Search Documents

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By H. Thomasson

THE war, like all destructive agencies, has focused attention on salvage and conservation, and to such an extent that a decade of normal progress has been crowded into a few months. This is particularly true as regards the repair of cutting tools. As a consequence, there has arisen a wide demand for comparable data by those engaged in such work, and for basic information by others who wish to repair tools. These repairs may be grouped in three classes: (1) The repair of broken tools of relatively slender cross-section, such as broaches, reamers, drills, etc., of a type that could be returned to service if a means to join the broken surfaces were available, as fortunately it is in the low-temperature silver solder process; (2) the repair of tools that possess shanks, tangs, and other non-cutting portions that may be broken or damaged to the extent that only the addition of metal will permit their return to service; and (3) the repair of special rotating tools, such as end-mills and milling cutters, that may have portions broken from the cutting edges or have their edges so worn in service as to require building up.

Jan 1, 1943

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By Melvin S. Taylor

The environmental control program at Cassiar Mine is an active one involving government, unions and company personnel all working together to achieve a goal- "A clean and safe working environment". This can only be achieved by utilizing three of Cassiar's most important resources; i.e., people, time and money. Past environmental programs have more than proved that the goal can be reached and. with the future programs now in progress. Cassiar Asbestos will achieve its environmental goals.

Jan 1, 1978

By S. Khoshkhooei

In this research, the effects of rare earth elements addition on thermal fatigue behaviors of AZ91 alloy were studied. Repeated heating and cooling cycles were applied on the samples at 170°C and 210 °C to develop thermal fatigue cracks, Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy (SEM) as well as energy dispersive X-ray spectroscopy (EDS), Thermal fatigue behaviors were improved successively by addition of up to 2-wt% RE, This improvement is attributed to consummation of the aluminum of the melt by precipitation of the needle shape Al 11 RE3 phases, This process reduces the volume of Mg17Al12 phases and consequently decreases the brittle Mg/Mg17Al12 interfaces which are the main reason of weak thermal properties of the alloy at rather high temperatures, Further additions of RE, however, reduced the thermal shock resistance of samples by increasing in the mean length of the brittle needle shape phases.

Jan 1, 2005

By John Knox

The object of this paper is to present an analysis of the major problems encountered both in the design and application of downhole drills. Particular reference is made to design features governed by: physical size limitations; metallurgical material standards; physical operating environment; range of commercial materials to be drilled; high power output required, coupled with simplicity from the operating and maintenance viewpoint; and bit design. The history of attempts to develop downhole drills is discussed, and representative mechanical configurations are illustrated. The general design and application aspects of the different types are commented on. The application of this drill type in various commercial fields, such as (a) oil-well drilling, (b) open-pit mining and (c) underground mining, is discussed, along with the limitations presently imposed by the commercial state of the art in the manufacture of accessory equipment; e.g., drill rods, air compressors, mountings, etc. Suggestions on the possible future direction of the development and application of this tool are put forth.

Jan 1, 1965

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By R. J. Fruehan

Oxygen steelmaking (OSM) is not only the dominant steelmaking process but defines the structure of the industry. There are a number of myths regarding the future of OSM, which are false. These myths include that the EAF will become the dominant process in the near future, it is less costly to produce steel in an EAF and OSM is a mature technology and no new developments are occurring. These myths are shown to be false. Selected new developments are discussed such as post combustion, recycling of waste oxides, slag splashing and sensors.

Jan 1, 2004

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By M. Remillard, M. Garon, M. Thérien, D. Hodouin

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami division of Noranda Inc. have been sampled for particle size distributions chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMAT. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper clean¬ing flotation stages and to determine how overall silver and three silver-bearing minerals are recovered in the plant final products.RESUME Dix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, analyses chimiques et le contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMAT. Ces résultats couples avec une etude minéralogique à la microsonde sont utilises pour quantifier les pertes argentifères aux diverses étapes de nettoyage du circuit de cuivre et pour de¬terminer la repartition de l'argent et des trois minéraux argentifères dans les produitsfinals de l'usine.INTRODUCTION The Matagami division of NORANDA INC. produces copper and zinc concentrates from a sulphide ore which contains a small amount of gold (0.34 g/t) and silver (20 g/t). Only a small part of the silver (~-30%) is presently recovered in the copper concentrate. The objective of this study is to evaluate the metallurgical behaviour of silver, and secondarily of gold, in the flotation circuit for a possible increase of its recovery in the copper concentrate to improve its economic value. For that purpose it is worthwhile to study the minerals which bear silver and to determine the critical flotation stages where they are lost in the tails. The methodology proposed here is based on a coupling of a mineralogical study and a detailed mass balance calculation in the flotation circuit."

Jan 1, 1986

By H. A. Steane

THIS PAPER describes the re-grind section in the 2,000-ton per day, lead-zinc flotation mill of Canadian Exploration Limited, near Salmo, B.C. There are two re-grind units in operation, one in the lead circuit, and one in the zinc circuit. In each unit, the rougher concentrate is re-ground ahead of the cleaning circuit. These re-grind units have made valuable improvements in the concentrate grade, and with no loss in recovery by over-grinding galena or sphalerite. Since the initial installation of this re-grind section, the plant throughput has been increased gradually from 1,600 tons to 2,000 tons per twenty-four hours, and, as shown by the screen analysis of mill tailing, a coarser overall grind has been accepted, from 55 per cent to 45 per ?cent minus 200 mesh. There has been no increase in grinding capacity, but two mills have been taken from the main grinding circuit and used for the re-grind circuit.

Jan 1, 1958

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern 'British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company's share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company's working capital is approximately $1,500,000.

Jan 1, 1963

By S. Sillitoe

In mining, as in other business and engineering enterprises, efficient operation depends upon how well and how quickly the lines of communication can function. Mines have used the telephone on and between levels for many years, but in the hoisting shaft maintenance of physical wire connections for communication with the moving cage or skip has been found, for all practical purposes, impossible. A most natural solution was, therefore, the code-bell or buzzer signal system between fixed levels, and this has been standard practice throughout the mining world for many years. However, this system has serious limitations which make it impossible to signal a cage between levels in the shaft, and it requires crude, hazardous or costly methods for signalling during daily shaft inspection. Radio signalling overcomes these difficulties, because the communication medium is never broken and the cage-tender or shaft inspector can safely signal to, and receive signals from, the hoistman at any time from any position in the shaft, whether stationary or in motion. In addition to both audible and visual code signalling, two-way telephone communication and slack cable alarm are facilities made possible in recent commercially developed equipment.

Jan 1, 1949

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986