Search Documents

By A. P. Fletcher, K. Croteau

The intent of this paper is to cover some aspects of preventive maintenance methods which have come into wider usage in recent years as a means of increasing operating efficiencies. Particular emphasis is placed on lubrication and related servicing.

Jan 1, 1967

By Pingchao Ke, Zhihong Liu

Fe(III)-As(V) precipitates were synthesized from the Fe(II)-As(V)-SO42--H2O system at 90°C in initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The synthesis were carried out by introducing oxygen gas into the system to oxidize Fe(II) ions into Fe (III) ions, and at the same time, adding aqueous sodium carbonate solution into the system to neutralize the acid released by the hydrolysis reactions, with the purpose of keeping the pH constant at 1.5±0.05. The precipitates obtained were characterized by XRD, chemical composition analysis, SEM, XPS, and Raman spectrum. The results indicated that the particles in the precipitates were in the morphology of irregular aggregation with their sizes in the range of about 1–4 µm. The precipitates consisted of scorodite, ferric arsenate and amorphous hydrated ferric oxide, of which amorphous hydrated ferric oxide formulated as Fe(OH)x(SO42-)y. The characteristic XPS peaks of Fe-AsO43- and Fe-O in the precipitates located at 711.8 and 713.3 eV, separately, and the existence of amorphous hydrated ferric oxide led to two series of shake off lines developed over the end of high binding energy of Fe2p XPS. The precipitates were stable in TCLP tests at pH 4.93 for 60 hours with the arsenic concentrations in the leaching solutions being 0.27 mg/L and 0.59 mg/L for the precipitates prepared in the initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The tests for the long-term stability of the precipitates were carried out by leaching them for 40 days at 25°C under various media in the pH range from 9.50 to 10.57, and the results showed that the precipitates synthesized in this study were much more stable than those by previous researchers.

Jan 1, 2017

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By Ben Sheneider

AT THE Flin Flon plant of the Hudson Bay Mining and Smelting Co., Limited there are two types of multiple hearth furnaces used in the roasting of sulphides. This pa-per will deal primarily with the wedge-type furnace in the roasting of zinc concentrates. The other furnace, the Nichols-Herroshoff type, is used in the copper smelter and is described in the papers given by (1) J. H. Ambrose in 1935 and (2) R. E. Mast and G. H. Kent in 1954. The design and operation of these roasting furnaces at the present time is essentially the same as given in the write-up in 1954. No at-tempt will be made here to describe these furnaces, except to mention that there are five Nichols-Herreshoff multiple-hearth furnaces, four of which are used to roast a dried mixture of copper concentrate, zinc plant residue, and flux, before this material is fed to the reverberatory furnace.

Jan 1, 1961

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By J A. Gilliand

Mineralogical cross sections of orebodies on the 300-,600- and 900-foot levels of the Coronation mine have been interpreted in terms of centers of mineralization. The maximum concentration of chalcopyrite occurs closest to these centers, with pyrite and pyrrhotite concentrated some distance away. The magnetite concentrations are farthest removed from the centers. A hydrous halide fluid model is established. Attempts to explain the observed mineralogy by the action of temperature gradients on the fluid model were unsuccessful. Likewise, the action of diffusion alone on the fluid model cannot explain the observed mineral distribution. The concept of attenuation is introduced-i.e., the rate of diffusion of a particle species is related to the product r2 I/ M, the attenuation coefficient, where r is the particle radius and M its molecular weight. Attenuation, acting on the fluid model alone, will not produce the observed mineral distribution, but, when considered together with the action of temperature gradients, the observed mineralogy can be well explained by the combined effects of these two processes on the assumed fluid model.

Jan 1, 1965

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By D. J. M. Farnsworth

Since the 1.940's, the bulk of the ore production from the Sullivan Mine has come from pillars. These pillars, located from 100 to 2000 feet below surface, have been subjected to considerable ground pressure. Mining techniques were adopted to minimize the problems of deteriorating ground conditions. These techniques included an orderly sequential blasting of pillars along a retreat front, stage blasting of tall pillars in horizontal slices and utilization of broken pillars as "buffers". The latter two techniques involved leaving substantial tonnages of broken ore in place for as long as 4 years. Rapid oxidation of metal sulphides, with attendant heat and noxious gas generation, had occurred in a few very localized areas of the mine associated with a major water course. However, in a very short period starting in 1972, sulphide fires spread to several of the large blocks of broken ore that had been left inactive for lengthy periods. There proved to be no feasible method of extinguishing these fires, except by complete removal of the burning ore. The attendant problems of handling large tonnages of burning ore have had considerable negative impact on the mine operation. The chemical reactions involved in these sulphide fires have been studied by the mine staff to determine the conditions necessary for' initiation and propagation of the tires. Techniques to safely and efficiently handle hot ore have been implemented and refined. Lastly, and most important, mining methods at the Sullivan Mine have been revised to ensure that additional fires do not occur.

Jan 1, 1977

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By Tom Shumka

INTRODUCTION ?The Electro-Magnetic Crack Detection (EMCD) technique is an electromagnetic inspection method used for detecting and sizing surface breaking flaws. ?It works well on structural material or welds, ferrous or non-ferrous metals. ?EMCD?s rapid scanning is achieved using a hand-held probe. ?EMCD provides reliable crack detection and sizing (length and depth). Cracks can be sized accurately. ?EMCD dramatically reduces most cleaning requirements as there is no need to clean to bare metal. ?EMCD is capable of inspection through thin metallic coatings, or through non-conducting coatings up to 10mm thick. ?EMCD allows full data storage for back-up, off-line view and audit purposes.

Oct 1, 2010

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By R. C. Becker

Welding is playing an important role in the manufacture of construction equipment as used in the mining industry. It provides design possibilities which are unique to this method of manufacture, and normally makes possible lighter weight but stronger products, which can be a definite advantage to a user. Welding is an industry that has experienced major developments over the past decade, all of which have improved our capability to make better welds and make them more economically. International Harvester Company has been introducing these newer welding methods into its manufacturing plants, particularly those producing construction equipment, just as fast as their value has been proven. This paper discusses how modern welding methods are contributing to the manufacture of strip mining equipment.

Jan 1, 1966