Search Documents

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By F Battaglia-Brunet, D. H. Morin, Foucher S. ’

In the mineral-processing field, bioleaching of metal sulphide concentrates is currently operated in very large mechanically agitated tanks. Such bioreactors have considerable requirements in terms of power consumption for mixing, aeration and heat transfer. The use of slurry bubble column, where the particles are suspended by gas motion as well as by liquid upward flow, could be an alternative to achieve bioleaching in more economical conditions. In order to compare these two techniques, a unit of stirred reactors in cascade and a bubble column were comparatively operated at laboratory scale in the bioleaching of a pyrite concentrate. For both pieces of equipment, experiments were performed not only in batch mode but also in continuous conditions.

Jan 1, 2003

By Jeremy Bosman, Niel Lourens

"Cyclones are used in four main applications in primary wet heavy mineral processing plants i.e. upfront desliming, densifying, and concentrate stacking and tails deposition.UPFRONT DESLIMINGMany heavy mineral ore bodies are associated with high slimes varying from 15 to 60%. The increased viscosities arising from the slimes impact negatively on heavy mineral recovery in the spiral plant. Recoveries can be reduced by up to 10%. Cyclones have proven to be able to remove slime efficiently with acceptable loss of valuable heavy mineral in the overflow. For low slime applications, typically below 25%, it is possible to achieve the desired results using a single stage of cyclones, whilst for higher slimes, two stages of cyclones are required. The overflow of the primary stage is retreated through a second stage to minimize heavy mineral loss."

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003

By M. T. Spyridopolous, S. J. Neethling

"There has been a significant research interest in the stability of single thin films, including prediction of their failure based on disjoining pressure and film thickness experiments and DLVO theory. It is, however, notoriously difficult to correlate information on the failure of a single thin film with measurements of foam stability. This is particularly true for the prediction of dynamic foam stability indicators, such as equilibrium froth height and surface bubble size.An alternative experimental approach to studying single thin film failure for predicting foam stability is to measure directly the coalescence probability between two approaching bubbles in a surfactant solution. These experiments can be performed under different chemical and physical conditions by using a micromanipulator that allows variation of bubble size, surfactant concentration, approach velocity and stationary position. The interface radius of curvature, the time to coalescence and the film area between the bubbles can be measured directly using image analysis.In a foam, the force exerted on the thin film separating two bubbles depends on the local radius of curvature of the Plateau borders and vertices, which depends in turn on the local liquid content. Results from different bubble sizes in the micromanipulator therefore translate into regions of different liquid content in the foam. Small bubbles, having a high radius of curvature correspond to the low-liquid content (Polyhederschaum) region higher in the foam, and large bubbles to the wetter (Kugelschaum) region closer to the liquid-foam interface. Experiments with different holding distances between the bubbles correspond to differences in bubble size in the foam, as the size of the film between the bubbles varies."

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St.-Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By Jian Zhang, Yongfu Yu, Fuguang Zhang, Liping Che

There is one large-scaled iron ore deposit in Inner Mongolia of China, but it is very complex which includes about 170 types of minerals and 71 elements. The hematite, magnetite are mainly iron ores. It is difficult that the iron mineral can be separated efficiently by common dressing methods due to the complexity, and the iron concentrates in the mineral processing factory contains many foreign substance such as K, Na and Si so that the process in iron mill is influenced because of the foreign substance, so it is vital reducing the foreign substance.

Jan 1, 2003

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of some silicate minerals (i.e., feldspar, quartz and wollastonite) after contacting different triboecharging medium made of different materials were studied. The charge acquisitions by different size fractions of minerals were monitored and accordingly the energetic work function values, i.e., the main parameter determining the entity of triboelectric charges acquired by mineral grains, of the examined minerals were estimated. Moreover the separation behavior of different size fractions of these minerals through the electric field of a laboratory free-falling separator when the mineral grains are charged by different tribochargers were observed and considered as the electrical separation potential of the examined minerals.Furthermore, the role of adsorption of different chemical species on triboelectric charge characteristics and charge acquisition of mineral samples were described from theoretical point of view and the effects of some chemical reagents on triboelectric charge acquisition of the examined minerals were studied. In addition the separation behavior of chemically conditioned quartz, feldspar and wollastonite minerals, using different anionic and cationic reagents, through the electric field of a free-fall electrostatic separator before and after chemical conditioning were monitored.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing mainly of feldspars, quartz, and wollastonite. Different separation tests under various conditions were conducted to this complex silicate ore. Before passing through the separation device, the ore sample was conditioned by different cationic and anionic reagents and then was triboelectricaly charged by different tribocharging medium in order to find the effective reagent and tribocharging medium for separating silicates. Besides the role of temperature and humidity of the surrounding ambient in separation behavior were considered."

Jan 1, 2003

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By K. A. Natarajan

Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.

Jan 1, 2003