Search Documents

It is a well known fact that the best method of rock reinforcement is to avoid physical ground support. This goal can be achieved by means of: - Increasing the rock structural strength - Geological definition and forecasting. - Sequencing the excavation - Smooth blasting In many cases however, extra ground support is needed in order to maintain safe working conditions. In an open pit, the structural strength of rock cannot be increased by lowering the pit walls due to economical reasons. Economy demands steeper walls and less waste to be hauled to the dump. The geological conditions can also often be extremely poor and unpredictable. For excavation sequencing and smooth blasting there are good possi- bilities, such as cleaning of the pit walls after the main excavation, arul- ing of long small diameter straight inclined holes, use of smooth blasting techniques and lightened explosives.

Jan 1, 1989

By Keast-Jones R

The relative merits of treating coal by flotation and spiral concentrators have been examined by tests on run-of-plant fines samples from three seams in the Wittingham coal measures of the Upper Hunter Valley. Flotation of the complete fines was found to be the most metallurgically efficient process with yields substantially superior to those obtained from treatment of only the deslimed fines. A strict comparison between spirals and flotation for the treatment of the deslimed fines was impossible due to differences in product quality. However, the results indicated that the performance of a flotation circuit would be equivalent, and sometimes superior, to that of a spiral circuit.

Jan 1, 1984

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

By Raczej I, Defant M

Pre-Miocene igneous rocks from the Phili pine island arc are characterised by 87Sr/86Sr and 143Nd/144Nd ratios typical for intra-oceanic island arcs where sediment involvement in the magma genesis was minor. Lead isotopic ratios are similar to Indian Ocean MORB (Mukasa et al., 1986a,b). Pliocene to recent volcanics, however, have more radiogenic Sr and Pb and less radiogenic Nd, except for the volcanics of the Bicol Arc, which have similar isotopic signatures as the Pre-Miocene rocks. We suggest that Pre-Miocene magmas and Bicol-Arc magmas have been generated in response to the subduction of the Philippine Sea Plate, their isotopic characteristics reflecting the composition of Philippine Sea crust. The Bataan arc magmas may reflect the larger amounts of sediments available for subduction in the South China Sea, while magmas of the Mindoro Arc, which are characterised by the most radiogenic Sr and least radiogenic Nd, may have been contaminated by slivers of the Mindoro-North Palawan terrane, which have been carried down to mantle depths after the collision of this terrane and the Philippine arc in Miocene (McCabe et al., 1982). This interpretation implies that Nd (and by inference other REE) can migrate from the subducted slab to the mantle wedge. Thus, variable Nd-isotopic ratios in island arc magmas (e.g. Sunda, Lesser Antillas) may not he a primary feature of the mantle wedge but a consequence of the release of Nd from the subducted slab.

Jan 1, 1987

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

By Brenchley R

Partitioning behaviour studies for -particles in the 250 to 1,000 micron size range at. the Curragh coal preparation plant are presented. Plant surveys were conducted to compare the partitioning efficiencies of dense medium cyclones and froth flotation. The aim was to assess the potential for improving yield of coal by directing more of the top size of flotation feed material to dense medium cyclones. ovel mass balancing and model fitting NI procedures were used. While flotation offers high yield of low ash particles smaller than 500 microns, dense medium cyclone rejection .of high ash particles larger than 250 microns is superior. These strengths of the two processes are turned to good advantage by the use or desliming sieve bends which tend to perform some density separation on the'size fractions of interest, directing lower ash material to froth flotation than to the dense medium cyclones.

Jan 1, 1987

By Jeffrey IC

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give back-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Leahy GJ, Wright DJ, Player RI

The operation of a one tonne submerged combustion pilot plant for the recovery of copper from anode furnace and converter slags is described and the effects of variables discussed. Using coal as reductant, copper levels of anode furnace slag were lowered to 1% or less, with batch times of approximately 120 minutes. Fluxing with limestone was required to produce a fluid slag at temperatures of 1200 - 1300¦C. For converter slags, reduction to 0.5% Cu or less was achieved in batch times of 35 minutes. The chemistry of the pyrometallurg- ical recovery of copper is briefly reviewed in relation.to copper recovery methods.

Jan 1, 1978

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990

By Eddy B. W, Washusen J. A, Wulff R. T

The State Electricity Commission of Victoria (SECV) has been con- tinuously involved in the extraction of brown coal from open cut mines in Victoria's Latrobe Valley for over 60 years, but have not completed a major mine. Detailed consideration for rehabilitation at this stage has only been able to be given to overburden disposal areas. Increasing interest in rehabilitation in the 1980's led the SECV to review its existing policies and practices and to embark in 1985 on a public consultation process to establish an agreed and accepted policy. This was extended in 1986 to the consultation process for the rehabilitation planning for the Mor- well Open Cut External Overburden Dump. This paper covers the con- sultative process developed and the lessons learned by the participants.

Jan 1, 1989

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

By Valery W, Morrell S, Loughlin P, O&apos

Traditionally, blasts in mining operations are designed to prepare the in situ rock mass for excavation and transport without much consideration being given to the downstream comminution processes. Blasting is in fact the first step in a chain

Jan 1, 1998

By McQuade CV, Riley SJ

Acid mine drainage is an unavoidable consequence of some coal mining operations. Typically runoff pH is below 3.5 and at these pH levels heavy metals are mobilised. Leachate from coal reject dumps may require collection and treatment to raise the pH and precipitate the metals before being discharged.A bi-product of coal mining operations at Clarence Colliery is coarse washery reject. At present the coarse reject is deposited above ground and rehabilitated. Adjacent to Clarence Colliery is the Kable's Transport Pty Ltd sand mining operation. It has been proposed that co-disposal of the rejects from both operations may produce a product whose leachate has near neutral pH.

Jan 1, 1998

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Unver B

Longwall advance mining is still the predaninant system of coal extraction in the U.K., contribiiting to sane 70 % of underground coal production. Gate roadways providing access to a longwall advancing coal face are maintained adjacent to a rib pillar under high strata abutment pressures and the caving rock mass. It is very difficult to realistically model such access roadways using mathematical or numerical techniques and hence, predict roadway closure. For the past 15 years, a research group in Nottingham University has been engaged in the study of longwall gate roadway stability using observation methods. Gate roadway deformations have been measured in 224 gate roadways and a comprehensive data base has been established. The paper describes the statistical analysis of this database and presents sane. predictive equations which will enable a forecast of the gate roadway closure to he made. Further field work to validate these equations. is described together with an error analysis. The results are very promising and indicate that it is possible to predict gate roadway closure in the U.K. within practical limits of Accuracy.

Jan 1, 1986

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

By Eri G

Ok ledi Mining Limited underwent a major transition from radio based truck dispatching to computerized dispatching for its equip- ment fleet in October, 1996. Modular Mining's Computerized Dispatch System was selected based on reputation and superior customer support. Modular's dispatch system is a fleet management system that uses computer, data communication and global positioning sys- tem technology to produce automatic, optimized haul truck as- signments. Optimization is achieved by equally distributing trucks to shovels so that truck queuing and shovel idling times are mini- mized. Computer illiterate mine operations personnel had to overcome a rather steep learning curve to use the high technology equipment. fortunately the system was able to be configured to use bitmap

Jan 1, 1997