Search Documents

By Larry Schneider

In recent years, many individuals looking into the future of the blasting industry have predicted that the most likely next technological breakthrough would be the use of high precision, digitally controlled detonators. This seemed logical since not only was there much room for improvement in this area, but any significant improvement in delay timing could yield great benefits in productivity and control of adverse effects. And in fact, within the past two or three years, such electronic detonators have been introduced in the field by a number of different manufacturers. These systems are currently being used in many routine blasting operations around the world which are being closely watched and evaluated.

Jan 1, 2006

By Andrew F. McKown, Robert A. McClure

This paper will describe a trench blasting case history in close proximity to several adjacent structures, including a bridge abutment, railroad tracks, and utility pipes. Some design considerations involved in close-in blasting will be discussed, including allowable peak particle velocities and prevention of rock block movement. The importance of several trench blast round design factors is pointed out, including choice of explo sive to prevent propagation, maintaining a sufficiently high powder factor, and mucking out for maximum relief after every round. Vibration monitoring and good record keeping are shown to be important in order to evaluate blast problems and make modifications to round designs.

Jan 1, 1988

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Alan Hooper, James E. Mischler

Construction began in 1984 for a 5 megawatt hydroelectric power retrofit at the O'Shaughnessy Dam for the City of Columbus, Ohio. The construction necessitated excavation of limestone bedrock up to 27 feet below the normal water level of the river downstream of the dam. Proximity to the river and difficult terrain resulted in an interesting and challenging construction project.

Jan 1, 1986

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020

By Constanza Bujes, Mark Jones, Graham Crook, Yansan Jamyanbaatar, Sedat Esen

Tracking ore characteristics such as grade and hardness from its original position into the material handling and processing stages remains one of the key challenges in open pit mining of hard rock deposits. The most efficient technique for rock fragmentation and separation of ore from waste is blasting, which induces changes in the grade distribution by displacing the in-situ ore into a diggable muck pile. Material movement defines the post-blast grade distribution, which is key to optimising the value of the ore and accounting for ore loss and dilution. Techniques to directly measure the displacement in open pit mining have been implemented routinely and have provided calibration and validation data for blast models to build upon. The JK Value-Based Ore Control blast movement model (JKVBOC) is the latest development of a series of research studies into blast movement and ore control at the Sustainable Minerals Institute of the University of Queensland. The blast model discretises the bench into blocks, defines the initial velocity of each block based on the blast design, confinement and explosive properties, and simulates the displacement using a physics engine. Calibration and validation of the model has been performed in open pit hard rock mines in Australasia in diverse confinement conditions. This paper describes the calibration and validation of the blast movement model against direct measurements of blast movement and final muck pile shape for a case study where the displacement of multiple shots was modelled for an open pit mine, with an analysis of the implications for ore loss and dilution. A key finding in this study is the need for further integration of this technology into the existing systems for ore control, and the potential for applications in tracking ore characteristics other than grade into process control.

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Jay Smerekanicz, Florin: Pedersen Gheorghiu, Alan Cameron

In order to expand the capacity of Modern Landtill, a groundwater extraction system consisting of a linear system of pumping wells over 2,700 feet long had to be replaced. The new system would be covered by landtill cells to a depth of approximately 400 feet, and therefore would have to be maintenance free. In addition, the new system had to be proven to be more effective than the previous system, groundwater extraction had to be maintained during construction and construction could not disturb either the landfill operation or nearby residential neighbors.

Jan 1, 2001

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020

By C. T. Aimone-Martin, B. M. Meins

This paper compares response of large urban structures to small charge weight, ultra-high frequency rock blast excitation from contiguous excavation to that of houses to more distant, larger charge weight blasts. Time correlated responses were measured for both structures at the corners, top and bottom of the structures as well as in the foundation rock below the bottom. The comparison allowed the following conclusions: Close-in blasting with direct rock to building wave transmission imposes short wave length excitation which fails to excite the large, massive structures synchronously whereas the more distant blasts do synchronously excite houses. The larger urban structures respond predominantly in wave transmission mode where there is a noticeable difference in time, frequency, phase and amplitude of motions measured at the bottom and top corners of the structure. Excitation motions along the base of the larger urban structures also differs in time, frequency, phase and ampli-tude. The short wave length of the excitation motions leads to attenuation of the peak particle veloc-ity along the base. Ultra-high excitation frequencies, which are much higher than the expected struc-tural natural frequencies, lead to deamplification for all events for the large urban structures.

Jan 1, 2018

By John C. Brulia

The IME member companies, the ISEE along with its chapter organizations, the Federal, state and municipal regulatory agencies, and the industry consultants and suppliers have developed safety equipment, provided safety guidelines, promulgated safety-oriented regulations, and conducted safety training for blasting personnel in an effort to reduce explosives-related accidents.

Jan 1, 1994

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By Walter Voglauer, Elisabeth Zechmeister

Five serial photos show the first second of the demolition of a 75 m high, reinforced concrete tower in the 23rd District of Vienna, Austria. The tower demolition with high explosives was necessary because a 175t excavator could not finalize the destruction with mechanical tools. All mechanical works in preparation of the blast, such as the borehole drilling, were done by civil companies under the responsibility of the contracted demolition company PRAJO. The blasting itself was planned and executed by the engineer corps of the Austrian Armed Forces, Sunday, May 26, 2013. Nearly 800 boreholes filled with more than 100 kg of military plastic explosives were initiated with about 1,600 Austin electric delay detonators in exactly 1,000 ms and 30 steps of delay. The 10,000 tons of reinforced concrete tower fell as planned without any damage to the environment. Photo 5. The rest of the detonators initiate the water pools filled with high explosives forming a bizarre white water front to fight the following strong development of dust. The first 1,000 milliseconds are over.

Jan 1, 2015

By Diogo Fonseca, José Manuel, Nuno Fernandes, Blessing Taiwo

This research focuses on enhancing the synergy between blasting and primary crushing operations in quarries. A blast operation at dstgroup aggregate quarry in northern Portugal was simulated to fine-tune blasting techniques aimed at optimizing fragmentation indicators. The methodology involves conducting precise blast drill hole surveys, generating detailed terrain 3D models, and integrating these models into blast simulation software to enhance accuracy and optimize production efficiency. The study applies these simulations to test blasts, evaluating improvements in cost-effectiveness, crusher power consumption, and fragmentation efficiency using both aerial and terrestrial image analysis technology. The quarry key performance indicators (KPIs) guide the blast design simulations, ensuring practicality and relevance. The case study blast revealed that implementing optimum blasting techniques can enhance crusher throughput, reduce operational costs, and improve safety. This paper is part one of a three-part technical series where we aim to create a sampling procedure and establish a reliable baseline for the current state of operation. This baseline will be used in subsequent follow-up technical papers to make recommendations and improvements. The outcome of this study provides a framework for quarry operations seeking to enhance their efficiency.

Jan 21, 2025

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur. Two recent render-safe operations conducted in and around urban environments dealt with deteriorated, sensitive dynamite and damaged blasting caps. Utilizing innovative neutralization chemicals and processes to render-safe the deteriorated dynamite, while protecting the general public, proved to be the safest, most environmentally responsible and cost-effective way to approach the problem. In both cases, the explosives, old dynamite and detonators were found in abandoned, unlocked magazines. The dynamite was in a significantly deteriorated state, which was evident due to the nitroglycerine found leaking in,around and under the dynamite cartridges. Iron wire permissible electric blasting caps were also found in a corroded condition with exposed explosives and un-shunted lead wires. With occupied buildings within 180 feet (54.86 meters) of the magazines, any procedure (e.g. transporting, countercharging, burning) that could potentially cause a detonation was not an option. In the event of an unplanned detonation during neutralization operations, several blast mitigation methods were employed to safeguard the site. This operation and a similar one with over 1,000 pounds of crushed and buried leaky dynamite were unique since all the explosives were rendered-safe and neutralized on site. The use of advanced neutralization products and filtering processes allowed for a safer, more environmentally responsible way to resolve the problem. The magazines and all residual solids and fluids were tested and confirmed by independent labs to have no explosives residues. The effluents were treated on site, tested and met safe levels, so they were disposed of at a local municipal wastewater facility.