Search Documents

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Board for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy atmospheres which through neglect or accident might surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The third of these surveys covers conditions in Germany.

Jan 1, 1929

By Charles L. Kimbell

On the basis of world production data alone, 1985 appears to have been a year in which the world's mineral industry took another step upward in its recovery from the very poor years of 1981, 1982, and early 1983. Despite a drop in the output of crude oil, which was the single most significant crude mineral product from the viewpoint of value, the estimated value of world crude mineral production advanced by 3.4% to about $1,054 billion constant 1983 dollars, with output increases logged for nearly two-thirds of the commodities and forms of commodities for which the U.S. Bureau of Mines calculates a total world output. However, the economic well-being of any industry or group of industries cannot be measured solely in terms of the volume and/or value of its production, and examination of statistics reflecting other aspects of mineral industry performance shows that 1985 was a less than ideal year in many respects. In the case of consumption of mineral commodities, although there were gains registered in diverse sectors such as iron and steel, aluminum, fertilizer materials, solid fuels, and gaseous fuels, there were also proportionally small but notable declines in use among the older major nonferrous metals (copper, lead, tin, and zinc) and in the all-important liquid fuels. In the case of international trade in mineral commodities, although comprehensive data for 1985 were not yet available, there were indications that the value may well have fallen below the estimated 1984 level of $632 billion, although the volume may have increased slightly. This, if true, would be chiefly the result of declining prices of mineral commodities, and indeed, price declines were noted for a number of significant materials in terms of current dollars, and even more would register declines if calculated on the basis of constant dollars, adjusting for inflation.

Jan 1, 1987

By Doss H. White

In 1989, Alabama's nonfuel mineral industry produced a State record of $463 million of nonfuel mineral commodities, an increase of $4 million over that reported by the State's mineral producers in 1988. The new record marked the fourth consecutive year in which mineral production increased over that of the previous year. Alabama ranked 22d among the States in total mineral value. Cement, stone, and sand and gravel were the three leading mineral commodities produced, accounting for 77% of Alabama's total mineral value. During the year, there were several acquisitions by Alabama cement and stone companies, and the only tantalum mine in the United States completed its first full year of operation.

Jan 1, 1991

By J. E. Chilton

The Bureau of Mines has developed a portable flammable gas detecting system for estimating the flammable gas concentrations in a mine containing one or more combustible gases at concentrations up to 100 vol pct. With this portable detecting system, mine rescue or recovery personnel can quickly determine if they are working in a potentially explosive gas atmosphere and either leave the area or make appropriate changes in the fresh air ventilation of the mine to render the area safe. The detecting system uses a commercial, intrinsically safe, flammable gas detector with a range from 0 to 5 vol pct methane (CH4). The flammable gas detector has a catalytic heat-of-combustion sensor that can detect all flammable gases that would be encountered in a mine including methane (CH4), ethane (C2H6), carbon monoxide (CO), and hydrogen (H2). To determine the mine gas concentration, the rescue worker dilutes a sample with fresh air carried within the detecting system. The concentration of the diluted sample is then measured with the permissable flammable gas detector. The actual mine gas concentration is calculated from the product of the indicated diluted gas concentration and the system dilution ratio using a pocket calculator or the nomograph on the side of the unit.

Jan 1, 1987

By Albert H. Clough

The West Lynn Canal subarea of the Juneau Mining District (JMD) is defined by Lynn Canal on the east, Davidson Glacier to the north, Icy Strait to the south and the Glacier Bay National Park Boundary to the west (figs. C-l and C-2). This area extends along the main-land west of Juneau (across Lynn Canal) northerly, to approximately 20 miles south of the city of Haines. The only roads in the area are relatively new logging roads at the southern end constructed to support a U.S. Forest Service timber sale. There is also local road access near the community of Excursion Inlet. Access to the remainder of the region is either by boat, aircraft, or 'foot. Helicopters provide the only time effective access to all but the coastal parts of the West Lynn Canal subarea. Coastal areas may be reached by small boat or float aircraft. There is an unimproved dirt airstrip just north of the mouth of the Endicott River. This airstrip is suitable for use by light aircraft. The subarea lies within the Tongass National Forest and is managed by the Department of Agriculture, U.S. Forest Service. Approximately two-thirds of the forest lands are open to mineral entry under the current Tongass Land Management plan. The remaining forest lands comprise the Endicott River Wilderness area, which is closed to mineral entry. Private lands within the study area are sparse, with scattered homestead tracts along the coastal regions and in the Excursion Inlet area. Sealaska (Southeast Alaska Regional Native Corporation) also has land selections in the southern Chilkat Range. Tidal and submerged lands are owned by the State of Alaska.

Jan 1, 2012

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By J. A. Woolf, E. S. Leaver, A. P. Towne

"INTRODUCTION A report giving experiments dealing with factors affecting the floatation of the most commonly occurring silver minerals was published years ago. At that time we could not obtain suitable samples of many of the so-called sulfo-salts of the base metals, which are generally silver--bearing and which comprise an appreciable percentage of the natural silver ores. Since Leaver and Woolf's work was published, samples of impure tennantite and enargite have been obtained, and considerable experimental flotation work has been done with synthetic mixtures prepared from these samples. During the present national emergency, research dealing solely with the recovery of gold and silver must necessarily be curtailed. However, many deposits of strategic minerals and critical base metals contain an appreciable amount of gold and silver, the recovery of which would aid greatly in recovering the strategies by taking care of a considerable part of the cost of treatment. Because of this, the recovery of precious metals should not be overlooked entirely. As the Bureau of Mines is now utilizing all of its facilities for the development of increased domestic productions of strategic and critical minerals, this is the last report not concerned primarily with such minerals that will be published until the war ends."

Sep 1, 1942

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

By Joseph J. Wallace

1. The Investigation shows that there are six coal beds of major importance in McDowell County from the standpoint of present production - Pocahontas No. 3, Pocahontas No. 4, Pocahontas No. 5, Sewall, Beckley, and Pochontas No. 6 - and five beds of minor importance - Iaeger, Douglas, Welch, Pocahontas, No. 9, and Eagle. The Pocahontas No. 3 bed contains the largest remaining, known reserves. 2. Known measured, and indicated reserves in all beds, based on a minimum thickness of 174 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,217 Trillion short tons as of January 1, 1951. Of this total, 1,731 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these area, such reserves should be added to he total estimated reserves.

Jan 1, 1952

In 2004, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 891 underground (6.2%) and 13,587 surface (93.8%) mining operations.

Sep 1, 2007

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high-and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines.

Jan 1, 1966

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010