Search Documents

By W. H. MacLean, P. J. MacGeehan, A. J. Bonenfant

"The Norita deposit is an Archean volcanogenic-exhalative Fe-Zn- Cu sulphide accumulation of the distal type, consisting of six overlapping stratiform massive sulphide lenses, interbedded with exhalative cherts and thin pillow basalt flows, which formed down-topographic-slope from a mineralized hydrothermal discharge zone in the Norita rhyolite. The sulphide lenses are of two main types: channel-fill deposits such as the Main Zone and Main Zone West, composed of intricately layered pyrite-sphalerite-chert, which formed by the dynamic down-slope transport and re-deposition of sulphide exhaled from the vent zone; and stratiform lenses such as the Cu-rich A-Zone and A-Zone West, which formed even farther down-slope, in basinal depressions flanking the dome. Although rotated into a vertical position by folding, the sulphide lenses are otherwise essentially undeformed and contain a wide range of preserved primary sedimentary structures.Of prime importance in exploration has been the recognition that the formation of the distal sulphide lenses was controlled by submarine paleotopography, and that it is possible to approximate the sea-floor paleotopography using variations in the thickness and strike extent of the interbedded volcanic rocks. This has proved to be a major and successful exploration tool in the search for further sulphide mineralization in the mine, and offers prospects for use elsewhere in the district."

Jan 1, 1981

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By A. S. Eve

The detection of magnetic dykes by using magnetic variometers is the oldest application of. geophysics to mining, and is also one of the more simple and certain methods 0f locating such deposits. As a result of recent improvements in the instruments, it is now possible to find the dyke, deter-mine with magnetic variometers its strike and dip', with fair accuracy, and to estimate the approximate depth of overburden when there is no outcrop. The application of electrical methods may be used to distinguish mineral from diabase dykes. The authors have had an opportunity of making surveys with the modern Askania types of vertical and horizontal variometers over magnetic dykes in the Sudbury region. The interpretation of the results has been confirmed by diamond drilling in some cases, and by experiments over models. The variometers used were the standard form of Askania instruments (1). The sensitivity of the horizontal type was 17.2 gammas per division, and that of the vertical variometer double this quantity. To make a preliminary survey of the district, parallel lines were laid off two hundred feet apart running north and south, and readings were taken with the vertical variometer every 100 feet along these lines. This can be done very rapidly, and when an indication of a magnetic deposit is found, the readings may be taken every hundred feet, or less if the size of the deposit warrants smaller intervals. If the deposit is a vein or dyke, the readings along the adjacent lines immediately indicate the strike of the body. Thus the presence and strike of a magnetic dyke, whether of mineral value like the pyrrhotite and nickel deposits of the Sudbury district, or simply a worth-less diabase dyke, is simply and rapidly found.

Jan 1, 1932

By F. P. Agterberg

"IntroductionTHE KNOWLEDGE about the mineral resources in a region ranges from relatively precise ore-reserve estimates for known deposits to probabilistic estimates concerning the speculative resources which may be discovered in future at greater depths and in the less-explored parts of the region. Previously developed probabilistic methods for regional resource evaluation (1) are based on the following two assumptions.(1) The probability that a specific block of rock, or part of a region close to the topographic surface, contains undiscovered deposits can be estimate d by weighting selected geological, geophysical or geochemical parameters for that block. The weights are computed by considering similar environments which are known to contain deposits.(2) Some of the characteristics of the undiscovered deposits, such as ore tonnages and average grades of metals contained in the ore, can be evaluated by considering probability distributions f or known deposit data. These methods were initially applied to Precambrian deposits in the Abitibi Volcanic Belt of the Canadian Shield (1).Since 1972, statistical methods for quantitative resource evaluation have been applied to the occurrences of the mainly Paleozoic base metal deposits in t he Canadian Appalachian Region. The objectives of this project (Project Appalachia) have been discussed by Leech (2) in a paper that introduces 8 papers with results of the exploratory data analysis. Project Appalachia represents an effort to develop and apply methods of combining information and concepts from regional geology, metallogeny and geomathematics for computer- aided regional mineral resource evaluation."

Jan 1, 1977

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By J. Visman

The water cyclone washer has a number of advantages that makes it a desirable machine for the cleaning of fine-grained and friable materials such as 1,4 x 0" slack coals. In this paper results are presented of tests carried out on a shaly coal containing a high percentage of inter-grown materials from the Minto area, New Brunswick. The tests were con-ducted in the pilot plant of the Western Regional Laboratory in Edmonton. The test results show that the cleaning characteristics of this coal can be improved by lightly grinding the recirculating middlings fraction, which constitutes approximately 30 per cent (1.45-2.00 fraction) of the raw feed. • The cleaning of 1;4 x 0" fines by water cyclones compares favourably with other coal cleaning machines and has an added advantage of being extremely simple to operate, low in capital and operating cost, and high in capacity. The application of water cy-clones dates back approximately ten years, following its development at the Dutch State Mines. ( 3) A number of papers published d

Jan 1, 1961

By W. A. Roliff

The renewed interest of the past few years in the Appalachian and Michigan oil provinces has not, as yet, created any marked increase in activity in Southwestern Ontario. During 1960 development drilling in-creased somewhat over 1959, but exploratory drilling decreased slightly. More attention was devoted to the deeper horizons, but lake drilling de-creased considerably. Oil production reached a new peak and gas production increased slightly. During 1960 an interesting oil and gas discovery was made in the Cambrian and gas discoveries six miles off-shore in the eastern part of Lake Erie were made in the Clinton-Cataract zone of the Silurian. This paper reviews activities during 1960, summarizes the discoveries made to-date and the pertinent exploration data relating to the prospects of the region and discusses some of the economic aspects of exploration and development. D URING the last few years there has •been a marked renewal of interest in the old petroleum

Jan 1, 1961

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to 'Iron Ore in 1954', involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company's current mining practices.

Jan 1, 1958

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940's has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

By Graham E. Brown

Since the beginning of time, people later to be known as engineers and architects have strained to create methods whereby they could improve technology to assist them in their various fields of endeavour. Some of these improvements would be the change from linen paper, french chalk and ink pens to drafting film , mylar an d pencil for the production of drawings, the drafting machine in lieu of the tee and set squares, even tap e to attach drafting media to the board instead of thumb tacks and man y, man y more. All of these taken individually are insignificant but combined evolve to the current state-of-the-art in the computerized engineering environment. Ten years ago the major topic o f conversation was the hand-held calculator which for a cost of around $150 would give most trigonometric functions. Today the equivalent calculator can be purchased for around $25, is about one third the size, and if inflation were included over the last ten year s the item should cost around $550 in today' s dollars, it can be seen that tremendous advances not only in the technology but also the cost saving. The following paper is intended to outline some o f the significant aspects o f the latest technology in the computerized engineering office namely Interactive Graphics Systems.

Jan 1, 1985

By L. Larson

Rock samples were taken, away from zones of mineralization , from seven sections of five rhyolitic zones as define d by Spence (l967) in the Noranda area. The purpose of the investigation was to test whether there were intrinsic differences between the zones which would differentiate between non-productive zones and productive zones. For the elements sought (major elements, Cu , Pb , Zn and S) , no clear chemical difference between the zones was found. Thus, identification of a favour able zone from the over -all composition of the zone does not appear promising. Within sampled sections, there is no clear gradual compositional change up through the sections. A capping of highly siliceous massive rhyolite is present in five of the sections sampled. A layer of relatively basic material occurs near the base of individual units. The third (mine zone) and later zones contain abundant pyroclastic material, where as the non-productive zones do not.

Jan 1, 1977

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By Lauri Pesonen

"Although electrical energy use at copper smelters is typically about 15-20% of operational costs, it is something which is not very often analyzed and discussed at a detail level in technical papers and presentations. This paper aims to list different equipment configurations per smelter area and estimate their electrical energy consumptions versus unit of material processed. In addition chosen smelting technology and oxygen enrichment rates affect the overall electricity consumption and therefore some overall guidance is provided for efficiency gains.INTRODUCTION In principle, processing plants, such as copper smelters, require electrical and chemical energy together with some degree of human input to process input materials into desirable output form like metallic copper. From the standpoint of metallurgical plant designers, the thermodynamics of smelting, when it comes to releasing and conserving thermal energy, is sufficiently understood and frequently discussed in the literature in detail, but judging from the quantity of publications, the way how we exactly utilize electrical energy is not. This article is meant to illustrate how electrical energy consumption is distributed among different process units and equipment types at copper smelters using various smelting technologies. In general, typically about 15-20% of operational costs are related to electricity and at locations with high electricity prices the potential savings can be quite significant for the overall profitability of the plant operations. In today’s tight profit margin environment any potential savings are more than welcome. The purpose here is not to promote any certain copper smelting technology, but to open a discussion on how and where we use electrical energy, and how the overall energy use could be lowered with the implementation of newest electric power saving designs and solutions. Using the principles outlined in this article, it should be fairly easy and straightforward to replicate the calculations and even improve them wherever it is seen necessary for the greater benefit for us all in this industry"

Jan 1, 2017

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By M. F. Goudge

THE present century has witnessed an amazing transformation in the uses of limestone. From being mainly a structural material, a role it has played since the beginning of civilization, it has become one of the in-dispensable raw materials for use in the great chemical and metallurgical industries that play such a vital part in the economic life of the nations today. Its uses have become so diversified and numerous that it enters, directly or indirectly, into nearly every phase of modern life. In this introductory paper it is proposed merely to outline the general usefulness of limestone and to point out some of its salient features, and to leave any detailed discussion of uses to the papers that follow. The term limestone as herein used embraces all kinds from the variety known as high-calcium limestone, which is composed almost entirely of calcite, to the dolomitic variety, composed largely or entirely of the mineral dolomite. Lime is simply calcined limestone and, in considering the uses of limestone, the uses of lime should also be included, particularly in view of the fact that, in many processes, it is possible to use limestone in either the raw or the calcined state.

Jan 1, 1939

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By A. Deneys

This paper reviews industrial gases used in primary copper production. Copper smelting industrial gas demand has steadily increased since the first commercial oxygenconcentrate smelting in 1952 [1]. In copper production oxygen for smelting is the dominant industrial gas use followed by oxygen for converting. Nitrogen is finding increased use in copper smelters. Nitrogen is used for porous plugs for copper converting and anode refining [2-5]. Nitrogen can be used for concentrate drying [6,7] and is also used in some Ni-Cu smelters as a coolant in Peirce-Smith converting [8,9]. Industrial gas supply options of cryogenic or adsorbent based on-site plant or cryogenic liquid delivery are detailed.

Jan 1, 2007