Search Documents

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By Marc Lavigne

"The Lac Knife graphite deposit was estimated, as part of a feasibility study, using a geostatistical ore reserve estimation method: ordinary kriging. Based on the geology and its interpretation, the results of a variogram study, and the statistical parameters of the grade distribution of the core samples and the composites through the mineralization, the deposit was divided into three separate zones (west, centre and east), and each of these zones was then analyzed and kriged independently.The geological ore reserve estimation results of ordinary kriging are compared to the results of a conventional method (sections) used previously. The two methods gave almost similar reserve figures. The conventional method provided a +2% estimation for tonnage and + 10% for grade because it ignored the spatial relation between sections and samples, and ordinary kriging gave a more accurate longitudinal definition of the deposit.Finally, the paper concludes with the advantages of proceeding with ordinary kriging, namely: higher flexibility (change of cut-off grade), better deposit resolution and enhanced selectivity for the design of the open pit.IntroductionWithin the context of a complete feasibility study for the Société d' Exploration Minière Mazarin Inc., specialists of the Mines and Geology Division of Roche Ltd., Consulting Group, defined a modelling method appropriate to the graphite deposit of the Lac Knife property near Fennont. Many patterns were considered. Based on the geology of this deposit, the planned mining method, the statistical parameters of grade distribution and the variogram study, the process of reserve estimation retained was to use the ordinary kriging in a selective way. It was required because the geometry of the deposit is such that it was unthinkable to apply ordinary kriging without restrictions.This paper gives a detailed explanation of the observations and interrogations which led to the choice of this ore reserve estimation method, and the calculation procedure itself."

Jan 1, 1991

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By G. R. Baiden

"An Automatic Haulage Truck (AHT) has been developed for manless tramming of run-of-mine material in an operating mine. The AHT has a 70-ton capacity and uses an electric trolley system in combination with a computer control system to operate the vehicle. The purpose of the AHT was to provide a high capacity, high productivity material transfer system where conveyor belt applications are not immediately practical.The AHT project was started in 1983 at Inco Limited, Ontario Division as a result of the need for rapid material transport to match increased extraction rates resulting from bulk mining methods. The original concept was to use a continuous loader with the truck. However, in order to minimize development problems the truck project was considered a stand-alone project.The AHT project consisted of concept development, preliminaryand detailed design, manufacture, surf ace testing and mine implementation.The AHT was manufactured and ready for testing in 1988. At this point the truck was first moved onto the test track for debugging. This proved successful and in 1989the decision was made to install the AHT at Little Stobie mine on 2000 level. Commissioning of the system was started in 1990and at present a fully functional automated haulage system is in place at Little Stobie mine producing 3000 tons/day.This paper describes the project presenting results achieved to date."

Jan 1, 1992

By Gilles Carrière

"The Suffield mine is situated five miles southwest of the city of Sherbrooke, in the Eastern Townships of Quebec. lt is the property of Suffield Metals Corporation Limited, a wholly owned subsidiary of Ascot Metals Corporation Limited.The old Suffield or Griffith mine had been worked intermittently from 1863 to 1906, without ever producing much ore. In 1951, diamond drilling done by Ascot Metals proved over one million tons of ore in three new bodies. The average grade of this ore was 0·018 ounces of gold per ton, 2-40 ounces of silver, l ·28 per cent copper, 0·59 per cent lead, and 6-45 per cent zinc. Since then the mine has been active, producing between 300 and 700 tons daily. More recent exploration has found continuations of the ore zones.General GeologyThe ore of the Suffield mine is found in porphyritic rhyolites of the Sherbrooke group (Silurian), at or close to its contact with sediments of the Beauceville group (Ordovician). The contact shows pronounced folds as well as irregularities due to erosion of the sediments prior to the outpour-ing of the lavas. On surface the general strike is north, and the dip is steeply east.The footwall sediments consist of interbedded black graphitic slates and. dark-coloured chloritic quartzite, overlain in many places by a thin bed of magnetite-hearing quartzite.The rhyolite host rock is a light grey rock, containing very abundant quartz and feldspar phenocrysts in a microcrystalline matrix of the same minerals. Some sericite is always present, especially in the vicinity of the ore zones, where the rock shows a pronounced schistosity.Several narrow basic dykes, with an easterly strike and vertical dip, cut all other formations. Most are lamprophyres, of either the monchiquite or camptonite type, but one has been identified as a diabase."

Jan 1, 1949

By George M. Douglas

The southeastern shores of Great Slave lake present a curious anomaly in geographical and geological exploration, in that an area so large and important, and withal so comparatively accessible, should nevertheless have remained unexplored, unmapped, and indeed almost unknown, until quite recent" times On their return from the famous journey to the mouth of the Coppermine, the band of Indians with whom he travelled led Samuel Hearne across Slave lake. He was the first white man to see that great body of water and it is rather curious that it should have been seen first from the north rather than from the south. Hearne's account of the lake is vague, and he made no attempt ?to map the part through which he travelled. About 30 years later John Franklin, on his first journey to the Arctic, crossed the lake from the mouth of the Slave river to the Yellow Knife river. Franklin's maps show all of his route in accurate detail, except that part of it which lay through Slave lake. In 1833-34, Captain, afterwards Sir George, Back made the first exploration of the eastern end of the lake. Captain Back was then on his way to the Arctic coast by way of the Great Fish river, and his Indian guides led him through Great Slave lake by the route they had followed from time immemorial. This route, partly because of its directness, and partly because of its sheltered character, lay through the great mass of islands in the middle of the lake to the Talthei narrows, and thence along the sheltered north shore with its many coves and harbours. Pere Petitot made extensive journeys in Slave lake as well as other parts of the far north.

Jan 1, 1929

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By F. Nava-Alonso, A. Uribe-Salas, C. Rodriguez-Rodriguez

Ozone has been proposed to pretreat refractory ores before the cyanidation process for precious metals extraction. As pyrargyrite is one of the silver species most common in Mexican refractory ores, the ozonization of this silver sulfide was studied. The effect of pH and ozone concentration on silver dissolution was evaluated by means of a factorial experimental design. Two levels of sulfuric acid concentration and ozone in gas concentration were evaluated: 0.18 and 0.72 mol/L of acid and 0.054 and 0.077 gO3/L, respectively. The highest silver dissolution was obtained when using the higher acid and ozone concentration.

Jan 1, 2011

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By Garth A. Maki, Douglas M. Smith

"The largest Canadian Lamella thickener installation to date, with 13,600 square feet of effective clarification area, is being successfully operated at the Rocanville Division of the Potash Corporation of Saskatchewan. This paper describes the operational principles and design features of the Lamella thickener, the testwork leading to its specification f or the Rocanville phase two expansion project and a review of the performance of the full- size unit which was ultimately installed.IntroductionThickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated an d he a ted structure due to the harsh winter climate and the need to closely control plant brine temperatures to en sure good flotation circuit performance Because these thickeners process large volumes of slurries, conventional basin-type designs tend to be large, ranging up to 46 metres in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a LamellaTM thickener and one other type of ‘High Rate' thickener as alternatives to a conventional design for the phase two expansion project.This paper describes the operational principles and design features o f the Lamella thickener (manufactured by Axel Johnson lnc.), the testwork leading to the specification of a Lamella for the Rocanville expansion project and are view of the performance of the full size unit (1486 m2 of the effective settling area) which was ultimately installed and is now successfully operating in the Rocanville plant."

Jan 1, 1983