Search Documents

By R. H. Storch, D. C. Holt

During reconnaissance investigations of more than 300 stream areas in Idaho to determine the potential value of ilmenite in black - sand placer deposits 46 deposits were explored by churn drilling , trenching , test pitting , or shafting . The component mineral content and total black - sand content were determined for more than 8,690 reconnaissance and exploration samples . Data compiled during the investigation indicate a good potential for large , low- grade deposits containing ilmenite , monazite , columbite , euxenite , uranothorite , and other radioactive black minerals and accessory black - sand minerals . The data also indicate most deposits will be economic only if several component minerals can be recovered as coproducts .

Jan 1, 1963

By R. Havens

During the course of the investigation of possible domestic sources of manganese, engineers of the Bureau of Mines examined and sampled two manganese mineral deposits in northeastern Utah. The Daggett Chief claims are situated in the northern part of Daggett County,5 miles southwest of Manila, Utah, and approximately 57 miles from Green-River, Wyo. Owners of the property are J.E. Harris Of Salt Lake City, Utah, Nels Palleson of Manila, Utah, and J. P. Larson. The manganese occurs in a vein 6 to 8 feet wide in a shale and sandstone formation. Two distinct occurrences Of manganese are present Within the vein, and samples of each were subjected to testing. Lot A, representing .probably the major portion of the Manganese; was composed of nodules and veinlets of manganese oxides in a semicompact; gray, shaly formation. Lot B represented a 15-inch vein of dense iron-manganese ore. .Most of the laboratory work at Salt Lake City, Utah, was done on these two samples; but preliminary testing also was carried out on a small sample, physically similar to lot A, submitted by the owners.

Jan 1, 1949

Ohio has an estimated 46 billion tons of coal beneath 12,000 square miles of the eastern third of the state. Recoverable coal reserves within this vast area are estimated at 21 billion tons, 3.2 billion tons of which have been mined since 1800. Ohio is the eleventh-largest coal- producing state in the nation and ranks third nationally in coal consumption. Coal resources in Ohio lie in as many as 60 identifiable coal seams along the northwestern flank of the Appalachian coal basin. Except where interrupted by minor faults and erosional discontinuities, these rocks dip gently and uniformly to the east, simplifying the mining methods needed to extract the coal. Fourteen of Ohio's 60 coal seams are considered to be important, although only a small number of seams are currently being mined. Ohio first enacted a surface coal mining law in 1948, requiring in part a $100 per acre reclamation bond. Ohio progressively strengthened its surface mining law in 1949, 1955, 1959, 1961, 1965,1972,1975,1978, and 1981. At the time of its enactment, Ohio's 1972 mining law was one of the most stringent in the country. This law also created a state coal severance tax of four cents per ton to be used for abandoned mine land reclamation. Ohio received primacy to regulate the surface coal mining operations within the state August 16,1982. Its Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By Paul M. Tyler, Amy B. CLINTON

The four elements fluorine (F), chlorine (C1), bromine (Br), and iodine (I) form the most intimate family in the entire system of elements and are grouped under the name "halogens" or salt formers (by derivation from the Greek). The first member of this family, fluorine, is the most chemically active element known; and fluorspar, and to a less extent cryolite, the chief sources of fluorine, are important commercial minerals. Fluorine occurs in nature chiefly in combination with sodium as common salt, but it also appears in other natural compounds in sea water, salt-well brines, and bedded deposits. In addition to common salt, various compounds containing chlorine (chlorides) have long been consumed by industry on a large scale, and within the last two decades that element itself has come rapidly into prominence as one of the leading industrial chemicals. Bromine and iodine, the two retaining members of the family, are less abundant in nature and less readily isolated and in consequence of their relatively high price have found few industrial uses, being consumed chiefly in medicine and in photography. Bromine, however, is now entering the industrial field to a considerable extent, due to the rapidly growing use of ethylene dibromide in anti-knock compounds for gasoline. The present paper is devoted to bromine and iodine, but in order to compre- hend the physical and chemical characteristics of these two elements (and hence their potential economic significance) it is convenient to consider them as members of the family series to which they belong. The family relationship of the halogens is illustrated by the following:4 (1) The similarity in the chemical and physical properties of the elements and their corresponding compounds is such that the prop- erties of any one member of the family can be said to summarize or rather to typify the properties of all the other members, although fluorine diverges a little in some of its properties. (2) The gradual transition of chemical and physical properties is such that if the elementa are arranged in order F, Cl, Br, I the variation in any particular property in passing from fluorine to iodine nearly always proceeds in the same order, and that is the order of their atomic weight. Taxing almost any property and comparing its magnitude in passing from the element fluorine to iodine, or from the fluorides to the iodides, a similar graiation will be observed. Thus, take the melting point of the cadmium, calcium, barium, sodium, or potassium salts, in degrees.

Nov 1, 1930

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By L. Garner McDonald

The U.S. Bureau of Mines, under contract to the U.S. Department of Energy, investigated the erosive-wear properties of seven commercial alloys with potential applications as valves for coal-conversion plants. A dry particle, jet-erosion apparatus was used to determine the wear of seven materials: 316 and 440-C stainless steels, K-68, K-701, and K-801 cemented tungsten carbides, HC-250 white cast iron, and Haynes 6B. The alumina abrasive entrained in the nitrogen gas jet had particle sizes of 27 or 50 µm, the abrasive velocities were 55 to 170 m/s, and the particle impingement angles were 15° to 90°. The maximum specific wear for ductile materials was found to occur at impingement angles of 15° to 30°, and the minimum specific wear occurred at 60° to 90°. For the brittle materials, maximum specific wear occurred at impingement angles of 50° to 85° and minimum specific wear was at the lowest angles. As the velocity and erosive particle size increased, the specific wear increased. The specific wear was related to the velocity by the power function WocAVn, where n was 1.8 to 3.9 for ductile materials and 1.8 to 3.6 for brittle materials.

Jan 1, 2010

By R. R. Sayers

Under compuision of the present urgency to implement the President's promise to make the United States the arsenal for the democracies there is a tendency to demand a relaxation of restrictions on hours of labor and to speed up all industrial processes. The pressure is the more insistent with growing realization of the importance of the time factor in the success- ful prosecution of the war effort and the lack of skilled workers due to (2) operation of the draft, lack of an apprentice system in industry, and loss of skill by workers unemployed for long periods during the depression. With "total" war such as it is today the probabilities are that everyone will be required to exert greater effort (in many instances in activities to which they are unaccustomed) for longer periods than ever before has been necessary. The question arises, "What will be the aftereffects as well as the immediate effects on health, safety, and efficiency?" A review of the literature leaves the impression that this question has not been an- swered completely, especially as regards the ultimate effects. Mechanization, speeding up of industrial processes, mass produc- tion, and the small industrial concerns present many problems to indus- trial medicine. Does the tendency to expect the worker to produce at full speed all the time he is on the job decrease the effectiveness of the shorter working hours and cause undue fatigue, loss of efficiency, and increased accident proneness? The answer is important as this condition is likely to be intensified by the exigencies of the present emergency. According to Viteles (1)3, The increased tension under such conditions of work appears to offset the savings in muscular force made pos- sible by the machine. The tension, the speed, the subject- tion to specialization of work and a rhythm uncontrolled by the individual promote fatigue, characterized by a "decrease in the power to work, a decrease in pleasure taken in work, and a decrease in the enjoyment of the hours spent away from work."' The crowding of workers in temporary structures without proper provision for comfort and health may add greatly to the general fatigue factors already present in many industrial establishments. In 1932 Lockhart (2) stated that the production and maintenance of a healthy, satisfied industrial population is the most urgent necessity, involving problems so serious as to constitute a national task too great economically to be relegated to industrial concerns. If this was true in 1932, it must be doubly so today.

Jun 1, 1942

To design an apparatus that advances the state of the art in gas content testing equipment. The goal of the design is to incorporate improvements in testing sensitivity/accuracy, durability, and ease of operation over existing equipment. It is also desirable for the new design to successfully perform gas content determinations of multiple chemical species from a rock sample.

Jan 1, 1999

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By Edward L. McHugh

The study area, which comprises 11,500 acres, includes the 9,610-acre Whitewater Wilderness Study Area, in the California Desert Conservation Area, 15 miles northwest of Palm Springs, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of prospects and mineralized areas during the spring of 1981. The Whitewater study area is mainly underlain by granodiorite to quartz diorite and their gneissic equivalents in an igneous-metamorphic complex. Late Tertiary sedimentary and volcanic rocks locally overlie the crystalline complex in the eastern part of the study area. The study area lies between branches of the San Andreas fault system.

Jan 1, 1986

By Roy S. Nutter

An expert system advisor consultant to assist a coal mine section foreman is described in this report. The system is designed for an underground continuous miner section that is being specifically used for longwall development. The system provides three methods of operation that include normal operational mode for use underground, a training mode for use in training section foremen under controlled classroom conditions, and a demonstration mode that is free running. The Face Decision Support System or FDSS, is designed to interface with section environmental monitoring equipment and section production monitoring equipment that may appear in the future. This provides automated reprioritzation of the section foreman's job list from the system. The system 1S written in LASER which is written in C and is operated under the UNIX operating system. The objective of the entire FOSS system is to ensure that no job or piece of information important to safety or to production is forgotten because of the immediate problems confronting the section foreman.

Jan 1, 1988

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By Robert W. Geehan

A preliminary examination of the Dayton iron deposit was made in 1941 and 1942 by Paul E. Pesonen and O. H. Metzger, engineers of the Bureau of Nines. Trenching and sampling were recommended, to be followed by core drilling if favorable results were obtained. The Bureau of Mines conducted a project at the property from June to December 1942. The deposit is in sec. 6, T. 17 N., R. 23 E.; sec. 31, T. 18 N., R. 23 E.; sec. 36, T. 18 N., R. 22 E.; and sec. 1, T. 17 N., R. 22 E., M. D. B. & M., about 15 miles west of Lahontan Reservoir in Lyon and Storey Counties, Nev. It lies at an altitude of about 4,500 feet north of the Carson Plains, in the foothill section of mountains that rise to about 7,000 feet to the north of the property. The deposit may be reached by driving 12.5 miles northeast of Dayton over U. S. Highway 50, thence northerly 2.7 miles over a dirt road to the property. The climate is hot and dry in summer, with occasional thunderstorms some of cloudburst variety, and frequent high winds. Winters are usually moderate, with light snowfall and some subfreezing temperature.

Jan 1, 1949

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983