Search Documents

Using a new type of laser surveying instrument named Particle Dynamics Analyser (PDA), the distributions of the radial and axial components of the mean velocity, the size and the concentration of solid particles at selected positions within a transparent hydrocyclone were directly measured out for the first time, from which profiles of the flow field of solid particles were obtained. And some new points were put forward such as the locus of zero vertical velocity (LZVV) of solid particles was not the same as that of liquid, and some particles in inner helical flow could also be separated. The results are of great significance to farther ascertain the separation principle of hydrocyclones and improve the separation efficiency.

Jan 1, 1993

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

It is a great privilege to be invited to give this address at this centenary conference. A centenary is a time for recollection, for celebration and for looking ahead. The AusIMM has much to celebrate and many things to recall. I hope in this address to make some useful comments about Australia's future (and mindful of but not forgetting New Zealand), looking ahead for 25 years or so, and the mining industry's role in that future.

Jan 1, 1993

The Pacific Rim and its environment involves a vast array of natural phenomena, and a vast array of situations which show the impact of man. Almost half the world's population of over five billion live in nations" which border the Pacific, but the concentration is focussed in the North. Great experiments are occurring in this region, the industrialization and energy development in- Japan and China, the growth of Indonesia, (now 168 million - soon 368 million; Brown and Jacobson, 1986), the enormous developments of agriculture and the metals resource base in Australia and China. At the same time, the Pacific Rim does not project images of hopelessness, the mood is upbeat. Over the past decade, incomes have increased substantially in most of the major countries of Pacific Rim (e.g. over the period 1980-86, + 58% in China, + 21% in Japan, + 34% in South Korea; Brown and Jacobson, 1986). In September, 1986, at the general assembly of the International Council of Scientific Unions (ICSU) in Bern, Switzerland, representatives of over 50 nations approved a new initiative, "The International Geosphere Biosphere Programme: A Study of Global Change". The focus of this new program is "To describe and understand the interactive physical , chemical , and biological processes that regulate the total Earth system, the unique environment that it provides for life, the changes that are occurring in this system, and the manner in which they are influenced by man. The IGBP will be a tightly-defined programme of research, directed at providing fundamental knowledge that will serve as a basis for assessing likely future changes on the Earth in the next 100 years" (ICSU, 1986). For the earth scientist, and all resource scientists, there is an emerging agenda; new priorities are appearing, new questions are being asked. The recent report of the World Resources Institute (1986) focusses on this emerging agenda. Topics which are at centre stage in this report include the following: The environment and human health Tropical deforestation The atmosphere as a shared resource and climates Soil-degradation Rural-urban migrations Food and agriculture The diversity of species-ecosystems Freshwater as a finite resource Coastal areas and resources

Jan 1, 1987

In December 1997, a series of new environmental legislation was enacted including:ò Environmental Planning andAssessmentAmendmentAct 1997; ò Contaminated Land ManagementAct 1997;ò Protection of the Environment (Operations) Act 1997; ò Native Vegetation Conservation Act 1997; andò Pollution Control (Load Based Licensing) Act 1997.These new Acts will have varying degrees of impact on the coal mining industry in New South Wales when they commence later this year.

Jan 1, 1998

One of the more recent developments within the mining industry has been the adoption of formal continuous improvement programs. A continuous improvement (CI) program was launched across Kalgoorlie Consolidated Gold Mines (KCGM) in early-2002. The purpose of this program was to identify further operating improvements within departments. The focus of the continuous improvement program was not only on the areas of the operation which were performing below expectations but also on areas of the operation which were performing well but could still be further improved.The effectiveness of a continuous improvement program depends on the stability of the processes in place and the participation of many employees from all levels of the business.Continuous improvement has had some successes and failures at KCGM and this paper will discuss both within the open pits department. Further improvements that could be made to the process will also be discussed. Kalgoorlie Consolidated Gold Mines Fimiston operation is located in the Kalgoorlie Goldfields and it the largest gold mine in Australia producing over 800 000 ounces of gold per annum.

Jan 1, 2004

By Lin Bin, Minggao Qian, Zhiyi Yang, Fullan He

There are no efficient methods and instruments available in China at present for diagnosing the leakage problem for a hydraulic support system in underground coal mines. A new method has been developed to solve the problem. It is proposed that

Jan 1, 1998

Gold occurs at Mt. Charlotte associated with a stockwork of pyritised quartz veins in Unit 8 of the Golden Mile Dolerite. The ore- body is massive, 200m long and 40m wide and has been proved to over 600m below surface. Mining is by sublevel ring drill stoping with the ore recovered by diesel powered equipment. Ore reserves are based on traverses of diamond drill holes oriented to produce an equal intersection width on the two principal sets of quartz veins. Assay and geological boundaries are marked on each drill section and this boundary is transferred to mine plans and cross sections. Ring-drilling patterns are based on the cross sections and the resulting mining outline is transferred back to the drilling sections. The mine ore reserve is calculated from the mining outline.

Jan 1, 1979

By Tran T

The kinetics of cementation of silver chloro-complexes from sodium chloride solutions onto copper and zinc was studied using rotating disc electrode system. The activation energies were found to be 10.8 and 30.5 k7/mole, in a 3M NaCl solution on copper and zinc discs, respectively. Higher dissolution factors were obtained on zinc disc, due to hydrogen evolution, whereas, copper dissolved close to the predicted values. Scanning electron microscope studies were conducted both on copper and zinc- cdiscs-to evaluate the deposit morphology and its effect on reaction kinetics. Two stage deposit growth was observed both on copper and zinc discs. Smooth, coherent initial deposit followed by tree-like secondary dendrites formed on copper, whereas, scattered bulbous initial deposit followed by porous dendrites was typical on zinc disc.

Jan 1, 1992

By N Wharmby

In recent years in New Zealand there have been a number of tunnelling and deep directionally drilled pipelines projects that have required access shafts. Often these shafts are in urban environmentswhere vibration and high noise levels are not tolerable. There are a number of methodologies that can be adopted dependent upon the shaft plan area, depth and geology.This paper will describe some different methodologies that can be adopted that use piling methods such as large diameter piles, and secant piles. The paper will use case studies to highlight:· construction methodology,· specific methodology issues and constraints,· lessons learnt, and· recommended specifications.The development of piling technologies in New Zealand has enabled the development of cost effective solutions for the construction of deep shafts in sensitive urban environments.

Mar 8, 2011

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

By D Elder, S Bell

Over the last five years Solid Energy New Zealand (SENZ) has gone through a series of changes in response to both external and internal factors. These changes have included corporate reorganisation and funding restructure, as well as modifications to medium and long term business objectives. The nature and size of its coal reserves and markets requires SENZ to continue developing new mines as existing mines are depleted. As well, there are opportunities to develop new mines as coal markets change or to realise value from existing coal resources. To assist in this process, a set of mine project assessment guidelines which are relevant to the size and scale of anticipated mine developments have been developed for SENZ. These project guidelines are structured to operate from the early stages of project or resource review through to final feasibility study stage. The guidelines provide both a basis for planning and budgeting, and a control mechanism within the company. They also enable clear understanding of the status of individual projects and provide a framework for comparison between projects. SENZ now has a defined method to plan, monitor and control this important aspect of its business. The paper explains the development and structure of the guidelines, as well as providing examples of their application. and use. It demonstrates how SENZ integrates its long term planning, five year planning, annual planning, project planning and risk management to maximise the value of individual projects, business units and the company overall in a consistent manner.

Jan 1, 2002

By D E. Langberg, J S. J va, D R. Swinbourne

Specifications on the types and levels of impurities tolerable in metals are becoming increasingly stringent, and are pushing the limits achievable with conventional refining technologies. Particularly difficult is the removal of electrochemically noble elements with low volatilities, such as copper, from more active host metals such as lead, iron and aluminium. Electrochemical refining, utilising the ability of certain solid electrolytes to selectively transport copper or other impurity cations away from the molten host metal into a separate refining phase, may provide an answer to this problem. Numerous studies on solid electrolytes used in concentration sensors have been reported, as well as a limited number on metal refining. Oxygen anion conducting solid electrolytes have been applied to the deoxidation of copper and steel while cation conductors, eg ¯ -alumina and Nasicon materials, have been used to remove lithium and sodium from aluminium. However, solid electrolytes have yet to be applied to the removal of noble elements. The behaviour of solid electrolytes under the extreme conditions of molten metal refining is not well understood. This paper will examine the potential use of solid electrolytes to remove noble metals such as copper from active host metals such as iron. The suitability, and selection criteria of available solid electrolytes for implementation in the metal refining industry in the future will be discussed. In particular, the stability of Cusicon, a copper superionic conductor potentially suitable for use in metal refining, has been assessed and the results of the experiments are presented.

Jan 1, 2000

Today, more and more tunnel ventilation systems are based on NO2 (or NO) and visibility measurements. Due to the significant decrease of CO emissions in countries with EU emission standards, which were adopted by Australia in 2004, CO is no longer a key factor for tunnel air quality monitoring and is often only measured for plausibility reasons (eg according to the German guideline RABT2006). Nitrogen dioxide, which is a good indicator for the overall air pollution along roads, is now taking over the leading role not only for ventilation control but also for air quality monitoring and in future probably for checking the function of air filtration plants in tunnels. Due to the lack of equipment for reliable and long-term NO2 measurements in road tunnels in the past, there are only very few standards giving limit values for NO2 in road tunnels. Furthermore there are not many records of NO2 readings over longer periods in different types of tunnels. SICK MAIHAK, a major supplier of measurement devices for controlling tunnel ventilation, has introduced the first monitor in 2006, specifically designed for measuring NO2, NO and visibility simultaneously in road tunnels. There are now experiences and results from the first tunnels equipped with this kind of system. This paper will present and discuss the results and experiences from these tunnels and explain the different levels of NO2 in different tunnel types. Furthermore, the status of air quality standards for road tunnels regarding NO2 limit values and the current status of discussion in various countries about NO2 limits will be presented.

Jan 1, 2008

By D Langberg, R Taylor

Many metallurgical operations produce fine residues and dusts as by-products which can be difficult to handle and offer little direct financial incentive to treat. There is a growing imperative to deal with these materials particularly since land fill is fast becoming an uncertain long term solution. One possible means of treatment is to extract the valuable metals while fusing the remainder into a slag. In this way valuable metal components of the material can be recovered and the less valuable components be converted into useful products, eg cements and inorganic polymers which have a high environmental stability and a growing market. The aim of this project is to establish solids injection and fusion in a slag bath as a viable method of treating industrial wastes and residues. The benefits of this approach are expected to be: the ability to treat a wide range of organic and inorganic residue materials, ease of recovery of volatile and valuable elements and the production of final materials which could be used in other industries. In ongoing experimental work at the CSIRO Minerals a 250 kg slag bath reactor has been used to test the injection of Paragoethite residue into an iron silicate based slag. An experimental apparatus has been designed and commissioned to pneumatically inject solid material at feed rates of up to 80 kg/hour. The capture efficiency of injected solids by the slag bath was calculated by monitoring the composition of the slag. Using this method of treatment, the zinc contained in the residue can be recovered as a fume by varying the oxidation state of the slag. Other valuable elements could be recovered by creating a matte or metal phase in the reactor with the final material being used in the production of cement. A capture efficiency of injected solid paragoethite particles in the slag bath of up to 97 per cent was achieved. Under the conditions of the experimental work capture efficiency was found to be independent of injection velocity and slag depth. The rate of fuming during injection was found to increase slightly with injection velocity and was independent of slag depth.

Jan 1, 2002

By E Topal

Risk and uncertainty are attached to mining projects, and making decisions, hedging, future investment and evaluation of mining projects depend on forecasting the future price. The future technologic developments in mining will be primarily influenced by the future commodity prices. A few approaches, with different confidences are proposed to predict price movement in the future. This research introduces a new comprehensive version of the mean reverting jump diffusion model for natural-resource commodity prices. The novel model proposes that the historical data of mineral commodities have three terms to demonstrate fluctuation of prices: mean reversion component, diffusion component and jump component. The model calculates each term individually to compute the future prices of mineral commodities. Subsequently, in the second section of the paper, the model is implemented for monthly historical data of gold price from January 1968 to May 2008. This research is investigating the relationship between the historical oil price and inflation with the gold price. This is followed by a future estimation of gold price fluctuations up to 2018. The results from the application of this new method are discussed in the context of how they accurately replicate the historical gold price and how they can predict the future gold price.

Jan 1, 2008

By Yu H, Wan B

40 percent of the coal reserves and 40 percent of the ouput of coal in China is of thick coal seams. The sub-level caving in Yangguan has evolved together with the hydraulic supports, to provide recovery rates today of 80 to 85 percent, waste ratios less than 10 percent and daily outputs exceeding 7,000 tonnes. Matching of rate of shearing bottom coal to caving of top coal is most important to achieve "simultaneous" operations. Spontaneous combustion in the goat, gas, including in the goal, and dust, are particular safety hazards which are combatted with various stringent measures.

Jan 1, 1991