Search Documents

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By K. P. Wright

"Twenty-five years ago, there were about thirty-two gold mines operating in Canada; nine of these have been in continuous operation since then and are still operating. Three of these are part of the Dome Group. Operations of these three and of the newer mines in the Group are referred to in discussing process development over the last twenty-five years.Of the Dome Mines Group, Dome Mines Limited, Sigma Mines (Quebec) Limited, Campbell Red Lake Mines Limited, Detour Lake Mine and Kiena Gold Mines Limited, three have been in continuous operation for the last twenty-five years. Dome has operated for seventy-seven years; Sigma about to complete fifty years, and Campbell approaching forty. Overall, milling processes are virtually the same as they were twenty-five years ago. Tota1 go1d production from the three mines has hardly changed; 1960 production, 416,700 ozs. versus 411,300 in 1985. Milling costs have risen by a factor of six or seven and gold price from $35/oz. in 1960 to $322 in 1985.Basic flowsheets are relatively unchanged. Sigma is an all cyanidation mill grinding in cyanide solution; Dome operates gravity concentration and cyanidation; Campbell gravity concentration, flotation, roasting and cyanidation. All three use Merrill-Crowe zinc precipitation.Detour and Kiena are two examples of the major change in gold processing in the last twenty-five years - carbon-in-pulp. This process has brought along with it other changes, such as, carbon stripping and reactivation, electrowinning, and induction furnace melting. Modern mill design with its use of outside thickeners and agitators, bulk handling of reagents, instrumentation, etc., has made a radical change in operating conditions and appearance of the new plants."

Jan 1, 1987

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By Niklas Willemsen

Introduction to SVCs ? SVC = Static var Compensator ? Dynamic step-less control of reactive power without switching of passive components: ? Voltage control/stabilization ? Harmonics- and flicker mitigation ? Dip mitigation ? Main components: ? TCR (Thyristor Controlled Reactor) ? Tuned harmonic filters ? Control- and cooling systems ? Typical applications: ? Mine hoists ? Large mining complexes ? EAF, SAF, rolling mills, wind/solar farms etc..

Aug 1, 2013

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy joint venture in Madagascar is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behaviour and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behaviour of iron.RÉSUMÉ Le minerai latéritique traité par l’entreprise commune Ambatovy au Madagascar contient principalement de la limonite, composée de 40–45 % en poids (wt%) de fer (Fe) et de 1,1 wt% de nickel (Ni). Le procédé choisi pour le traitement de ce minerai tenait compte du comportement et du maintien du fer à chaque étape du schéma de traitement commercial. Parmi les facteurs pris en compte figuraient les récupérations de nickel et de cobalt, les consommations d’agents réactifs, les caractéristiques de séparation des liquides-solides ainsi que la pureté des produits semi-fini et final. Cet article compare les résultats des trois premières années d’exploitation commerciale à Ambatovy aux paramètres d’étude, en insistant notamment sur le comportement du fer.INTRODUCTIONThe main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. Ambatovy ore is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The nickel content of the ore is approximately 1/40th that of the iron content by weight; therefore, successful recovery of nickel depends on close control of the behaviour of iron in the selected process.The Ambatovy area is located 80 km east of Antananarivo, the capital of Madagascar. Exploration dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment, and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy nickel project. Dynatec became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan, Alberta (Collins et al., 2004, 2005; Collins & Vardill, 2005; Collins, Buban, Holloway, Masters, & Raudsepp, 2009). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement, and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy nickel project, in 2007. The current Ambatovy joint venture consists of an integrated nickel and cobalt mining, processing, refining, and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner), and KORES (27.5% owner)."

Jan 1, 2017

By Engineering Staff

"This paper briefly describes the surface mining operations at Smoky River Coal Limited (formerly McIntyre Mines Limited, Coal Division) near Grande Cache, Alberta. Geology, mining methods, equipment, manpower and reclamation and environment topics are discussed. Introduction Smoky River Coal Limited, a wholly-owned subsidiary of McIntyre Mines Limited of Calgary, Alberta, produces a high quality, low sulphur, low volatile bituminous coking coal from its minesite located at west central Alberta, approximately 20 km from the town of Grande Cache and 360 km west of Edmonton (Fig. I). Most of the coal property is contained within a 30 km long by 20 km wide block lying in a northwest-southeast direction in mountainous terrain. Elevations vary from 920 m above sea level ·at the plant·site on the Smoky River to 1,600 mat the upper levels of current and proposed mining operations. A total of 11 coal seams have been identified. Only two seams, No. 4 Seam and No. 10 Seam are currently considered of major commercial value. These seams are recovered by both surface and underground mining. Approximately 650Jo of the plant feed coal is obtained from a conventional shovel/truck surface mine; the balance is mined underground by room-andpillar methods. Background In 1921, McIntyre Mines Limited acquired some 26,300 hectares of coal leases at Smoky River. Since then the leases were explored intermittently by different companies including McIntyre. In the mid-l 960s exploration activities increased and several feasibility studies were completed. Development of the area was undertaken by McIntyre in 1968 and, in August of the same year, a long-term contract was signed with a consortium of Japanese steel mills for delivery of 2 x 106 t of clean coking coal for 15 years commencing in 1970. Production was focussed on underground mining, using longwall methods."

Jan 1, 1985

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By Dr. G. R. Hoey

"Abrasive wear and corrosive wear of carbon-steel grinding balls occurred simultaneously during the wet-grinding of hematite iron ore, and Ni-Cu sulphide ore, in laboratory ball mills. Two corrosion control methods, the use of corrosion inhibitors and pH control, were investigated and found to be effective means of reducing or preventing corrosive wear. Up to 50 % reduction of total ball wear resulted from the use of these methods.Corrosive wear is caused principally by the reaction of oxygen in air with the carbon-steel grinding balls, probably by the following reaction: 2Fe + O2 + 2H20 - 2Fe2 + 40H-.IntroductionA survey of corrosion problems in Canadian sulphide ore mines was completed and the findings were published in 197l(l). The corrosion survey was used to develop the present research program with the objective to find more economical and effective ways and means to reduce the corrosion that occurs in the mining and metallurgical industry. The purpose of this presentation is to review the projects being done by staff members of the Corrosion Section, Extraction Metallurgy Division, on corrosive wear and its control in wet-grind ball mills.Both abrasion and corrosion contribute to metal consumption during wet grinding of ores. The total wear of grinding media in this study is assumed to be equal to the sum of corrosive wear and abrasive wear. A great deal of research and development has been reported in the literature on ways to improve the abrasion resistance of grinding media but only a small number of studies has been reported on the corrosion resistance of conventional grinding media."

Jan 1, 1974

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

On the recent trip from Vancouver to Calgary with the President, Mr. C. C. Huston, and yourself, I had the opportunity of outlining a plan based on the following: Among the aims of the Institute are, obviously, the fostering of the confraternity of those engaged in the technical and management fields of the mining and petroleum industries. This may be achieved in a number of ways, of which, to me, the interchange of ideas and experience between different parts of Canada and different sections and divisions of the Institute appears to be one of the most important. I think you and the membership as a whole are, and have been, well aware of this. The annual tour of the President .and Secretary, particularly their visits to Branches, shows this to be true. The interchange of ideas through the medium of the BULLETIN also illustrates the point; indeed, most Institute activities are directed along these lines. I am convinced that much more could be accomplished if it became financially possible to do so. Many able and fine men are, I think, willing and anxious to give their time and energy to furthering these phases of Institute activity, but it is unfair to expect them to assume as well the financial obligations involved. Specifically, I would suggest that the following could be done if sufficient funds were available:

Jan 1, 1952

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

By Andrea Lisjak Bradley

Clay shales are currently being assessed as possible host rock formations for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this thesis was to develop and validate a mechanically-based model of the deformation and failure process of a clay shale, namely Opalinus Clay (OPA), with particular focus on the influence of anisotropy on the short-term response of circular tunnels. To achieve this goal, a hybrid continuum-discontinuum numerical approach was developed in combination with new field measurements from the Mont Terri underground research laboratory. The response of OPA during the excavation of a full-scale emplacement (FE) test tunnel was characterized by geodetic monitoring of wall displacements, radial extensometers and longitudinal inclinometers. The deformation measurements indicated strong directionality induced by the combined effect of in-situ stress field and bedding planes striking parallel to the tunnel axis, with the most severe deformation occurring in the direction approximately perpendicular to the material layering. Computer simulations were conducted using a newly-extended combined finite-discrete element method (FEM/DEM), a numerical technique which allows the explicit simulation of brittle fracturing and associated seismicity. The numerical experimentation firstly focused on the laboratory-scale analysis of failure processes (e.g., acoustic activity) in brittle rocks, and on the role of strength and modulus anisotropy in the failure behaviour of OPA in tension and compression. The fracturing behaviour of unsupported circular excavations in laminated rock masses was then analyzed under different in-situ stress conditions. Lastly, the proposed modelling methodology was applied to the aforementioned FE tunnel to obtain unique insights into the EDZ formation process around emplacement tunnels for nuclear waste. The calibrated numerical model suggested delamination along bedding planes and subsequent extensional fracturing as key mechanisms of the damage process potentially leading to buckling and spalling phenomena. Overall, the research findings are already having a direct impact on the preliminary design process of an underground repository for nuclear waste in Switzerland.

Jan 1, 2015