Search Documents

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Håkan Schunnesson, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD)data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al.(2018) and Navarro et al.(2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave-in rock and cavity. From it, an application for the geotechnical rock condition of ore bodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting. The procedure has been applied in the geotechnical block model results obtained from Navarro et al.(2019)’s work in the Luossavaara-Kiirunavaara AB’s (LKAB) Malmberget underground iron ore mine, Sweden. Navarro et al.(2019)’s model was developed based on102 fan-holes from five ore bodies and extrapolated to the full-scale in20 drifts with 5600 fan-holes from two orebodies. A multi-step transformation of the MWD parameters was carried out in order to minimize external influences other than the rock mass. The study shows the calculations of the variogram and kriging estimation in the 3D domain for six ring-blasts, from one of the ore bodies studied in Navarro et al. (2019)’s work to assess the continuity of the rock classes along the six ring-blasts in a 3D mapping model. For that, intermediate rings between the measured ones from the MWD have been estimated. The probability distribution of values in the entire domain of rings with measured samples has been plotted together with the rock classes identified by the blasthole paths. The results show high accuracy in the matching between the kriging and the values given by the MWD data, allowing to visualize smooth trends of different rock classes along the ring. The representation of the 3D mapping model for the six ring-blast shows clear fractured and cave-in zones developed along the drift that correspond to zones with geotechnical problems found, as from internal reports.

By Thierry Bernhard, Johan Finsteen, Charles Dowding, Mathias Jern

To bring some clarity to how different standards relate to each other a project was initiated within the European Federation of Explosives Engineers (EFEE). The first part of the project was a literature study and a survey including an evaluation of the answers provided by members of EFEE. The results were presented at the International Society of Explosives Engineers (ISEE) conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019.

Feb 1, 2020

By Amund Bruland, Vegard Olsen

This paper presents analytical assessments around unintended misfire detonation, within rock debris drilling and bench top cleaning, primarily in the quarrying and mining industry. The main purpose of the work has been to see which operation has the lowest fatal accident probability. To be able to do this a risk analysis model is developed and the basics of the model are described first in the paper. Further a practical approach of the model use is presented. This includes a summary of general fatal injury statistical data, which is used to establish input parameters in the model. The result of the work shows that the rock debris drilling operation has at least half the probability of fatal injury compared to bench top cleaning. The result of the work should bring along rewriting of the Norwegian explosives regulation. The statistical data also shows that the blasting industry generally has a high fatal injury rate compared to other industries and basic risk reference levels. Risk reduction efforts concerning the examined operations are described.

Jan 1, 2008

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Bruce R. Leland, Steven H. Smith, John D. Paulson

The USDA - Wildlife Services has been removing beaver dams with explosives for over 30 years. This paper will discuss the history of the explosives program, summarize how we've evolved, and highlight our work removing beaver dams in unique locations.

Feb 1, 2020

By Francisco Sena Leite, Vincius Miranda, PhD Machado Leite, PhD Pinto, Raquel Carvalhinha, Alexandre Julio, Dorival de Carvalho

Rock blasting, in particularly the drilling process, is one of the first processes in the stage of rock fragmentation and plays a fundamental role by influencing all the following stages. Given its importance, some proposals to optimize this process have been presented over the last few years. These proposals, while having different approaches, aim (in a large part) to minimize the costs of drilling and blasting respecting the limits of fragmentation required by primary crushing. Reviewing some recent articles leads us to an enriching experience, since the authors of these articles clearly model the problem, but do not address the mathematical solution of these models, which in turn, given their non-linear nature, have no directly and easy solution. Simple and even robust optimizers present in the market show different results and often do not converge to a single solution. To address this problem, an adapted gradient heuristicbased model was developed to try to find optimum values. Heuristics search for values of stemming, subdrilling, burden and spacing that minimize the costs of blasting and drilling. This search, which by the nature of the heuristic moves the solution in the direction of the gradient with maximum decrease to find optimal solution, found values that in turn, when compared with values presented by market solutions not only equaled them as, in some situations, even improved the proposed solution. The algorithm was tested and validated on the field, and although the results have already been presented in papers published in the last year by the authors of this paper, it is now presented with its mathematical formulation and comparison with the other solutions. This approach is expected to be able to improve (and even demystify) the process of pattern expansion and be the basis for future work in the continuation of the optimization process.

Jan 1, 2019

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Brian Stump, Chris Hayward

Blasting operations at one copper mine are studied in detail to examine the relation between blast design parameters and near-shot, in-mine, and regional seismic and acoustic observations. Five observational experiments, namely collection of blast design data, near source recordings, GPS synchronized video, near mine recordings and distant regional observations were performed during one week in August. A variety of seismic and infrasound instruments were installed near the shot, on the perimeter of the open pit mine, and at several locations up to 500 km distant. Time tagged video recordings were taken of several shots. Three shots were used in the preliminary analysis, a 350,000 lb pattern with long delays, a 60,000 lb pattern with short delays, and a 256,000 lb pattern with short delays. Maximum peak-to-peak amplitudes of the seismic signals in the mine are not a simple function of the total size of the shot, but are related to the pattern timing. Peak pressures have a less clear relation to peak pressure but match the relative amplitudes of spectra modeled from the pattern design. The predicted spectrum based upon a simple impulse model fits the observed spectrum for ground acceleration measured near the pattern and explains why in this case a pattern of 60,000 lb results in the same seismic disturbance as the 350,000 lb pattern.

Jan 1, 2002

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Jean M. Bouvet, Pierre M. Vuillaume

There is not just one ANFO: ANFO explosive behaviour depends significantly on the blasting conditions and on its physico-chemical characteristics. For instance, ANFO effficiency increases whereas AN porosity is higher and consequently loading density of the explosive is less. This can be argued against generally admitted ideas. Therefore, the efficiency of industrial explosives related to ANFO (for example "relative weight strength" or "relative bulk strength") is a tool that must be used with caution.

Jan 1, 1993

By W. L. Saunders

RBH Note: In the early days of drill & blast tunneling the jobs utilized large crews of drillers and muckers. Advance per round was limited (typically around four feet) but two rounds per 8-hour shift were expected, around the clock. The scene after a shot must have been chaos, with the muckers expected to quickly make space for the drill setup. Makes one wonder how much time was allowed for the smoke and fumes to clear. Note the headgear of the tunnelers.

Jan 1, 2011

By Tapan Goswami, Brent Geoff

Mining multiple steeply sloping coal seams introduces challenges in terms of safety and productivity. Work on steeply sloping surfaces for the processes of bench preparation, mark-out, drilling, loading and blast tie-up, coal cleaning and recovery is inherently hazardous. Furthermore, a large number of mining cycles is usually necessary, as small rounds are required and each layer is separately drilled, loaded, blasted and excavated. This exposes personnel and machines to additional risks and also incurs higher unit costs of mining as machine productivity is reduced. A case study is presented of a mine in New South Wales, Australia where three coal seams are separated by layers of inter-burden rock. Due to the unfavourable sloping nature of the coal seams the conventional practice was to drill and blast each layer separately.

Jan 1, 2010

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By Jody Todd, Ernesto Villaescusa, Ronald Lachenicht, Kelly Fleetwood

In the underground environment, characterisation of a rock mass during the mining cycle becomes increasingly difficult due to a lack of rock mass exposure for measurement or observation. In most cases rock mass characterisation occurs prior to mining by inspection and logging of exploration drill core, or prior to mass excavation through drive mapping for geological and geotechnical data. Characterisation strategies, if applied during the mining cycle, can reveal near-field anisotropies that may affect the behaviour of the rock mass with respect to excavation. These methods can aid in understanding the performance of stopes based on geometry, in-stope extraction sequence, and stress modelling. One such method of characterisation involves the use of production blast vibration monitoring and analysis as indicators of rock mass anisotropy through travel-time tomography.

Jan 1, 2008

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011