Search Documents

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Anthony L. Reynolds, Clifford J. Wren

"The adoption of a significant pile testing regime, the use of Eurocode 7 as the design standard, the development of lean construction techniques, and lateral thinking in overcoming some considerable construction challenges allowed Stent Foundations to construct the foundations for the new Wembley Stadium, London, on time and within budget. In addition to the piling works for the main stadium, and after significant design development, a large number of extra piles were required to raise the new iconic roof Arch to its final position some 133 metres above the ground. A 1,400m long contiguous bored pile wall was also constructed to allow for excavation and formation of the new pitch. INTRODUCTIONHjstorjcal lntrodyctionWembley Stadium is the 'home of English football'. As long ago as the 1880's, Wembley Park leisure grounds had football pitches and running tracks.In 1918 the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Exhibition area covered 219 acres and the area on which a former abandoned tower called Watkins Folly had stood was chosen as the site for the new stadium (http://www.wembleystadium.com).The Empire Stadium, as it was originally known, was designed by architects Sir John Simpson and Maxwell Ayerton and the engineer Sir Owen Williams. It took just 300 days to complete at a cost of £750,000 ($1.4m), and was built using 25,000 tons of ferro concrete, 1,000 tons of steel, and over half a million rivets.The Empire Exhibition was a remarkable event, containing fountains, lakes, gardens, and many pavilions, each representing the architectural style of the countries exhibiting. It was opened on 23rd April 1924 and the final attendance was over 27 million, with 4.5 million admissions to the Empire Stadium alone."

Jan 1, 2005

By Richard Pizzi

Built in 1806, Boston's African Meeting House is the oldest surviving Black church building in the country. A $7 million dollar renovation was begun in 2006 to restore this historic building to its 1855 appearance and to modernize the building's accessibility, electrical and mechanical systems. As part of the restoration, an underground utility room and elevator tower, needed to provide handicap access to the Meeting House, were constructed. Extending up to 17 feet below the foundations of the abutting buildings, the utility room was constructed within one foot of some of Boston's oldest and most expensive residences. All equipment and materials had to enter the work area through a narrow alley rendering conventional methods of excavation and construction of earth support using heavy equipment unfeasible. A unique combination of micropiles, structural cap beam, internal struts and shotcrete facing was designed and constructed to provide the permanent and temporary support of the lateral loads from the earth pressures and adjacent building surcharges and the vertical loads from the elevator tower. The narrow and congested streets of the Beacon Hill neighborhood presented many day-to-day challenges for the contractor.

Jan 1, 2011

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010