assayed over 44 percent Mn.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; Al203, max., 6 percent; Zn, max., 1 percent, Al2O3,Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premiums were paid for manganese content in excess of 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 43 percent -manganese, or more than 6 percent iron, or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that, 75 percent of the product be coarser than 20-mesh. Therefore, fine material such as table and flotation concentrates had to be nodulized or sintered. In addition, oarbcnate manganese ores were not acceptable unless calcined."

Feb 1, 1948

By R. L. Brown, H. G. Berger, E. F. Pohlman

"The Bureau of Mines in cooperation with the American Gas Association investigating the relation of properties of gas oils to the gum-forming properties of carbureted water gas. The present report deals with the effects of operating practice on the composition of the light oils from carbureted water gas. A general outline of the gummy meter problem has been presented in a previous paper.*Carbureted water gas is a mixture roughly of 80 per cent water gas by volume and 20 per cent oil gas. The latter, though small in relative volume, supplies more than half of the heating value of the gas under the present-day standard. Therefore, it is logical that the oil used in the carbureting process and the operating practices involved should be subjected to scientific study. Many investigations***** bearing on the aspects considered in this paper have been carried out in the past."

Oct 1, 1923

By Danton L. Paulson

Elevated temperature electrical resistivity measurements were made by the Bureau of Mines on arc-melted, spin-cast, and hot-pressed columbium carbide¬carbon (CbC-C) and zirconium carbide-carbon (ZrC-C) materials up to 2,000° C. The CbC-C materials displayed electrical resistivity values ranging from 35.20 microhm cm at 23° C for hot-pressed material containing 12 wt pct carbon to 242.64 microhm cm at 1,622° C for arc-cast material containing 17.0 wt pct carbon. Electrical resistivity values ranged from 29 microhm cm at 20° C for arc-cast ZrC-C containing 16 wt pct carbon to 279 microhm cm at 1,951° C for hot-pressed ZrC-C containing 21 wt pct carbon. Data from a previous report were included to establish comparison between the electrical resistivities of the CbC-C, ZrC-C, and HfC-C systems.

Jan 1, 1969

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

By R. L. Hopkins, H. T. Rall, H. J. Coleman, C. J. Thompson

Two methods were tested for separating sulfur compounds in certain petroleum fractions into types . Such separation is preliminary to identifying the compounds . Each method involved extraction of sulfides from petroleum sulfur concentrates . In the first method , the sulfur concentrate was reacted with methyl - ptoluenesulfonate to form sulfonium compounds from which unreacted portions of the sample were removed by washing with solvent . The sulfides then were recovered by heating the sulfonium compounds with anhydrous triethanolamine . The second method consisted of passing anhydrous hydrogen iodide into a n-butane solution of the sample cooled in dry ice , whereupon the hydrogen iodide adducted with the sulfides to form sulfonium compounds . These adducts separated as crystalline solids or , more frequently , as glassy viscous liquids . The sulfide was regenerated by adding water to the filtered sulfonium compound and was recovered by steam distillation or by extraction with pentane . These methods have been evaluated , using individual pure sulfur compounds and blends of sulfur compounds . They also have been applied successfully to separating sulfides from sulfur concentrates derived from petroleum fractions .

Jan 1, 1964

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969