Search Documents

By Takeru Fukaya, Tsutomu Namikawa

"The bending tensile stress occurs in the ground improvements when external forces are applied to the column and wall shaped ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements rationally.Three points bending tests are conducted to investigate the bending tensile properties of cement-treated soils in this study. Cement-treated soils mixed in a laboratory are used in the bending tests. The test specimens are prepared with the several mixing properties to study the relationship between the tensile properties and unconfined compressive strength qu. Bending tensile strength Tfb and fracture energy Gf of the cement-treated soils are evaluated from the load-deflection curves obtained from the bending tests. The experimental results indicate that Tfb and Gf are approximately proportional to qu.INTRODUCTIONThe ground improvement by deep mixing has been widely used for structure foundations, retaining walls and liquefaction mitigations. Recently column and wall shaped ground improvements by deep mixing method have been applied for economical reason. When external forces are applied to the column and wall shaped ground improvements, the bending tensile stress occurs in the ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements appropriately.Namikawa et al. (2007) conducted the finite element analysis to investigate the dynamic behavior of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, an improved ground consisting of several grids in a line was chosen to study the basic behavior of the lattice-shaped improved ground. Fig. 1 shows a example of calculated tensile failure zones in the improved soil during the earthquake. Half of one section of the improved soil consisting of two grids in a line for the 8 m × 8 m grid was modeled in the case. In Fig. 1, the failure occurs at the bottom and upper corners of the improved soil grid. The analysis result indicates that the constitutive model which can appropriately evaluate tensile failure behavior of cement-treated soils is required to evaluate the performance of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, the elasto-plastic model developed by Namikawa and Mihira (2007) was adopted for the cement-treated soil behavior. The elasto-plastic model can suitably describe the tensile failure behavior of cement-treated soils. In the elasto-plastic model, tensile fracture energy is adopted to determine a tensile softening relationship because it is difficult to directly measure the stress-strain relationship after the peak stress state in direct tension tests. However there is little experimental study on the tensile fracture energy of cement-treated soils."

Jan 1, 2015

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Terzis D. PhD, Katterbach M.

While awareness around the environmental impact of existing grout materials and chemical binders is increasing rapidly, biotechnologies are growing traction as sustainable alternatives in groundwork operations. Herein we present the principles and application methods of bio-grouting. The term is used to describe a system which is based on soil, groundwater or marine enzymes which are able to catalyze the production of calcite replicating a natural phenomenon. The system’s end result are mineral crystalline bridges which act as binders to improve the geotechnical properties of soils. This paper presents a comprehensive description of bio-grouts, their underlaying mechanisms contributing to mineralization as well as environmental considerations. With their water-like rheology, bio-grouts have a wide application range and are minimally invasive, requiring only very limited injection pressures. The equipment is the same as that used in conventional cement grouting, and the reactant components are worldwide available or easily suppliable, which explains why bio-grouting has nowadays become a valuable and sustainable alternative towards efficient soil treatment. Recent developments in the last years have allowed to further increase the applicability and efficiency of bio-grouts to ultimately bridge the gap between research and practice. A case study is illustrated in this paper showing the successful implementation of bio-grout for the stabilization of weakly cemented sandstone to safeguard an adjacent road segment in Switzerland

May 1, 2022

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let's say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By Jim Bruce

This paper presents details of a slope stabilization scheme built in late 2003 at a 16m-high railway embankment in southern Ontario, Canada. The owner, faced with continuing maintenance and safety issues arising from numerous nuisance slides, and residential neighbors in close proximity to the slope, sought new proposals to replace a previous recommendation to cut down all trees and undertake a deep soil nailing scheme. A non-reticulated micropile array with surface cap beam was proposed and built on the south side of the embankment with no tree removal required. A detailed FLAC analysis was completed, using multiple iterations to arrive at the eventual, optimized micropile depth and spacing. Analysis predicted an 18% increase in the factor of safety. Short term inclinometer monitoring and performance evaluations in the months since construction so far corroborate the prediction.

Jan 1, 2004

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001

By Chul Soo Park, Juhyung Lee, Duhyun Baek

"In this study the preliminary design of suction pile as the supporting system of the concrete floating structures was performed at the offshore pilot project area in Korea. The suction pile of the floating structures has to satisfy the lateral resistance against external force evaluated from the marine and structure conditions, as well as the penetration ability according to the soil and seepage conditions. In the design, the required penetration depths for lateral resistance were evaluated with different diameters of cylindrical steel suction pile, and the design suction pressures at each penetrating depths were assessed through the comparison of penetration forces and penetration-resistances. Finally, the optimal dimension of suction pile for the pilot project area was proposed.IntroductionInterests in sea spaces have rapidly increased around the world due to limitations in use of lands. Such increase has resulted in construction of numerous marine structures aimed at expanding the use of sea spaces and developing marine resources. South Korea also needs to secure construction technologies for floating infrastructures on its relatively deep seas. Foundations for floating structures consist of anchors and mooring systems rather than driven piles or cast-in-place piles, due to limitations in equipment operation or economic feasibility. Anchors and foundations used on the sea include drag anchors and suction piles, but the suction piles are more widely used for reasons regarding uncertainties of calculation of bearing capacity and construction. Large-diameter suction piles are generally used to utilize fully their penetration ability, which is proportionate to the square of the foundation diameter, and the length-diameter ratio (L/D) does not exceed 6 (Randolph et al., 2005; Andersen et al., 2005). Recently, a design and construction technology using group suction piles consisting of medium-diameter suction piles and concrete pile caps is being developed as an alternative to the conventional large-diameter mono suction piles. In addition, pilot projects involving the group suction piles of mediumdiameter are currently being reviewed for the southwest coast area in Korea. In this study, therefore, preliminary design for installation of medium-diameter mono suction piles as the supporting system of the concrete floating structures was performed, and suction pressures, penetration forces and resistances, and lateral loading capacity with diameters were reviewed."

Jan 1, 2017

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By Donald T. Robertson

This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.

By Donald T. Robertson, Kurt Hecht, Michael K. Muchard

"This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.INTRODUCTIONDynamic testing of driven pile foundations was originally developed in the late 1960’s and commercialized in the early 1970’s. While the methods of analyzing dynamic test data have improved with the advancement of computer technology, the test method and the sensors used to acquire the data have changed little. In 1998, under a research grant provided by the Florida Department of Transportation, (McVay et al, 2002) an Embedded Data Collector system (EDC) was developed. The collector utilizes two sensor packs, each consisting of one strain gage and one accelerometer, embedded near the pile toe and pile top. Utilizing the toe sensor pack, the system provides reliable real time pile end bearing capacity measurements. This end bearing capacity is combined with a Case Method Solution augmented with an automatic damping calculation to provide the overall pile capacity, pile skin friction capacity and pile end bearing capacity. Also, since the gages are embedded, they have the ability to track all changes from the casting yard (i.e. prestress), driving, and subsequent setup (freeze, relaxation, etc) at both the top and bottom of the pile."

Jan 1, 2017

By Dave Paul

Dam rehabilitation involves a range of design, construction, and operation risks, some of which are not encountered in new dam construction. These risks can have significant impact on project schedule and project budget. Owners, engineers, and contractors need to understand these risks. Existing dams typically were designed in an era of design and construction standards that have been upgraded and changed. Modern standards will impact the construction approach taken and involve understanding the earlier standards. Knowledge of historical standards/practices as well as current design standards and construction methods is valuable for developing and designing rehabilitation components. Construction records and as-built drawings are valuable when they are available. Rehabilitation projects often consist of older projects where as-built documents or construction records are not available. Where these records exist, many (most) times, they do not fully reflect the current conditions within the dam and appurtenant works. leading experienced practitioners to “expect surprises” both during investigation of the existing facility, as well as during construction. “Surprises” should be expected even when historical records of investigations, design and construction are available. Unknowns, be they known unknowns or unknown unknowns, can be planned for by developing an approach for the design and construction process to identify potential issues/problems, or at least alert the designer and contractor of potential issues. A Risk-Based approach applied for the entire life of the rehabilitation project can be used to alert the parties of potential “surprises” and provide direction for mitigating issues as they arise. This type of approach is particularly effective when the process includes senior practitioners with decades of design and construction experience in all aspects of dams. Minimizing impacts created by “surprises”, particularly during construction, can result in an improved project meeting budget and schedule goals and design standards. This paper identifies and categorizes risk types salient to dam construction, reviews the process of risk identification and analysis, discusses guidelines for risk allocation, reviews strategies to mitigate risks, presents several case studies where risk mitigation strategies were employed successfully (or unsuccessfully), and presents lessons learned. The paper concludes with a summary and recommendations for best practices for Project Risk Management and mitigation that can be used by: Owners; Design Engineers; and Construction Managers, in planning, design, pre-construction and construction phases of dam related projects.

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017