Search Documents

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

By J C. Macintosh

Capcoal Mine has modified its water use practices over the past 15 years. Two issues have changed the way water was managed:an economic review of water supply options for a planned expansion of the coal handling and preparation plant (CHPP) in the early 1990s, and increasing neighbour concerns about discharge of worked water from the mine into the local streams. These issues resulted in commitment by the site General Manager to cease discharge of worked water from site and to convert from using raw water to worked water in the CHPP. Operational needs, societal demands and continuing dry weather are again demanding change to the siteÆs water management strategy. This paper outlines the drivers for past and future operational change.

Jan 1, 2006

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

It is often assumed that geotechnical investigations or studies for open pit mines are confined to providing a slope design. However in an operating mine, the design is only one component of a mine geotechnical program. Reviews of slope designs are ongoing throughout the mine life. The concept of Pit Slope Management has been formulated because the design only entails one component of a total program that contributes to a safe, efficient mining operation. Risk is a normal part of mining. Effective management allows the risk to be contained or controlled. If the slopes are not effectively managed there will be increased risk for the operation. Experience has shown that utilisation of Pit Slope Management coupled with a broad base of experience to define the key controls on stability, provides a pro-active, objective approach. The reasoning is deductive and relies on the behaviour of the ærocksÆ. Once the key aspects are defined, studies are well focused, implemented as required and the risks can be effectively managed. When the key controls on stability are poorly understood reasoning is typically more ægut feelÆ. Under such circumstances studies, if carried out, may meet short-term objectives but often ignore the long-term objectives. Hence the risk to the project is greatly increased. This paper presents several case studies highlighting the above aspects and present elements of the Pit Slope Management Program approach which have been successfully utilised by the author to manage risk in mining projects.

Jan 1, 2003

By W Pytel

A special model of vertically loaded pillar behaviour is introduced to the general, multi-plate based, floor-pillar-roof system interaction analogue. This permitted analysing room-and-pillar mine systems in any geological conditions, including the effect of pillar elastic-plastic behaviour with strain softening. In the model, pillar instability is one of the important phenomenon, which may be expected to occur, and which the operator has to be prepared for. Thus the entire systemÆs safety is determined mainly by strong roof strata behaviour and therefore they have to be examined in actual stress-strain conditions utilising the appropriate strength theories. It was assumed that the so-called safety margin, representing the relation between load intensity and material strength, might serve as the basic indicator of possible roof instability development. Therefore, the safety margin may be estimated by comparing the actually computed components of stress-strain tensor with ultimate values characteristic for a given material determined in laboratory. In order to illustrate the effect of technological pillar size on roof strata stability, two different mining systems (methods of mining) in one of the æPolkowice-SieroszowiceÆ Mine districts was modelled using the finite element method formulated in three dimensions, assuming different materials within different rock mass strata, as well as a number of horizontal planes of discontinuity within the model.

Jan 1, 2003

By Caigen Wang, Wending Ma, Xiexin Mi

The urgent need for the control of surface subsidence caused by longwall coal mining in densely populated areas of China has led to a feasibility study on the effectiveness of longwall goaf cemented backfill. The study is focussed on exploring the potential of longwall goaf cemented backfill practice for surface subsidence control. Specific backfill geometry was designed in view of the characteristics of the longwall coal mining system. Laboratory physical simulated tests were carried out with different backfill material properties and pack size. The tests achieved a marked reduction in surface subsidence by the use of goaf cemented backfill. The system has been shown to be effective in laboratory tests, the challenge now is to overcome the engineering problems to put it into practice.

Jan 1, 1998

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

The New Zealand experience has shown that the trend in technologi- cal change in gold extraction can be characterised by a systems approach which grows progressively broader with advances in understanding and allowing for an increasing number of factors. The Australian experience has demonstrated that the elements of developing an exportable process include allowing projects to prolifer- ate where substantial entrepreneural involvement is likely to occur. In both countries useful technological breakthroughs were invariably discarded when first tried at operations not well established and under great pressure of achieving and maintaining production. It required the efforts of persistent individuals at operations which had become bedded in and profitable, to follow the initial work up and commercialise it.

Jan 1, 1988

By L Soares, W T. Hennies, F Fujimura

A methodology of environmental performance evaluation in mining developments is proposed, as well as guidelines and procedures for obtaining information to improve their environmental performance. Environmental performance is the results of the mining activities and their relation to environmental issues. If this evaluation is carried out on an on-going basis, it is possible to anticipate or to identify the formation and development of an environmental impact in its early stages. Evidence or trends identified by environmental evaluation provide valuable information to prevent further damage. The proposed methodology is based on the significant environmental aspects of a selected monitored job site by environmental indicators which are then compared with previously defined environmental criteria and targets or goals. The methodology procedures also take into account the environmental accounting of the investments and expenditures.

Jan 1, 2003

By R Heath, P Rose, L Coetser

A sustained eight-year major research effort has been undertaken in South Africa to develop integrated passive water treatment systems for the sustainable removal of sulfates, while simultaneously addressing the removal of metals and acidity. The research effort addressed the problem both at a fundamental science level and at the more empirical pilot plant level. Whereas there are numerous anaerobic sulfate reducing reactors in operation on mine waters that remove some sulfate together with metals and acidity, these are typically plagued by low sulfate removal efficiency and gradual reductions in overall reactor efficiency with time. The South African research effort has focused on understanding the fundamental microbiological and biochemical reactions that occur in anaerobic reactors filled with lignocellulosic material and subjected to high sulfate water. Hypotheses have been developed that differentiate the reactions occurring in such a reactor into groups that should be individually optimised and these hypotheses have been verified through rigorous laboratory and pilot scale studies. The results of this research are incorporated into a patented multi-stage integrated passive treatment system that is capable of sustained high rate removal of sulfates, metals and acidity.

Jan 1, 2003

By Tozawa K, Nishimura T, Sasaki K

Liquidus surfaces in a part of the systems ZnO-PbO-Si02 and ZnO-"FeO"-SiO 2 were constructed by the quenching method. The ex- periments were carried out in air in the system ZnO-PbO-Si02. In the part investigated the primary phases were three ternary compounds (PbO.ZnOòSiO2, 2PbOòZnO.2SiO2 and barysilite), three lead silicates, Zn2SiO4 and SiO2. Iso- therms on the liquidus surface of each primary phase field were determined from 750 to 1300¦C. In the system ZnO-"FeO"-SiO 2 the experiments were carried out in an atmosphere of purified nitrogen. In the part investigated the primary phases were Fe2SiO4, Zn2SiO4 and Si02. Iso- therms on the liquidus surface of each primary phase field from 1150 to 1300¦C and the ternary eutectic (1130¦C, 15.9% ZnO, 48.2% "FeO" and 35.9% Si02) were determined.

Jan 1, 1980

By Y Hansen, J Petrie

Life Cycle Assessment (LCA) is increasingly being used as a decision-support tool within mining and minerals processing and metals production. However, a number of initiatives have highlighted the current limitations of LCA to accurately reflect the environmental performance of minerals and metals. These programs include:the Mining, Minerals and Sustainable development project (Stewart, 2001); the United Nations Environment Programmme/Society for Environmental Toxicology and Chemistry (UNEP/SETAC) workshop on LCA and metals (NRCan, 2002); the UNEP SETAC Life Cycle Initiative; and the review of the existing ISO 14 040 set of environmental management standards. Together, these initiatives highlighted concerns relating to the ability of LCA to engage with and support metals recycling, to adequately reflect the impacts associated with products from a multi-product orebody, the ability to adequately reflect the toxicity potential of metals in the natural environment and the fact that resource depletion focuses on mining (and not consumption) as the depleting activity in the life cycle of a metal. Additional impact categories to be included in LCA were also suggested. In this paper we demonstrate how existing initiatives are addressing LCA limitations. Finally we present the state of the art in Life Cycle Impact Assessment (LCIA) for two impact categories:resource depletion; and impacted land footprint for solid wastes.

Jan 1, 2004

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

In the retreatment of an old tailing dump containing five per cent of lead principally as lead sulphate, the lead sulphate was floated with liquid Aerofloat reagent after sulphidising with phosphorous pentasulphide in an acid circuit. A zinc middling product was removed by flotation before recovering the lead. Concentrate products were sundried in surface dams.INTRODUCTIONDuring the period between 1917 and 1928 the Junction North Broken Hill Mine N.L. deposited several tailing dumps on its leases, which were acquired by North Broken Hill Ltd.in 1931. One of these dumps lay alongside a main road close to a residential area. The high metal prices prevailing in the post-war years (1945 onwards) provided a strong incentive for retreating this dump and transferring it to a less objectionable site.SAMPLING AND TESTINGIn 1946 a sampling and testing campaign was instituted which culminated in 1949 in a decision being made to erect a tailing retreatment plant adjacent to the dump.The dump was sampled with a 3 in. post hole auger using extension lengths of -! in. pipe for drilling to 30 ft. The dump material was fine and moist and core recovery was excellent. Hole depths ranged from 14 ft. to 30 ft., with an average dump depth of 20 ft.Individual samples were prepared from successive 9 ft.lengths of core and each sample thus obtained was, submitted for sizing and assay.The sampling showed that the dump contained approximately 380,000 tons of fine tailing assaying:

Jan 1, 1956

The Proterozoic Pb-Zn deposits of the Gulf of Carpentaria, Australia, include HYC (McArthur River), Mt. Isa, Dugald River, Lady Loretta and Hilton. Two seamingly incom- patible depositional models have been proposed to account for their origin. Finlow-Bates (1980), Large (1983) and Russell(1983) classify these-deposits as sediment-hosted submarine exhalative deposits. This class includes Rammelsberg, Meggen, Silvermines, Sullivan and others. In contrast, a lacus- trine, shallow-water origin has been advocated by Williams and Logan (1981), Logan and Williams (1984), Muir (1983) and Eugster (1985). The discrepancies between these two models can be removed by creating a separate class, that of continental sediment-hosted exhalative deposits.. HYC., Mt. Isa and Dugald belong to this class and their sediments were deposited in shallow, alkaline lakes. Metal- rich, hot, Na-Ca-Cl brines entered the basins along boundary faults and interacted with pore fluids and sediments, depositing-Cu-Zn-Pb sul- fides. Similar brines entered the Lady Loretta basin after marine flooding, depositing sulfi- des and barite, placing Lady Loretta into the class of marine Sedex deposits.

Jan 1, 1987