Search Documents

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review' of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff's review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By W. D. Haley

The report of the Forestry Committee, presented to the recent Imperial Conference at London, is discouraging in its view of the future of timber resources and supplies. From a review of the forestry situation throughout the world, there is every likelihood that, thirty years from this, a shortage of the soft-woods will be severely felt. In the United States, only about one-third of the present forest area contains virgin timber. This will be cleared at the rate of five and a half million acres a year, so that in twenty-five years it will be about all gone. Canada has only about 27 per cent of her original forests left, and her virgin soft-wood will last but another half century. At the present time, the value of her lumber products is over $300,000,000 annually. During the summers of 1909 and 1910, the Government of Nova Scotia caused an examination to be made of the forest conditions in this Province. The reconnaissance, which was under the direction of Professor B. E. Fernow, of Toronto, involved an examination of the various soils, the rate of growth of the wood, and a general survey of the forest area. The importance to the Province of conserving its forest resources was clearly shown, and a number of recommendations were made, which; however, were never acted upon.

Jan 1, 1927

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

By Douglas Macaulay

"The Work contains the personal views and opinions of the Author and in no manner should it be construed as reflecting the official position of Export Development Canada. The Author makes no representation or warranty with respect to the accuracy or completeness of the contents of the Work and specifically disclaims any implied warranties, merchantability or fitness of use for a particular purpose". Export Development Canada ?Canada?s official export credit agency, established 1944 ?Mandate to support export and foreign investment ?Financially self-sustaining, AAA rated borrower ?Services include: Financing (FIN), Political Risk Insurance (PRI), Contract Insurance & Bonding (CIB), Accounts Receivable Insurance (ARI) ?A trusted partner in troubled times

May 1, 2010

By V. L. Eardley-Wilmot

Introduction We are all familiar with the bright and attractive colours of the roofs of our suburban houses and country cottages, but few of us fully appreciate the complex and highly technical nature of the business which produces these roofings. Roofing granules consist of small broken particles of certain types of rocks, burned clay products, or slag. They are used either in their natural state or artificially coloured and are affixed onto one surface of asphalt sheeting. Their main functions are to protect the roof against external fire hazard, prolong its life, and enable it to withstand extremes of weather over a period of years without deteriorating. Pleasing designs and colours are added attractions. The reverse, or inner side, of the sheeting is coated with a film of talc or fine mica to prevent it sticking when rolled up for convenience of handling for transport. The finished sheets or strips are cut into a variety of shapes for roofing shingles, or for sidings which resemble rows of bricks separated by mortar. In Canada, the consumption of roofing granules has increased fourfold in the past decade and indications are that the industry will continue to expand. At present, fourteen plants are engaged in manufacturing granule-coated roofings, but, apart from a relatively small output of natural granules by two producers in British Columbia, only one eastern producer makes both natural and coloured granules in Canada, and these only for its own use. The annual consumption is now over 77,000 tons of roofing granules valued at more than $1,600,000, but about 62 per cent of the tonnage is imported. It is thus apparent that the production of Canadian-made granules, both natural and coloured, could be considerably increased. This paper is presented in order to give an outline of the industry and at the same time to point out its difficulties and pitfalls.

Jan 1, 1946

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By J. J. Denny

IN November, 1932, an investigation of silicosis was undertaken at the Mcintyre Porcupine mine, Schumacher, Ont., after a discussion of the p"roblem with Sir Frederick Banting and his staff. As a result, it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions. At that time 50 guinea pigs were placed in the crusher house tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation (1) led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill. The CO, combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid, and alkaline solutions on the solubility of siliceous materials. Gye and Purdy (2) were the first to point out that the chemical reaction, and not the physical presence of siliceous material, was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings (3), who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response, while the 10-12 micron particles produced only a foreign-body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter.

Jan 1, 1937

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By J. O. G. Sanderson

THE Brazeau river is a relatively short foothills stream in western Alberta and its drainage area is limited to approximately 2,400 square miles. It rises near the head of the North Saskatchewan river, about two-thirds of the way from Banff to Jasper, and is confluent with the North Saskatchewan at a point about 40 miles north of Rocky Mountain House. It is not the purpose of this paper to describe the geology of all of this area. Only the central portion, which lies east of the outer limestone ranges and takes in the outer folds of the foothills belt, will be dealt with. This area is shown on Figure 1. A small portion of the area described lies in the drainage basin of Pembina river, which flows into Athabaska river. The area to be discussed may conveniently be termed the 'Brazeau area', since Brazeau is the name of the river basin referred to above, of an out-lying limestone range, and of the only large settlement or community in the region, the mining town Brazeau. One of the first Factors of the fur trading post of Rocky Mountain House in the early years of the nineteenth century was Louis Brazeau. Coal mining during the past 25 years, and more recently exploratory drilling for oil, have brought the district into some prominence. The Brazeau area was visited by D. B. Dowling for the Geological Survey of Canada in 1906 and 1907 (1). His traverses and reports dealt mainly with the Kootenay coal deposits. It is doubtful if he traversed the outer foothills area with which the present paper deals. His reports on rich coal deposits in the Bighorn Basin area attracted commercial interests, and in 1908 large tracts were leased as coal lands. James McEvoy mapped and studied the coal seams in that year, and G. S. Malloch, of the Geological Survey of Canada, made a complete survey of the whole of the Bighorn basin. His report (2), published by the Survey in 1911, describes the stratigraphical geology and names the formations. Further references to the geology of the district, mainly in relation to coal, are made by D. B. Dowling (3) and by J. S. Stewart ( 4). In the period between 1913 and 1920, the area was traversed by private interests in search of likely oil structures. A well was started in 1914 along the Saskatchewan river about 19 miles west of Rocky Mountain House, and drilling was undertaken by Imperial Oil, Limited, in 1921 at Coalspur.

Jan 1, 1939

By G. H. Robbins

"Originally presented at TORONTO 94, CIM-AGM, this paper has been updated to reflect the present status of business development for theSO2/AIR process. The paper reviews the back-ground leading to the invention, discusses the process chemistry and historically tracks the commercial development. Engineering and cost considerations are presented.IntroductionThe year 1994 was particularly significant in terms of the technical and business development of the INCO SO2/AIR cyanide destruction process. The year marked a decade of service to the world mining community since INCO acquired the Canadian patent in 1984. In that time period, the technology had become widely recognized as the state-of-the-art process in the field of cyanide detoxification and today we enjoy the distinction of having licensed the process at over 50 project sites worldwide. The application for the process has mostly been in the mining industry in precious metal recovery plants where it offers treatment for a wide range of waste streams such as: CIP/CIL slurries, Merrill-Crowe barren bleed solutions and/or re-pulped filter cakes, tailings pond water recycle or discharge, make-up water to flotation circuits and feed to underground backfill plants. The process also applies to the treatment of high cyanide rinsewaters from metal plating shops. More recently the process is being applied to the rinsing and abandonment of heap leach pads where it has proven to be a very cost-effective application of the INCO process. The distinct advantages that have led to the success of the process are the ability to work on slurries as well as solutions and the significantly low cost of sulphur dioxide products. The process is safe and easy to manage and uses all forms of SO2(liquid, gas or salts) which gives the process tremendous versatility with respect to geographic application. Having more than ten years of service"

Jan 1, 1996

By C. Kunze

ABSTRACT Although closure sureties cover works that are carried out during the existence of a mining company, certain liabilities are not known when the surety is established and become apparent only in a late stage of the closure phase, or even after the site has been relinquished. This paper supports the concept that these financial risks lend themselves to insurance solutions. Making insurance for unknown liabilities mandatory while defining unambiguous legal conditions could create a viable market for insurance products, provide a sufficient statistical basis for the calculation of premiums, and reduce costs.

Jan 1, 2013

By Abu Syed H. Kabir, Mehdi Sanjari, Steve Yue, Jing Su, In-ho Jung

AZ31 magnesium alloy sheets were produced by high speed rolling (HSR) at 1000 m/min at a low temperature of 100 ?. A high reduction of 72% can be achieved in single pass. At the reduction of 30%, the microstructure was covered by shear bands and twins. When the reduction was increased to 49%, dynamic recrystallization (DRX) was clearly observed in the vicinity of shear bands and twins and the full recrystallization was seen at a reduction of 72%. In order to study the static recrystallization (SRX) behavior on the heavily twinned structure, annealing was then carried out at 200 ? on the as-rolled specimens at the reduction of 30% for different times. Static recrystallized grains were also firstly observed on shear bands and twins after 45 s and the microstructure was mostly fully recrystallized after 1 h annealing with a few retained large elongated un-recrystallized grains. Texture weakening was found during annealing on the heavily twinned specimens by SRX, but not during high speed rolling by DRX. In the present study, effect of DRX and SRX on microstructure and texture evolutions during rolling and annealing were compared.

Jan 1, 2015

By H. H. Bleakney

The merit of reduction-in-area as a criterion of quality in metals is shown to lie in its influence on breaking stress, but the virtue of elongation is not easy to find. In order to assess the value of elongation, either as a measure of quality or as a guide to design, it will be necessary to separate the overall de-formation occurring in tension tests from the localized deformation associated with localized reduction in area. The obstacles to a successful solution of this problem have been shown to be more formidable than is generally appreciated, and a new solution to the problem has been suggested. This solution involves a de-vice by which an electric circuit is broken when the particular value of strain is reached that is to be taken as the point of separation between general and localized deformation. The report presents results from a number of tests on both low-carbon and alloy steels. These results indicate that the selected criterion of separation is accurately identified by the proposed method; that it

Jan 1, 1962

By H. A. Khorami, T. Wong, B. Velapatino, E. Asselin, T. Donnelly, E. Bryce, R. Dixon

A copper–nickel concentration gradient alloy was designed and fabricated through a powder metallurgy (PM) process. Copper and nickel powders were mixed with different weight ratios from 0 to 100% copper in 10% increments. Each powder mixture was poured inside a cylindrical die and compacted between two punches using a hydraulic press machine at pressures up to 70 MPa, resulting in approximately 1 mm thick layers (discs) of pressed Cu–Ni powder. These 11 Cu–Ni compacted powder layers, i.e. 0–100% Cu with 10% increments, were then compressed together with pressures up to 420 MPa to form a green part. The green part was sintered in a vacuum furnace at 1000°C for 10 hours to form a solid mass (PM part) of Cu–Ni concentration gradient alloy. In the sintering process, Cu and Ni particles fused together and formed a single piece due to diffusion of the atoms across the boundaries of the particles. The diffusion of atoms also converted the stepwise concentration change into a uniform concentration gradient. INTRODUCTION Copper has numerous applications in different industrial sectors due to its superior physical, electrical, mechanical and chemical properties such as its excellent thermal and electrical conductivity, resistance to fatigue, high ductility, and resistance to corrosion. Moreover, copper and its alloys have natural antimicrobial properties. This has opened up new applications for copper–based self–disinfecting surfaces in healthcare in an effort to mitigate healthcare–associated infections (HAIs). HAIs affect millions of patients each year, leading to significant morbidity and mortality as well as financial losses to healthcare systems (World Health Organization, 2016). HAIs spread through three main routes: (a) iatrogenic in which HAIs are a direct consequence of medical encounters and/or treatment; (b) person to person where organisms are transferred between healthcare workers, patients, and visitors; and (c) environmental where transmission occurs via contaminated surfaces and equipment (e.g. doorknobs, railings, toilets/commodes, medical carts). The use of antimicrobial copper–based materials on high touch surfaces could diminish pathogen transmission via this latter rout. This has subsequently led to the development of a variety of copper–based materials for use in healthcare settings and promoted the investigation of the antimicrobial efficacy of copper–based materials.

Jan 1, 2019

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By David Forrester

"At the 95th CIM Annual General Meeting in Calgary, 1993, a paper entitled “Progress on Futuristic Mining Technologies” was presented(Matthews and Sarin), in which they outlined the goal of continuous excavation of hard rock and some of the technologies being developed to achieve it. The subject continues to be featured in periodic reviews and articles in the literature, (Gertsch, 1994; E&MJ, 1995). Matthews and Sarin note the considerable success of the development and application of continuous mining technologies in the soft rock under-ground mining industry, especially those in coal and potash, with major benefit to overall production, productivity and economic viability. It is the belief that similar achievements can be realised in the underground hard rock mining which continues to drive the development of hardrock continuous mining technology.This overview has been prepared specifically for this issue of the CIM Bulletin. It attempts to tie together current advancements in continuous mining in soft rock (where remote control and automation are already well established) with the background and status of development in hard rock continuous mining. Following a brief review of key factors and machine types, soft rock aspects are discussed, then a more detailed review is given of hard rock technology, with particular reference to Canada’s HRDK Mining Research Ltd. and their key role.The mining industry has long been at the forefront of technology development, for example, the application of the early steam engine to reach reserves at greater depth for dewatering mines in the industrial revolution. By necessity, the individual characteristics of seams and orebodies dictate the mining method, continually presenting mining engineers with new challenges. One of these is the extraction process itself and the goal of replacement of the drill-blast-muck cycle by continuous excavation. Very soft rocks have always been mineable using some form of cutting, even with primative tools. However, as the challenge has been taken up, technologies have evolved to steadily increase the hardness of rock that can be mechanically excavated. It may surprise some readers that at least three machines have successfully cut and loaded rock with an unconfined compressive strength (UCS) of 250 Mpa to 300 MPa (36 000 to 43 500 psi) in field trials (Table 1)."

Jan 1, 1996

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965