Search Documents

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By P. A. Studemeister

"A trondhjemite stock intrudes a volcanic sequence that has massive sulphide lenses and that is metamorphosed to the greenschist facies at Gutcher Lake, 25 km north of Wawa, Ontario. The stock is 4 km2 in plan and is partly enveloped by an aureole of chlorite-epidote-amphibolehornfels up to 1 km wide. Within this contact aureole, biotite is partly pseudomorphosed by chlorite;epidote and hornblende are mottled by chlorite, calcite, plus quartz; albite has 0% An to 8% An; and hornblende porphyroblasts have actinolite rims. The stock has chlorite pseudomorphous after biotite; and feldspar is mottled by white mica plus calcite and has a clear rim of albite. Fractures filled with quartz, calcite, ankerite, chlorite, white mica, pyrite, and native gold cross-cut the stock and its hornfels aureole. These gold-bearing veins are enveloped by foliated rocks with quartz, calcite, white mica, and chlorite that grade outward from the veins into trondhjemite or hornfels.The stock, emplaced into a submarine volcanic series, emanated heat that caused seawater to convect and formed a contact aureole of hornblende hornfels. The stock eventually intruded its aureole and this culminated with regional metamorphism to the greenschist facies. Regional metamorphism hydrated the stock and its hornfels aureole. Native gold precipitated with quartz along fractures from metamorphic flu ids in response to cooling and wallrock hydration. exploration for this type of gold deposits should focus around felsic intrusions that have albite and that have contact aureoles retrograded by regional metamorphism."

Jan 1, 1985

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan'!' used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By J. A. Russell

MR. M. W. Boom: I would like to congratulate Mr. Russell on his fine paper. One very good point which has always appealed to me is the smooth working of a steam hoist as compared with electrical. He does not mention the steam hoist at Springhill which has been working there for a good many years. MR. S. R. NEWTON: I have read with a great deal of interest the paper presented by Mr. Russell on the development of haulage engines in the mines of the Dominion Steel & Coal Corporation. He is to be congratulated on having produced a comprehensive article showing, step by step, the various improvements that have been made over the years in the design of such engines. I am quite in accord with Mr. Russell's statement that the positive tooth clutch can have too many teeth, and also that the method of driving a sliding clutch hub of any design should be by means of a hexagon or octagon on the shaft. Where the clutch hub does not of necessity slide on the shaft it can be pressed on and keyed to the shaft in the normal manner. With regard to the 'Cramp' internal-expanding jaw-type clutch, while it is true there are more moving parts than with the clutch consisting of a ring with internal cut teeth and a driver having a fewer number of teeth as .described by Mr. Russell; there are compensating advantages to the internal expanding jaw-type of clutch. The V shaped profile of the teeth permits of engagement of the clutch with very much less 'jockeying' of the drum. This is particularly the case in vertical-lift mine hoists, where it may be necessary to engage and disengage the clutching mechanism at frequent intervals.

Jan 1, 1944

By G. Gabra

"A process of leaching niobium oxide from pyrochlore concentrate using hydrofluoric acid is described. Variables such as acid concentration, temperature, reaction time, solid/acid ratio, agitation speed and particle size are correlated to the recovery of niobium oxide.The relatively low activation energy (1,86 Kcal/mole) and the dependence of reaction rate on agitation suggest that the process is diffusion controlled. The optimum conditions for extracting niobium oxide from the leach solution, using either methyl isobutyl ketone or tributyl phosphate have been determined.IntroductionMost of the commercial production of niobium and tantalum has been derived from the treatment of columbite - tantalite minerals.In recent years (1960) , pyrochlore mineral has been found to be an alternate source of niobium . This mineral varies widely in composition and contains in addition to the main elements of calcium , sodium and niobium, some tantalum, fluorine, rare earth elements, titanium, alkali an d alkaline earth elements.It is well known that the province of Quebec possesses several pyrochlore niobium deposits totalling approximately 151 million ton s at an average 0.45% niobium oxide(1). One of the deposits, the St-Honor carbonatite, was brought into production by Niobec Inc. in 1976. Flotation o f this material produces a concentrate of about 60% Nb205(2).In view of an expanding niobium market in recent years and the presence of large niobium deposits in the province, a research and development program was initiated at the Centre de Recherches Miner ales to evaluate known processes for the separation of niobium and tantalum from each other as well as their purification . Some work has also been undertaken at the CRM to develop an improved extraction process. T his work will be the subject of further communication s."

Jan 1, 1985

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Frank Mucciardi, Louca Gourtsoyannis

"Low and inconsistent recoveries of aluminum in the production of aluminum-killed steels triggered an extensive research program on the aluminum dissolution kinetics at McGill University. This research program led to the understanding of the melting kinetics and the hydrodynamics of making additions to liquid steel. It showed the necessity of gradually releasing liquid aluminum at the bottom of the ladle to increase aluminum recoveries.This knowledge was verified in practice at Sidbec-Dosco, where a prototype aluminum wire injector was developed and installed for the first time in Canada. The industrial application showed the validity of the theoretical and experimental results and provided further data for the mathematical modelling of the process.The development of the theoretical understanding, the industrial results, and the interaction between university and industry are presented.IntroductionAluminum is an extremely effective deoxidizer of molten steel; nevertheless, an efficient method of adding it to steel has eluded steelmakers for many years. It is well known that the recovery of aluminum used in the production of aluminum killed steel is both low and eratic, especially when the aluminum is added in the form of bars or lumps from chutes into filling ladles, a practice still common in many of today's steelmaking operations.As the density of aluminum is only about 40010 that of molten steel, it is conceivable that loose bars of aluminum simply ""thrown"" into a filling ladle will resurface before any appreciable dissolution of the aluminum has occurred, particularly if the depth of penetration of the additions is small. Before one can conclude that this is indeed the case, it is necessary to know the melting kinetics of an aluminum addition. Back in 1972, this information was not available; hence an extensive research program which focused on melting kinetics was initiated at McGill University."

Jan 1, 1982

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By J. E. Armstrong

THE Pinchi Lake mercury belt is in central British Columbia, about fifty miles north of the Prince Rupert branch of the Canadian National railway (Figure 1). Until 1936 little was known about the geology of this area. Jn 19~6 and 1937, J. G. Gray and the writer mapped the Fort Fraser area (G.S.C. maps 630A and 631A) for the Geological Survey of Canada. During the field season of 1937, cinnabar was discovered by J. G. Gray in the Permian limestones on the north shore of Pinchi lake on what have since proved to be the main showings of the Pinchi Lake mercury mine. Claims were staked in the spring of 1938 and later that year were optioned to the Consolidated Mining and Smelting Company. Development work revealed cinnabar deposits of commercial size and grade, and a small reduction plant was erected, production of mercury commencing in June, 1940. Since 1940, this plant has been enlarged by additional units. The ore treated is reported to contain between 0.5 and 0.75 per cent mercury. The production of mercury from this deposit is now far in excess of Canadian requirements and this country is able to supply the United Kingdom with part of its needs. In 1940 and 1941, several other occurrences of cinnabar were found northwest of Pinchi lake. During 1941, the writer made a geological investigation of the known cinnabar occurrences and of the belt of country in which they are located. The present paper summarizes the results of this work. The writer is indebted to officials of the Consolidated Mining and Smelting Company, and to Mr. E. Bronlund of the Pinchi Lake mine in particular, for their generous co-operation in the work.

Jan 1, 1942

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965