Search Documents

By James P. Ulery, Frank E. Chase

Clay veins found in coal mines have caused numerous injuries and fatalities. These structures plague all phases of mining, including entry development, pillar recovery, and panel extraction. Clay veins also increase production costs and may disrupt or halt mining. These detrimental aspects have prompted the Bureau of Mines to investigate the physical characteristics of and roof instability problems associated with clay veins. This was accomplished by observing and mapping clay veins in surface and underground mines. The occurrence and origins of clay veins were also investigated to determine predictive capabilities. The investigators found that clay veins normally occur in more stable, less rapidly subsiding coal basins. Clay veins result when tensile stresses develop fissures which are later infilled. These fissures can be propagated by compactional processes and/or tectonic stresses active during and subsequent to coalification. The Bureau also found that associated faults, fractures, and slicken-side planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance, the roof is segmented into cantilever beams, causing unstable conditions. Consequently, the strata on either side of the clay veins should be bolted and strapped together to form a beam.

Jan 1, 1987

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By S. J. Broderick

[The authors gratefully acknowledge the assistance of O. C. Ralston, chief engineer, Nonmetals Division, Bureau of Mines, Who suggested the problem and Gave valuable aid during the course of the work. Thanks axe due also to Will H. Coghill, supervising engineer of the Southern Experiment Station, Bureau of Mines. INTRODUCTION One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and. it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950

By Paul T. Allsman

The vanadiferous deposits of the Sublette Ridge and Salt River Range, 2 miles east of Raymond, Idaho, in western Lincoln County, Wyo., were examined August 24 to August 30, 1942, by an engineer of the Bureau of Mines, who was shown these properties by W. W. Rubey of the Geological Survey, Washington, D. C. The Sublette Ridge deposits are owned by the former U. S. Phosphate Co. H. F. Chaney, Portland, Oreg., is the representative for the company. The following report covers the history of the district, outlines the physical features and communications, mentions the property, and notes the ownership. The deposits and ore are described, and work performed by the Bureau of Mines is explained in detail. Ore-dressing tests and methods are explained.

Jan 1, 1949

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By Steven W. Schmauch

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 27,930 acres of the 52,000 acre East Fork High Rock Canyon Wilderness Study Area, CA-020-914/NV-020-006A, in order to evaluate the mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 45 miles east of Cedarville, CA. Bureau of Mines personnel reviewed pertinent literature and county mining records and examined prospects or mineralized areas. There are no organized mining districts and no historical or active claims in the study area; one small pit lies in the southwest corner of the study area. Based on published literature, sample results and field observations, there are no recognized mineral, geothermal, or fossil fuel resources. Epithermal mineralization indicators are not present or exposed. Sand and gravel deposits in the study area are not likely to be developed as other deposits are closer to market areas.

Jan 1, 1986

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By Charles D. Litton

This U.S. Bureau of Mines report describes the results of two large-scale tests conducted to evaluate a prototype nitric oxide (NO)-compensated carbon monoxide (CO) fire sensor, developed by Carnegie Mellon Research Institute (CMRI). In the tests, small coal fires were allowed to develop in the presence of diesel exhaust at relatively low ventilation airflows. These tests compared the response of the CMRI fire sensor with that of other fire sensors, including the Bureau's diesel-discriminating smoke detector. During the tests, CO, NO, and smoke levels were continuously monitored in order to determine the sensor alarm times and gas levels as the fire developed. The data indicated that the NO-compensated CO fire sensor was capable of suppressing the CO produced by a diesel engine and that the sensor responded reliably to the CO produced from the test fires. The tests also showed that the Bureau's diesel-discriminating smoke detector alarmed earlier than the prototype NO-compensated CO fire sensor.

Jan 1, 1993

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By G. L. Oldright, Virgil Miller

"This paper is the ninth 4 of a series on smelting in the lead blast furnace, and the fourth on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSThe authors wish to express their appreciation to Stanley A. Easton, Frank M. Smith, and A. F. Beasley, and to their staff for the whole—hearted cooperation that made it possible to obtain the data in this publication at the Bunker Hill smelter, Kellogg, Idaho.INTRODUCTIONIn tie account written of the conditions obtaining at the tuyere zone in the blast furnaces at Tooele (R. I. 2965) the authors gave references to articles covering (1) the effect of temperature on the equilibrium 2C0 - CO2 + C, (2) experimental work that has been done on learning the gases existing at various elevations in columns of burning coke, (3) extension of this work to the tuyere zone of an iron blast furnace, and (4) the paper itself gave similar analyses of the gaseous oxides of carbon at the tuyere zone of a lead blast furnace and showed the temperatures obtaining there. There were also references in the above paper to the literature on (5) how the lead compounds likely to be present might be ex¬pected to react. A careful study of the original articles selected as references will give a good background for the present work.The following very brief recapitulation may be convenient before considering the tuyere zone in the blast furnaces at Kellogg. The ""producer gas reaction"" (1) of course goes to the left at increasingly higher rates of speed with increase of temperature. When air is blown upward through a grate and a column of hot fine coke alone, oxygen as such penetrates from some 2 to 3 inches only, under the conditions obtaining as to the amount of surface exposed per unit volume of air. When air is blown at about 20 pounds pressure through the tuyeres in the side of an iron blast furnace into a column of coarse coke (plus furnace charge) it may penetrate for 30 inches before the oxygen is entirely used, burning first largely to CO2. Within wide limits, the rate of feeding air into the furnace has practically little effect on the composition of the gases obtaining in the fuel bed of fine coke, this being true particularly of the gases leaving the bed. Some 10.5 inches above the grate the gases contained 22 per cent of CO by volume, and a little further up the CO2 had practically disappeared. This gave the familiar three zones in both the iron blast furnace and the gas producer; in order of entry of the air, in the first the oxygen burned largely to CO2, in the second the CO2 was reduced to CO, and the third the CO2 was practically absent. In the furnaces at Tooele, conditions were somewhat erratic but the first two zones were present, there being, however, no zone in which CO2 and 02 were both entirely absent."

Apr 1, 1931

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements on solutions and isolated powders provide direct evidence for the involvement of Cr(V) species in the reduction of Cr(VI) by NAD(P)H. ESR analysis of an isolated Cr(V)NAD( P)H solid yields 6 11 = 1.9831 and 6.i. = 1.9772, indicating that the unpaired electron occupies the d22 orbital of the Cr(V) ion, with square-pyramidal geometry. Addition of hydrogen peroxide (H2 0 2 ) to the N AD(P)HCr( VI) reaction mixtures suppresses the Cr(V) species and generates hydroxyl (""OH) radicals. The ""OH radicals were detected via ESR spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide and a-(4-pyridyl-1- oxide)-N-tert-butylnitrone as spin traps. The dependence of Cr(V) and ""OH radical formation on the H20 2 and Cr(VI) concentrations indicates that the Cr(V) species react with H20 2 to generate the ""OH radicals. Similar results were obtained by using various diols (arabinose, cellobiose, FAD, fructose, glyceraldehyde, ribose, and tartaric acid), a-hydroxycarboxylic acids, and glutathione. Investigations with superoxide dismutase showed no significant participation of 02 in the generation of OH radicals. These results thus indicate that the Cr(V) complexes, produced in the reduction of Cr(VI) by cellular reductants, react with H20 2 to generate ""OH radicals, which might be the initiators of the primary events in the Cr(VI) cytotoxicity.In this paper we report an electron spin resonance (ESR)3 spectroscopic detection of Cr(V) species in the reduction of potassium dichromate, henceforth called Cr(VI), by NAD(P)H and other diols. Also reported here is the detection of the hydroxyl (""OH) radical in the reaction between hydrogen peroxide (H2O 2) and a variety of Cr(V) complexes. This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step m the mechanism of Cr(VI) toxicity, mutagenicity, and DNA alteration, the details are not yet clear (1-5).Earlier studies on the mechanism of Cr(VI) reduction in cellular systems include those on the reduction of chromate by microsomes (6-8), rat liver DT-diaphorase (9), and aldehyde oxidase (10). All these studies imply that Cr(VI) can be reduced to Cr(Ill) by cellular constituents. Regarding the mechanism of Cr(Vl) carcinogenicity, Jennette postulated that Cr(V) is the ultimate carcinogenic form of chromium compounds (8). This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions (11-33). More recently, however, Kawanishi and co-workers (34) have investigated the mechanism of DNA cleavage induced by Cr(VI) in the presence of H20 2 and have argued that it is not Cr(V) itself that is carcinogenic, but it is the reactive oxygenated species (02, 10 2 , ""OH) (produced by the decomposition of the Crv(02) ¾ - ion) that cause the DNA alteration."

Jan 1, 1990