Search Documents

By Diogo R. Prado, José Aurélio M. da Luz

Drying operation can have a major importance in a mineral processing undertaking. The proper sizing of dryers can ensure the specified dewatering level without energy wastage. However, often the sizing of fluidized bed is done disregarding the actual residence time distribution (RTD) of the particles inside the reactor. In this case it is usual to adopt the average residence time as a design criterion. In this work, we have quantified the effect of residence time distribution on drying, ensuring that a previously adopted fraction of the particles remains inside the reactor for the required time lapse needed for drying. Design criteria such as particulate flow rate and drying time, taking into account the statistical distribution of residence time was studied, matching the thermodynamic and fluid dynamic aspects of the drying process. Experimental tests carried out have confirmed the RTD for a teetering bed as the same for a canonical ideal mixing system. Although the fluidized bed volume using the proposed formulation was higher than that found for the average time based procedure, the efficiency gain in drying has proven advantageous.

Jan 1, 2014

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By N. Vasumathi

Most of the Iron ore washing plants set up in India in the earlier days consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers. In this classical approach, iron values were lost in the form of fines and ultrafine into the tailing ponds as they had little commercial value in those days and accumulated in huge quantities over the years. As the high grade deposits are getting exhausted and the demand for high grade finer material for pellet making is ever increasing, focus is shifting towards recovering the values from the erstwhile tailing ponds by column flotation. This is also supposed to mitigate to a certain extent the environmental problems caused by the ever expanding and unmanageable tailing dams. A case study is presented wherein a composite sample is prepared from samples drawn systematically from multi - locations in a sprawling tailing dam. Laboratory scale column flotation tests on this composite tailings sample, basically originating from two operating iron ore beneficiation plants of JSW Steel Ltd., one of the leading producers of steel in India are found to be encouraging. Desliming followed by reverse and cationic flotation tests using flotation column resulted in the concentrate of 61.88% Fe, 4.81% SiO2, 2.52% Al2O3 and 3.30% loss on ignition (LOI) from the tailings analyzing 57.86% Fe, 7.10% SiO2, 3.52% Al2O3 and 6.14% LOI with 52% weight recovery. The causes for the quality improvement could be attributed to desliming of un-liberated ultra fines of kaoline and hydrated iron oxides and their further reduction by efficient flotation process. The process and the cationic collector developed for this purpose are adopted in the new flotation plant created to treat these tailings. Keywords: iron ore, washing, ultra fines, tailings pond, column flotation

Sep 1, 2012

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By Skinner. W.

"Introducing cutting-edge development work, which aims to simplify mineral processing flow-sheets, reduce costs and address environmental issues. Over the past four years Innovative Mineral Processing Technologies Pty. Ltd (IMPTEC) Australia have developed a Super-fine Crusher and a Planar Magnetic Separator which offer low cost, wet or dry alternatives to conventional grinding and conventional magnetic separation. Each of these machines has been successfully trialed at pilot scale and are now in the process of transitioning to commercial scale. This paper reports on the progress made in each of these fields. The potential scope for application of super-fine crushing technology as an alternative to grinding is potentially expansive and could include beneficiation of metalliferous ores, precious metal ore processing, hydrometallurgical processing, industrial minerals and coal processing, plastic fillers and ceramics processing as well as processing of cementitious slags and fly-ash. IMPTEC have recently achieved outstanding results at pilot scale with a dry combination of super-fine crushing and planar magnetic separation, which offers an alternative to the wet processing of magnetic iron ores. The dry combination has set new laboratory performance benchmarks when compared with the industry standard wet Davis Tube Tester. The test results have also established a strong evidence base showing that super-fine crushing achieves liberation of value minerals at coarser sizes when compared with grinding. The dry combination of super-fine crushing and planar magnetic separation also addresses environmental issues and completely eliminates grinding. An IMPTEC super-fine crusher is currently undergoing commercial trials, generating ultra-fine products from granulated lead blast furnace slag for use as cement substitutes. The performance of the super-fine crusher on this extreme duty highlights the potential benefits of super-fine crushing over the wide range of industries and applications where conventional grinding is employed.INTRODUCTION Present day mineral processing practices can become anchored in convention, where, inefficient methodologies are recognized and accepted as “best practice” or “industry standard”. Motivated by this challenge, IMPTEC has undertaken the development of radically different and improved methodologies in the fields of fine comminution and magnetic separation. Whilst, crushing is much less energy intensive and generally less capital and maintenance intensive than grinding, the technology has stalled due to the lack of crushing devices, which have the capacity to adapt to fine and ultra-fine duties. Grinding practice advances have been achieved through major increases in machine size and power. However, these advances are also accompanied by major escalations in capital, operating and maintenance costs. The economics of this strategy has become increasingly questionable. A typical example is the viability of low-grade magnetite beneficiation, which can hinge largely on the cost of grinding to fine and ultra-fine liberation sizes."

Jan 1, 2018

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By S. V. Bogdanov, S. I. Grishaev

"The article presents the materials about the appropriateness of the use of rental indices to assess the effectiveness of the use of deposits of rare earth elements (REE). The authors suggest from the standpoint of rent payments to rate for the owner the possibility of using the anticipated rental income as the indicator for the analysis of preferences and economic significance of enrichment of extracted raw materials in the emerging field of rare earth metals (REE). Usually from ore mined at the fields, for flotation technology to produce concentrates with collective REE, then they are subjected to chemical-metallurgical processing of the received products are divided into pure oxides, chemical compounds or isolated from them pure metals and alloys. This commercial product is shipped to the buyer. REE were a non-renewable natural resources, so the calculations for determining differential and specific rent showed that during the development of the technologies of mineral processing of a specific field it is necessary to consider what the expected rental income depends on the magnitude of differential rent is related to the volume of production of REE for the whole planned period of exploitation of natural resources. This income is determined by the amount of stock field. For long-term exploitation of the deposit is observed in almost direct proportional dependence between the annual differential rent and the rental income. The decrease in rents in the long run is determined by the change in the composition of ores included in the extracted raw materials and the balance between light and heavy REE. The largest 70% reduction of the rent projected for ""cerium"" fields, while for ""yttrium"" these losses are considerably smaller. Tomtor, Chuktukon and Katuginskoye Russian deposits are characterized by a level of rent that is comparable to the mastered foreign sources of REE. Thus, the enrichment of minerals with REM in the domestic deposits is quite competitive at the world level. INTRODUCTION Deposits of rare earth metals (REE) are non-renewable resources that should be developed and used so that it would be possible to provide a reduction due to payment of appropriate resources for future generations. This compensation, due to the reduction of natural resources, can be carried out both in natural and in economic terms (1). When analyzing economic compensation options, particular attention should be paid to rental income in assessing the attractiveness of using different REE deposits. It is known that absolute and differential rents are summands when calculating the value of natural rents. The value of the absolute natural rent is proportional to the unit price of the product obtained from mineral raw materials and sold on the commodity market. Limitations, as well as the use in production processes and business, contribute to the gradual reduction of natural resources, which increases their consumer value and affects the price of commodity products from primary raw materials."

Jan 1, 2018

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By J. K. Wen

The Mojiang nickel deposit is situated in Mojiang county, yunnan province, a tropical area in the southwestern China. The known geological resource (measured and inferred) includes 4 million tons of nickel sulphide ore at an average grade of 0.50% Ni and 0.34% As. Nickel minerals are mainly gersdorffite (NiAsS), millerite(NiS), morenosite (NiSO4?7H2O), and more than 50% nickel minerals is gersdorffite which contains arsenic. Pyrite is the dominant sulfide mineral, 22% in the ore and part of nickel minerals are locked in pyrite. It is difficult to attain the nickel concentrate quality allowed by a smelter and the acceptable nickel recovery through flotation due to the high arsenic in the ore and the nickel minerals locked in pyrite. The shake flask tests and column tests for nickel recovery from the Mojiang nickel sulfide ore had been finished by the end of 2003. The column bioleaching tests were carried out using the columns with diameter of 120 mm and height of 1200 mm, and 70% of nickel dissolution was attained in 300 days. A 10,000t pilot test heap was built in the Mojiang Nickel Mine by June 2003. The ore used in the test heap was supplied from the underground mine and was crushed to -20 mm before being feeding to the test heap, which is 4~5 m high, 30 m wide and 50 m long. The naturally adapted mesophile and moderate thermophile have been inoculated into the leaching pile by June 2003. The operating temperature in the heap ranges from 38? to 55?, varying with season. 30% of nickel dissolution was achieved in 3 months and the typical pregnant leach so-lution (PLS) contains 2~3 g/L Ni and 20~30 g/L Fe. The Ni sulfide which was produced by us-ing Na2S 10 t/t?Ni contains 16%~20% Ni and Ni recovery was 98%. 70% of Ni dissolution is expected in 12 months. The test heap was scaled up to 60,000 t of ore per year by mid of 2005. In this paper metallurgical studies and performance of the pilot test heap will be described. The results of mineralogy, shake flask tests and column tests on bioleaching of the nickel sulfide ore are reviewed. The key test heap operation parameters, the performance of bio-heap leahing-Na2S precipitation, ferrous oxidation-ferric precipitation-Na2CO3 precipitation, bacteria in the pile, water and acid balance, effluent disposal, capital and operation costs are also discussed.

Jan 1, 2014

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By Ashiwani Kr Gupta

The floatability of coal is affected by the presence of dissolved inorganic ions in plant process water. Water quality is characterized in terms of conductivity, hardness, turbidity and composition of oil. These quality indices are correlated with coal flotation performance for three different water named, ?R&D laboratory tap water?, ?process untreated water? from West Bokaro wahsey-2 Tata Steel, India and ?process treated water? after passing laboratory developed treatment process. The study clearly indicated that a significant quantity of clean coal is being lost due to poor process water quality used in the flotation process. The laboratory investigations showed that if these dissolved salts and suspended solids are reduced to even 50%, a clean coal yield improvement by minimum 5%~10% at the same ash level could be expected. Therefore, the conventional practice of water recycling though a thickener or a tailings pond needs a complete re-look. The water treatment process for recycled water has also been discussed for improving the process water quality as well as enhancement in flotation performance efficiency.

Jan 1, 2014