Search Documents

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By Martin Hertzberg

This Bureau of Mines report analyzes diverse observations of the rates and mechanisms for the pyrolysis and devolatilization of coal and polymethylmethacrylate (PMMA). New data are presented for PMMA, together with new morphological evidence for the microscopic structure of the pyrolysis and devolatilization wave front in coals. It is concluded that there is no substantive evidence to support the traditional viewpoint that the pyrolysis and devolatilization rate process occurs isothermally, under chemical rate control; or is described realistically by a classical, unimolecular Arrhenius function of temperature. Instead, the reaction process occurs as a highly nonisothermal, heat-flux-driven, pyrolysis and devolatilization wave front, whose speed of propagation is predictable by internal heat transport constraints. Except for the complication of its charlayer residue, whose increasing thickness insulates the pyrolysis wave front from the heat source flux that drives it, both coal and PMMA behave similarly during pyrolysis and devolatilization. For PMMA, decomposition occurs at a temperature of 3500 to 5500 C; for coal it occurs at 4500 to 6000 C. There is no evidence that the reactant temperature ever exceeds those values regardless of the source temperature to which the samples are exposed.

Jan 1, 1988

By L. K. Weaver

The objective of this Bureau of Mines publication Is to present a nomograph that provides a fast, convenient method for estimating hydrocarbon lease bonus bids for offshore acreage in the Gulf of Mexico. Discounted cash flow analyses were computed from a model derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block of offshore acreage, and the estimated income from the sale of the hydrocarbons produced from the block. The range of the variables in the financial analyses used to construct the nomograph are prices of oil, $2.50 to $5.00; recoverable hydrocarbon reserves, 44,651,476 to 127,575,645 barrels; and discounted cash flow (DCF) rates of return, 5.0 to 57.2 percent. A total of 1,234 sets of DCF data were used to construct the nomograph. The range of bonus bids shown on the nomograph is from 2 to 90 million dollars ($400 to $18,000 per acre).

Jan 1, 1973

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Aug 1, 2009

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By Kenneth L. Cashdollar

This report describes three types of optical dust probes that have been designed, built, and tested by the Bureau of Mines. Each of the probes measures dust cloud concentrations by the attentuation of light. The first is a single-path-length probe, the second is a double-path-length probe, and the third is a single-path-length probe that employs jets of air to keep the windows of the light source and detector free from dust coating. The theory of operation and the calibration procedures for each of the probes are described. The results of the Bureaus laboratory, mine, and field tests of the probes are also reported.

Jan 1, 1981

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

By Stephan Stecura

One of the principal objectives of the Bureau of Mines program for development of superrefractory ceramic materials is to obtain fundamental data on the physical properties of refractory oxides. Elements of particular interest to research workers in the Bureau include groups III and IV of the Periodic Table and the rare-earth group. This report contains thermal expansion and phase inversion measurements on oxides of scandium, yttrium, lanthanum and 12 lanthanide series elements (promethium and terbium omitted) up to 1,350°C, made by high-temperature X-ray diffractometer techniques. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures; with anisotropic oxides expansion was determined parallel to each major crystallographic axis. The combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C, and approximately 2 percent at 1,000° C, No difference in expansion coefficients was observed between heating and cooling cycles for oxides that did not undergo phase inversion. Tabular data of linear expansion, in percent, linear expansion coefficients, and graphical presentation of linear expansion as a function of temperature are presented.

Jan 1, 1961

By Robert M. Busche

[Recent developments in the gasification of coal, both by the Bureau of Mines and American industry, have intensified interest in the thermodynamic and kinetic principles necessary for understanding the reaction mechanism and rates and the physical changes that take place. In the course of a Bureau of Mines study of the kinetics of coal gasification at the Synthetic Liquid Fuels Demonstration Plant, Louisiana, Mo., a bibliography of approximately two references was compiled. They are listed n this publication and refer both to American and foreign sources.]

Jan 1, 1952

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By Richard L. Rains

During this study in 1983, the U.S. Bureau of Mines examined one mine and five prospects in the Greenwater Valley Wilderness Study Area (WSA). No mineral resources were identified within the WSA. Principal mineral commodities in the WSA are gold and silver with minor lead, and zinc. Two properties have significance; sample analyses indicate the Salsberry Prospect may have gold-silver-lead-zinc resources, and the Graham Jem Mine may have gold resources. The likelihood for development is greatest at the Salsberry Prospect, although the only recorded production from the study area was from the Graham Jem Mine; in 1908 less than 1 ton of gold-bearing ore valued at $25,000 per ton was produced. Gold, silver, lead, zinc, and copper minerals in the WSA are associated with rhyolite dikes and quartz veins in Precambrian gneissic rocks, commonly concentrated in sheared zones along the dikes and veins. Although known to contain silver-lead deposits elsewhere, Precambrian Noonday Dolomite sampled inside the WSA contained no significant mineral values. Much of the WSA is covered by relatively unmineralized Tertiary and Quaternary volcanic rocks. The Bureau collected 140 rock samples at four adits, nine shafts, four trenches, and 33 prospect pits in the WSA. In 1983, 14 lone claims and one millsite within the study area were current. No patented claims, placer claims, or coal, mineral, oil and gas, or geothermal leases were in the WSA.

Jan 1, 1985

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010