Search Documents

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

By D Luppnow, C Hore

In-pit tailings storage can provide many advantages when compared to typical above-ground tailings storage facilities (TSFs). As regulations become more restrictive and existing mines expand into new pits, the motivation and opportunities for in-pit tailings disposal is increasing.The Langer Heinrich uranium orebody follows a palaeo-river channel and is mined as an open pit operation. The mine pits intersect two main aquifer systems, one at the surface and one at the base of the orebody/pits. The tailings storage methodology is full in-pit disposal in multiple TSFs for the life-of-mine. Continuity of the initial hydrogeological conditions is incorporated in the design by the use of the pervious surround concept and the reinstatement of the lower aquifer (palaeochannel aquifer) at the base of the pit. Containment embankments are required to facilitate the staging of the TSFs development and are constructed using waste rock liberated during the mining of the pits. All of the TSFs are equipped with decant structures and an underdrainage system is included to improve water recovery, enhance consolidation and increase tailings density.This paper presents the design of a unique in-pit tailings storage solution for the Langer Heinrich mine in Namibia owned by Paladin Energy Ltd.CITATION:Hore, C and Luppnow, D, 2015. In-pit tailings disposal at Langer Heinrich – tailings storage facilities in a unique hydrogeological setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Salaya, J Kwak, L Keeney, S Dehkhoda

In addition to volatile commodity prices influencing decision making, in recent years, social and environmental performance have become important decision drivers within the mining industry. There are increased demands from stakeholders, communities, and governments to ensure that raw materials are mined, processed and refined responsibly. The industry also faces the challenge of better managing its waste, which has led to severe consequences when not done properly. The high commodity prices of the late 90s and early 2000s encouraged larger economies of scale and drove mining companies to extract large volumes of rock for separation and concentration at the downstream processes. Over time, as ore grades dropped, the cost of mining escalated and tailings volumes grew. This arduous process also caused strains on recovery cost and performance. Scarcity of water and energy resources coupled with increased production demands and higher operating costs are putting pressure on companies to find innovative ways to increase mining intensities. Hatch’s value chain optimisation methodologies, specifically Grade Engineering® and early waste rejection of the mine, have been of interest to intensify operational performance and minimise waste generation. Enabling preconcentration of the plant throughput, the methodology has significant potential to improve overall metal production and reduce water and energy intensities, whilst minimising wet tailings. Using representative data from real world mines, this paper reports on a case study that evaluates the impact of preconcentration using sensor-based ore sorting on downstream process improvements as well as energy, water and tailings reduction. Financial and economic viability of this technique is presented for both brownfield and greenfield implementation cases. The results show that business case for preconcentration is best when: the distribution of metal in the run of mine ore is negatively skewed and left tailed; mining costs are low; energy, water and tailings management costs are high; and low cost methods of recovering pay metal from low grade material are available.

Nov 10, 2020

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

By D R. Seaman, B Adamson, P Sharman, M McMahon

"The Telfer processing plant commissioned its pyrite regrind and flotation circuit in August 2012. The circuit was designed to regrind pyrite concentrate to a p80 of <30µm then float a gold and copper rich concentrate before tails from the flotation circuit fed the carbon-in-leach (CIL) circuit downstream. Expected benefits were: improved CIL performance that would result from the finer grind and a reduction in cyanide soluble copper to the CIL circuit, as well as a small increase in overall flotation circuit recovery. While the benefits of a finer grind were soon realised, recovery in the post-regrind flotation circuit (named the ‘pyrite recleaner circuit’) was consistently and significantly lower than that expected based on laboratory test work. Selectivity in the pyrite recleaner circuit was virtually nil and copper reporting to the CIL circuit did not change as a result of the pyrite recleaner circuit operation.A pulp chemistry survey of the plant and comparison with the lab showed that the dissolved oxygen (DO) demand in the plant was much higher than that in the lab. Lab flotation tests conducted using nitrogen gas instead of air resulted in recoveries similar to those from the plant. It was identified that the freshly ground pyrite surfaces exiting the regrind mill were consuming oxygen in the slurry and there was insufficient oxygen available for collector adsorption and pyrite depression to occur. Test work, using a pilot regrind mill, showed that a reduction in grind size resulted in an increase in DO demand.A range of oxidising agents were tested in the laboratory and using a pilot flotation rig set-up in the plant. Oxygen was found to be the most reliable and effective agent and options for increasing oxygen delivery to the plant were explored. Scale-up from the lab oxygen requirement to the plant is difficult and efforts to implement a permanent solution for meeting the DO demand in the plant are ongoing.Citation:McMahon, M, Seaman, D R, Sharman, P, Adamson, B and Seaman, B A, 2016. Optimising the Telfer Pyrite Regrind Circuit - Effect of Dissolved Oxygen Demand, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Forbes, R Jeuken

Brownfields geoscience measurement such as drilling and surface geophysics can be costly and it is often difficult to weigh the cost of data collection and processing against the value it unlocks at the time of extraction. This makes it difficult to prioritise geoscience expenditure and find the optimum intensity of geoscience activity across competing assets. There are multiple options for managing resource uncertainty and spatial variability through mine planning and resource engineering such as varying marketing strategy, adjusting stockpile or other infrastructure design and product blending. Consideration of these alongside increased data collection further complicates finding a comparable value of geoscience programs to determine the right blend of geoscience measurement and engineering controls. Concepts similar to Value of Information (VOI) analysis which is applied to strategic planning can be used to estimate the value of geoscience measurement and pit sequencing at tactical planning and operational timescales. This involves the quantification of resource uncertainty and prediction of how it will affect resource extraction. This paper outlines this process and demonstrates its use to prioritise geoscience at BHP Coal Assets. The value of infill drill programs in enabling operational stability is quantified and compared the value of engineering controls like increased stockpile capacity. This study supports that idea that the application of VOI methods to bulk mining at tactical time horizons has potential to inform geoscience planning and resource engineering not just separately, but as part of a unified strategy for managing resource uncertainty.

Mar 22, 2022

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

By L Rachmad

Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) deposit which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. Evaluations were made on former block caving mines at PT Freeport Indonesia (IOZ, GBT Area I and II) in order to design a more appropriate support system. As a permanent support, the thread bar bolt support system is widely used in the DOZ mine. The advantages of this system are ease of operation, quality control and high bond strength. The main problem of this system is the curing time of about 28 days to achieve maximum strength, necessitating the installation of a temporary support for its implementation. In this instance, the system was inefficient in operation and studies were required to find an alternative grouting system. This paper examines the evaluation of thread bar bolt support system and compares the performance of two types of grouting (resin cartridge and cement cartridge) with cement grouting performance. The evaluation is conducted with a pull out test. The advantages and disadvantages for each grouting method, comparison of cost estimation and grouting application in mine scale are presented in this paper.

Jan 1, 2002

By B Dodd

This paper details how the Australian Securities and Investments Commission (ASIC), as a disclosure and conduct regulator, approaches regulation of continuous disclosure, capital raising and control transactions in the mining and resources sector, and the reasons for the approach. In examining this topic the paper considers the Joint Ore Reserves Committee (JORC) Code (JORC, 2004), the VALMIN Code (VALMIN Committee, 2005), the relevant ASX Listing Rules and the relevant provisions of the Corporations Act 2001 (Corporations Act). This paper discusses ASICÆs approach to expert reports and disclosure with reference to Regulatory Guides 111 Content of expert reports and 170 Prospective financial information.CITATION:Dodd, B, 2012. Issues in capital raisings and disclosure, in Proceedings International Mine Management 2012, pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Bruce

OZ Minerals’ Carrapateena mine is a Sublevel cave mine located in South Australia, approximately 160 km north of the regional centre of Port Augusta. Carrapateena commenced underground development in 2016, with production commencing in 2019 and ramping up to 4.25 Mtpa by December 2020. In pursuit of continual improvement, the Carrapateena mining team sought to identify how it could better interrogate its current productivity levels and its drivers (root causes). During this process the team were confronted by a disconcerting number of different opinions (which often conflicted) on our actual productivity performance which led to a need for review. Although reliable data and a well-designed time utilisation model (TUM) existed, it was still unclear what actions needed to be put in place to improve productivity. This was for the following reasons: • Data sources were disparate unless significant effort was applied to compile them. • Data sources were not available in a format that could be easily viewed or analysed. • General understanding of the data which was collected and how it could be used was poor. • Process of regularly analysing performance and forming tangible actions to improve was lacking rigour. A project was then started with the goal to fix the areas stated above. An initial requirements gathering exercise was undertaken to identify key data sources for site which returned a staggering 42 known systems which were then shortlisted to the key systems that contained operational data and could generate tangible improvements when analysed. This paper discusses the approach to selecting the OZ Minerals Insights Hub as the chosen platform, and the effort and collaboration between cross-functional departments that was involved in transforming the data so it could be displayed in a useful way. The data sources identified included a fleet management system, two planning databases, a control system historian, and a mobile fleet machine data system. New processes were also introduced to digitally capture daily commentary; this was achieved utilising SharePoint Forms. Data pipelines were then developed in the Insights Hub platform to automate the ingestion and transformation of the raw mining data into curated data models for end user consumption. Tableau dashboard packages have been created to support facilitation of short interval control, daily review meetings, and weekly review meetings as well as data analysis of key equipment and locations. These dashboards visualise the mining data models in a form that provides the user a clear picture of what has occurred, why it has occurred, and where to focus improvement efforts. This has resulted in a team which is more accountable, more equipped to assess the root cause of performance, and more regularly able to make data driven decisions. The next step? To build this out from Mine to Mill and create a data indexing tool which will drive self-service reporting, a data agnostic platform and predictive tools that help our people continue to be one step in front.

Mar 29, 2023

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By J-S Zhang

In this paper, the author briefly introduces the resource characteristics of Chinese iron ore, as well as the present increasing market demand for iron concentrate. The SHP-3200 wet high-intensity magnetic separator (HIMS) is used to separate complicated weak-magnetic iron ores being composed of specularite, limonite and siderite in Jiuquan Iron and Steel (Group) Co Ltd. Some technologies have been used to improve SHP-3200 HIMS, including modifying the angle of magnetic polar from 90¦ to 83¦, cooling the exciting coils by oil instead of air, adding reverse-washing equipment to wash off magnetic particles and adjusting the tooth-space of the matrix from 5.0 mm to 3.5 mm or 2.5 mm to enhance the recovery of fine particles. It is still difficult to meet the requirement for recovering more difficultly separated iron and the demands for high-grade concentrate of iron. In order to improve the recovery of difficult-separated iron, the film-magnetic separation technique is applied into the HIMS and a new LY matrix is designed to form magnetic gradient vertically. A flowing-film feeder is also added and the feed mouth is modified to make a slurry flow formed in the form of film along the wall of matrix. The microstructure and dissemination character of the mineral particles is studied, and the specific susceptibility of the primary minerals is measured. Then the distributive characteristics of a magnetic field for the separator with film-magnetic technique and the motion of particles in the process of separation are all analysed. By introducing the film-magnetic separation technique to SHP-Φ700 HIMS, the recovery of iron can be raised from 69.45 per cent to 76.07 - 78.96 per cent with the similar grade of concentrates of iron. Such an increase of 9.51 per cent in the recovery also shows that it is feasible for such film-magnetic separation technique to be applied into HIMS.

Jan 1, 2005

By J Seery, N Savage, A Wilson, L Nicholas

Geological modelling provides a means of spatially representing the three dimensional distribution of geological information to downstream stakeholders. The geologist completing the modelling work intimately understands the varying degrees of confidence, assumptions and extrapolation required to honour the data. Geological models are often taken and used by stakeholders without fully understanding this modelling process. This can lead to confusion amongst stakeholders when the geological model shows variable reconciliation. A method for visually communicating the confidence of the spatial distribution of geological models has been created by the Rio Tinto Iron Ore structural geology group for use primarily in geotechnical engineering investigations. A numeric confidence rating is assigned to each geological data point used in the creation of a geological surface. This is based on data type, collection method and reliability to indicate potential error in distance from its modelled location. In regions of sparse data, confidence ratings are inserted based upon the geologistÆs experience and knowledge of the geology, whereas mapped geological contacts or drill hole intersections are assigned a higher confidence rating. A regular grid of points is registered to the geological surface and each of these grid points is assigned a confidence rating using an inverse distance weighting using a nearest neighbour approach. The resulting grid is colour coded according to the confidence rating to provide a visual representation of the variable confidence of the geological surface in three dimensions. Subjectivity and bias from the geologist is minimised by critically analysing the input geological data and then applying this methodology to represent the confidence in the spatial characteristics of geological models. Understanding of this confidence enables mining professionals to make informed decisions and identify areas that require further geological investigative work. CITATION:Savage, N, Nicholas, L, Wilson, A and Seery, J, 2013. Visual communication of geological confidence - a move toward a less subjective approach, in Proceedings Iron Ore 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Safe, efficient production is a common objective for all large open pit mines. Despite comprehensive policies, procedures and regulations aimed at protecting workers, several people die each year in mining equipment-related collisions. The limited sightlines of heavy equipment operators coupled with difficult operating conditions are major contributing factors to the majority of mining equipment collisions. Off road haul trucks are the most common type of machinery involved in surface accidents. These vehicles represent the primary target for improving safety performance by mine operators. Although several commercial products have been introduced to address these issues, none have achieved significant market acceptance. The current collision avoidance solutions lack integration with onboard fleet management and equipment health systems. To achieve acceptance in industry, any collision avoidance system must offer high reliability, minimal false alarms, and value for money. With these criteria in mind, this paper will examine the pros and cons of the various technological approaches to collision avoidance in an open pit mining environment. The unique global positioning systems (GPS) and camera-based proximity detection solution on offer from Modular Mining Systems will be described. This solution uses intelligent filters to minimise false alarms. Tight integration with fleet management provides context information to enhance warnings and enable back-office near-miss analysis. Available today, this combination creates a practical solution to improve the situational awareness of heavy equipment operators, at a compelling price point. Future directions for maximising heavy equipment operator situational awareness will also be examined.

May 1, 2010

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By Siemon J. R

It is possible to use compacted anodes formed at low pressure for the direct electrowinning of lead from sulphide concentrates. An anode containing 5.5 per cent graphite, formed into a compact at 34 MN m-2, enables lead to be won at a current efficiency of about 80 per cent; the power consumption .at 150 A m-2 current density being 0.4 kWh per kg lead. It would be necessary to use diaphragm cells to obtain a sufficiently pure product. A conceptual design for a full-scale plant is presented, together with a cost estimate for the production of lead by a process based on direct electrolysis of compacted concentrates. It is unlikely that the proposed process will be economically competitive with the conventional lead smelting.

Jan 1, 1976