Search Documents

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By Aly M. Mohammad

The Delaware River Tramway will link civic and retail developments in Philadelphia, Pennsylvania and Camden, New Jersey. Twin 300-foot towers will anchor the cables at either side of the river. Four high capacity drilled shafts designed by the Geotechnical Department of DMJM+HARRIS support each of the towers. At the Philadelphia tower, each 6-foot diameter shaft extends 130 feet deep and terminates with a 30-foot rock socket. The shafts are situated within the footprint of an existing relieving platform, which complicates the typical construction sequence. Also, the subsurface conditions at the site provide a unique challenge in both the design and construction of the drilled shafts. During the construction of the four-drilled shafts for the Philadelphia tower, a 6000-ton Osterberg load test was performed on the first shaft to verify design assumption and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics and develop foundation design parameters suitable for the site conditions. By doing so the Design Engineer was able to reduce the length of the rock sockets on the remaining production shafts by approximately 5 feet per shaft. As a result, the test provided a significant cost saving to the Owner by eliminating 15 feet of rock drilling from the construction costs. This paper presents a description of the unique design and construction methods adopted for the foundations, also on the Osterberg load test including equipment used, number and locations of strain gages, and interpretation of results. The results and findings presented in this paper could benefit both the design and construction industries because it provides a comparison between geotechnical design assumption and actual field measurements; which has always been a challenge particularly for rock formation.

Jan 1, 2002

By R. G. Horvath

In the Hamilton area, and in many other areas of Ontario and around the world, large diameter drilled pier (caisson) foundations are frequently selected as the most appropriate foundation system for heavily loaded structures. Locally, these drilled piers are typically founded in competent glacial till or in the underlying shale bedrock depending on the anticipated design loads. Drilled pier foundations socketed into shale bedrock were selected for the Hamilton General Hospital Addition. The structural loads applied to socketed pier foundations are supported through shaft resistance, which is the shearing resistance developed along the vertical pier-rock interface, and by end-bearing resistance. The factors which control the load-displacement-time behaviour of socketed pier foundations are the strength and deformation characteristics of: a) the concrete pier, b) the rock mass, and c) the interface between the concrete pier and the rock.

Jan 1, 1987

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Dilip Khatri

Helical pile anchors have gained acceptance over the past sixty years. Most recently they have been commonplace in the 20th century for the power utility industry in anchoring transmission towers, equipment platforms, street lighting, telephone poles, and radio tower applications. They have a strong proven industrial track record in these industries. As the cost of conventional deep pile foundations rises, the practical benefits of helical pile anchors becomes evident as a practical alternative. Noted for their uplift capacity, helical piles demonstrate equally strong compressive capacity as a structural foundation element. This paper summarizes the history, practical benefits, and technical requirements for helical piles. Significant structural testing has been completed at various universities. The practical benefits of these tests are discussed. One case example of proven performance is presented to demonstrate the advantages and disadvantages of helical pile anchors as suitable foundation elements.

Jan 1, 2003

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011