Search Documents

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Eirik Sundvor, Hany Doss, Peter Vogt, Kathleen Crane

"Abstract - In 1989-1990, the SeaMARC II side-looking sonar (11 to 12 kHz) and swath bathymetric system imaged more than 80 000 km2 of the seafloor in the Norwegian-Greenland Sea and southern Arctic Ocean. One of our main goals was to investigate the highly oblique (115°) junction between the Mohns and Knipovich ridges, and to determine, using new morphotectonic data, whether or not this junction is stable or in a state of readjustment. These findings are presented in this paper.Along the northern Mohns Ridge, we observed a highly segmented rift valley undisturbed by transform faults. In contrast to the elevated Reykjanes Ridge, the Mohns Ridge is dominated by deep en echelon fault-bounded troughs, which are bordered by high rift valley volcanoes. These segment boundaries are interpreted to be sites of recent to present volcanic activity, based on their high acoustic reflectivity. The northwestern flank of the Mohns Ridge is marked by shallow quasi-linear ridges parallel to the present orientation of the Mohns Ridge. The orientation and geographic position of these ridges suggest that they were formed at the Mohns Ridge. Only in the northernmost cases are some of these off-axial ridges non-linear. The degree of the non-linearities increases slightly with proximity to the Mohns-Knipovich bend. In addition, because no transform fault was detected between the Mohns and Knipovich ridges, we conclude that the Knipovich Ridge must be obliquely spreading to the NW-SE."

Jan 1, 1999

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By A. Kowalski

Telvis Limited, manufacturer of an emergency communication dispatcher's broadcasting system, now introduces the possibility of a remote software upgrade to its devices. The paper presents methods, features and ways to accomplish this task. It describes the mechanisms used and the opportunities that arise from the use of this type of functionality. The mechanism software update presented applies to devices on the surface and in underground areas of mines. The electronics used currently allow the use of remote software updates, but the mining equipment makes little use of these methods. This paper aims to start the discussion on this topic and tries to lay the path of development by showing one of the first examples of the application.

Aug 1, 2013

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945

By A. M. Ramadan

The composition of phosphate rocks, mainly used in manufacturing fertilizers, varies among deposits; therefore, phosphate rocks from different sources are expected to behave differently in acidulation processes. This paper examines the effect of preconcentration of phosphate ore from El-Sebaiya East, Egypt, using flotation on uranium leaching. A high-grade ore sample (27.3% P2O5, 168 mg/kg U) supplied by the Al-Nasr Mining Company, was subjected to reverse single-stage flotation to separate carbonate from the phosphate sample. Subsequently, P2O5 and U concentrations were 32.2% (92.1% recovery) and 225 mg/kg, respectively. After the leach process, the U concentration in the liquor was 319 mg/L.

Jan 1, 2014

By E. G. Joe

The continuing increase in costs for power and fuel are affecting significantly the cost of milling Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors, carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that, in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc .ore mills were moderate in energy consumption, and uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. Although plant heating costs varied somewhat with location, it was apparent that the lowest heating costs were achieved by those plants built with proper insulation and energy conservation design. If the cost per million British thermal units is taken as $2.00, the mill energy costs generally ranged from 40ft to $1.20 per ton.

Jan 1, 1979

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952