Search Documents

When mining of ilmenite deposits wet process of preparation is traditionally used. But this method needs large volume of water. The problem of water deficiency is characteristic of many regions of the Republic of Kazakhstan. The Satpayevskoye ilmenite deposit is situated in the East Kazakhstan, its location has problems with water, and the mineralogical composition of rock is unfavourable: rocks contain up to 40 per cent of clays. That is why designers made a decision to use dry process of preparation for processing of these ores. Offered scheme and equipment selection are presented in this paper.

Jan 1, 2003

By Hughson B

The need to prevent the sterilisation of coal stems directly from the fact that it is a non-renewable resource. In N.S.W. a vast amount of coal resource is located under major public utilities such as freeways, railways, stored waters, pipelines carrying gas, water and sewage, and transmission lines. Total extraction has occurred under freeways, transmission lines and pipelines with little or no damage. Where damage has resulted, the cost of restoration was only a small fraction of the value of the coal recovered. However, coal at present is being sterilised and perhaps lost for ever under stored waters and railways. If engineering solutions are available for mining under these improvements economically and with maximum safety, then coal should be extracted and utilised to the benefit of the State.

Jan 1, 1986

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

The majority of coke in Australia is made in by-product slot ovens at steelworks in Port Kembla, Newcastle and Whyalla. Most of the coals for these plants come from New South Wales but a regular proportion of Queensland coals may be introduced. The plants and the coals are reviewed in the paper.

Jan 1, 1975

The principles and practical applications of the Mogensen Sizer are examined, with particular reference to the experiences at Coal Cliff Mine, New South Wales. The Mogensen Sizer has proven to be a worthwhile alternative to conventional screening. It has the flexibility and capacity to offer a useful sizing tool, particularly in areas of confined space. It is simile in design and 1 in construction.

Jan 1, 1984

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

The story of the rise, progress, and development of our modern railway system is a long but an exceedingly interesting one. The phases it has passed through, the discussions that have arisen from time to time on the most economic modes of construction and working, and the final result these various discussions have led to, are full of importance and interest to the engineer. It is not my intention to deal historically with the subject. I desire simply to speak to the requirements of the hour in Australia. It will not be disputed, I think, that these colonies have reached a point in railway construction and management when, if additional lines to any extent are still to be built, a different principle must be adopted. There are yet large tracts and areas of country to be tapped by the rail and the locomotive, which for years to come must remain untouched if the same expensive gauges and modes of construction are continued. We have yet to see clearly the necessity of introducing a system of light lines that will pay their own way and at the same time augment the traffic of our main lines. This question really no longer remains an unsolved problem. It lies, in a few words, in the acceptance of the, narrowest gauge and the simplest mode of construction that can constitute a pacticable railway. I fear it is hopeless to suggest that private companies should be legally permitted to construct such lines. It seems as if it were next to impossible to move official authorities to enter upon the construction of lines on this principle. It is, all the same an undoubted fact that if private companies could obtain Acts of Parliament, that in several of the colonies a new impetus would be given to railway construction.I may point out that not only has the principle of narrow gauge light railways been adopted in India but private companies are obtaining power to build them. Outside of :England many narrow gauge lines have been made, and in France, Denmark, Italy, and Sweden they have been highly successful.

By Watsford RMS, Wickham P

In October 1980 the two existing flotation circuits were combined into a single new circuit. This circuit used modern 11.3 m3 flotation cells which replaced 1.4 m3 units. Sometime after this change, a significant deterioration in metallurgical performance occurred. This paper describes the work done to discover the causes of deterioration in performance and actions taken. The program implemented to prevent a future occurrence is also presented. The work included analysis of routine plant data, analysis of surveys to obtain element and mineral flows on both a sized and unsized basis, some quantitative mineralogy, and analysis of some external factors.

Jan 1, 1978

Resource developers in Papua New Guinea (PNG) are now, more than ever before, confronted with land-owner related issues that can hinder their corporate objectives.Development of PNG's custom-arily owned land since independence has brought sudden changes with mixed success. Exploitation of mineral resources has had its share of problems, and Highlands Gold Limit-ed's (HGL) endeavours in the central Highlands of PNG are no exception.

Jan 1, 1994

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

Hydrometallurgy has a history of over 300 years with copper leaching and cementation having been exploited in Spain as far back as 1670. Since then, hydrometallurgy has become an integral, expanding branch of extractive metallurgy. This paper reviews major developments in hydrometallurgy over the past century with emphasis on recent commercial developments and their impact on the mining and metals industries. The environment in which these developments has taken place has changed significantly in the past two decades and many factors, often non-technical, have emerged as constraints on the operation of existing plants and the expansion and development of new hydrometallurgical operations. Finally, a number of possible new developments that will shape the future of hydrometallurgy in the new millennium are discussed, particularly as they relate to the assimilation of technical advances in other areas of science and engineering. The impact of current trends in the education of hydrometallurgists and the provision of research in support of these future developments is also addressed.

Jan 1, 2000

Developments in mining technology are outlined which point out that longwall face technology has the capacity to produce 20,000t/d on a regular basis. The optimum length of longwall faces is about 250m. Developments of headings and gate roadwyas require radical changes to meet longwall developments. New conceptual models are outlined to meet the challenge.

Jan 1, 1988

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

AustraliaÆs current interest in renewable energy is based on a desire to reduce the countryÆs greenhouse gas emissions. Wood from sustainable sources offers a unique opportunity to combine greenhouse gas benefits with other significant environmental and social benefits, including salinity mitigation, carbon sequestration, soil replenishment and rural industry. The challenge is to make renewable energy from wood in a cost competitive manner, so that this broad range of benefits may be best realised. Bioenergy and carbon products are of great interest as new, commercial forestry products that can drive large-scale environmental tree planting:In Western Australia, Enecon has worked with Western Power Corporation to build the first full-scale plant for integrated processing of mallee eucalypts, to produce activated carbon, renewable power and eucalyptus oil. It is intended that this plant is the first of a number of such plants to help catalyse environmental tree planting in Western Australia. New technologies being developed overseas may provide competitive bioenergy in areas where traditional markets for wood do not exist. For example, pyrolysis converts wood into a bio-oil that may be transported to remote sites for power generation in gas turbines. Pyrolysis also produces wood char. Pyrolysis and wood-to-ethanol technologies, coupled with short rotation coppicing trees, offer the long-term prospect of large-scale production of renewable fuels around the country.

Jan 1, 2006

In the mining and minerals industry, development, introduction and construction of new plant designs, to meet sustainability objectives, face a series of major hurdles. Typical are the long investment cycle times, the designer does not normally control the spending (the owner does), and the industry is inherently technologically conservative or risk adverse while accepting the often more significant geological, market and political risks.æSustainable Plant DesignÆ is an approach to plant and facility design that drives the necessary culture change and acceptance by minimising technical risk and maximising potential returns. The approach forces consideration of sustainability objectives and risks early in the project, where cost saving and efficiency improving opportunities can be maximised.In Hatch, we are using three proven tools under the ærisk managementÆ umbrella to drive sustainable development principles into our projects:Sustainable Plant Design, FutureWatchTM Reviews, and Clean Plant DesignTM . These proactive practical, not theoretical, techniques for driving change from within and reducing whole of life cycle costs will be discussed and illustrated with case studies.

Jan 1, 2004

Accidents in open pit mining have a high cost in lost time of person- nel, damage to equipment and installations, and lost production. The realities of export competition require that Mine Management sig- nificantly reduce the costs associated with accidents and workplace ill-health. Newer management approaches are proving effective in reducing the Total Cost of Risk through a strucured Occupational Health and Safety Programme exhibiting the following features: ò Formal Company Policy ò Accountability for OH&S performance clearly designated to each level of management and supervision ò Effective utilisation of a Mine Occupational Health and Safety Co- Ordinator and a Mine Occupational Health and Safety Adviser ò Development of realistic OH&S Objectives ò Training of Management, Supervision and Workforce in Occupa- tional Health and Safety ò Development and adoption of Safe Work Practices and Procedures ò Effective employee selection procedures, control of Contractors ò Monitoring of the health of the workforce ò Collection, recording and distributing information on all Mine inci- dents, accidents, injuries and damage ò Ensuring that the Mine environment is healthy and safe ò Effective Emergency Procedures to deal with injury, fire, rescue and other situations of risk ò Controlling those Mine hazards which cannot be removed ò Adopting a high standard of Occupational Rehabilitation ò On-going visible Management participation in the programme to ensure that momentum is developed and maintained. This approach requires that Occupational Health and Safety be given equal status with product quality, maintenance of plant and output per- formance; its implementation is rewarded with improved morale and major cost reductions.

Jan 1, 1989

The role of marketing in the development of a new project will be affected by political, commercial and technical pressures. Marketing success will be determined by the ability to predict and react to tomorrow's environment. In the Australian coal industry there is an emerging transition from production to marketing orientation. As a result, greater technical awareness of customer needs will be required. In particular, the industrial product nature of coal markets will need to be recognised. Greater attention will also need to be paid to product options and quality in mine planning. Marketing personnel will become more involved at every phase of the development of a new mine.

Jan 1, 1983

By M Zoorabadi, Y Zhang, D Bringemeier, S Nicoll, N Kerr

Lihir operations of Newcrest Mining Limited (NML) are on Lihir Island (PNG) which is located approximately 900 km north-north-east of the national capital Port Moresby. The mine is located within the Luise Caldera of the Luise Volcano which is located on the east coast of the island. The caldera is an extinct volcanic crater that is geothermally active. Volcanic activity on Lihir Island is limited to remnant hydrothermal venting in the Luise Caldera in the form of hot springs and fumaroles. Steam and gas (including H2S) naturally discharge within the pit area and along the Kapit beach and near shore region. The hydrothermal reservoir temperatures can reach 100°C at the water table and exceed 200°C at depth. Newcrest maintains a Geo-hazard Management Plan to identify and manage the various geotechnical and geothermal hazards on-site. The major geothermal hazard to mining at Lihir is the occurrence of geothermal outbursts, which have occurred in the past with varying intensities and caused two ‘near misses’, production delays and material losses.

Nov 29, 2022

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014