Search Documents

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

By D Morton, G Wallace

"Evolution Mining is the sole owner of the Mt Rawdon open cut operation, located 75 km south-west of Bundaberg in Queensland, Australia (Figure 1). It is a massive, volcanically hosted, low-grade gold deposit that exhibits excellent characteristics conducive to low cost mining and treatment.In 2014, Mt Rawdon began investigating initiatives to deliver higher mill throughputs without any significant capital expenditure or modifications to the existing processing plant. Various studies have shown throughput increases are possible by applying more blast energy, essentially by reducing feed size through blasting and leaving less work for the comminution circuits (Brent et al, 2013; Ziemski, 2011; Workman and Eloranta, 2003).Given that 53 per cent of energy used on a mine site is consumed by the comminution circuit, with only two per cent being consumed by drill and blast (Smith, 2013), it makes logical sense for a mining operation to align their drill and blast with their processing plant. The term commonly used when exploring this relationship is a ‘Mine to Mill’ program.Over nearly 12 months, various blasting options and Mine to Mill methodologies were tested at Mt Rawdon. Throughout the journey, it was abundantly clear that the Mine to Mill initiative is not as simple as making one technical or physical change and expecting an improvement. Rather, true sustainable improvements demand a paradigm shift across both the mining and processing cultures, where all departments are aligned and working towards the one outcome. This true overarching Mine to Mill mentality, enabled by Vistis™ 250 high energy bulk explosive, ultimately led to a sustained increase in throughput and profitability of the Mt Rawdon operation.Citation:Wallace, G and Morton, D, 2016. High Energy Bulk Explosives and Mine to Mill Focus – the Mt Rawdon Story, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 60–69 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Miller, M Dowling, R Domotor

"This paper is focused on blasting activities undertaken as part of the Pacific Highway Upgrade – Tintenbar to Ewingsdale – project (T2E). This is a ‘priority 1’ Pacific Highway road construction project in New South Wales (NSW), to be completed by mid-2015 (weather permitting). T2E will provide approximately 17 km of dual carriageway road starting at the northern end of the Ballina bypass and extending to the Ewingsdale interchange, and will complete the existing dual carriageway road between Ballina and the NSW/Queensland border.Roads and Maritime Services (RMS) (formerly the Roads and Traffic Authority) is delivering the project on behalf of the NSW state and federal governments. In October 2011, RMS awarded a contract to Baulderstone Pty Ltd (now Lend Lease Engineering Pty Ltd – Lend Lease) to design and construct T2E. One of the key elements in this project is the St Helena Tunnel.In order to avoid the steep grades of St Helena Hill, eliminate a well-known accident black spot and maintain the aesthetics of the Byron hinterland escarpment, RMS and Lend Lease prepared designs to construct a 434 m long dual carriageway tunnel, 46 m below the ridge line of St Helena Hill. Lend Lease elected, where geotechnical conditions permitted, to use drill and blast methods to excavate the full tunnel profile, instead of traditional mechanical excavation techniques.Since all blasting locations (both inside and outside the tunnel) were in close proximity to nearby residents, the NSW Department of Planning and Infrastructure imposed strict air blast overpressure (airblast), ground vibration (vibration) limits and limited working hours. Both RMS and Lend Lease recognised that these restrictions meant that nearby residents may be exposed to blasting activities for longer than was necessary. As a result, after close consultation and agreement with the nearby residents, RMS applied successfully to the NSW Department of Planning to increase the airblast and vibration limits, as well as the working hours.Working under these new conditions, Lend Lease employed a range of best practice drill and blast technologies provided by both Orica Australia Pty Ltd and Atlas Copco Mining and Rock Excavation to improve the safety and efficiency of blasting activities and to minimise the potential negative impacts of the blasting works on affected residents. These technologies included: the use of a continuous environmental monitoring system to record the results of the blast events and provide quick and easy reporting to key stakeholders to address RMS specification requirements electronic detonators to enable accurate hole detonation timing for vibration compliance and to give project engineers the flexibility and precision to alter each design to suit the geological profile of each face the use of two software programs and advanced drill rigs to enable the efficient design of blasts, electronic transfer of designs to the drill rigs, as well as in-hole monitoring and recording of drilling performance the use of a specialised bulk emulsion system to deliver fully coupled bulk explosives into face blastholes to maximise fragmentation, and decoupled bulk explosives into perimeter blastholes, to reduce overbreak and deliver a cleaner profile.By taking a progressive approach towards the environmental restrictions and the work hours imposed, as well as utilising best practice blasting techniques, RMS and Lend Lease were able to blast with confidence and achieve their production deadlines and reduce the total cost of the project.Most importantly, RMS and Lend Lease were able to meet their environmental obligations and work constructively with the nearby residents to ensure that the blasting was undertaken as safely and efficiently as possible without delay or negative impact.CITATION:Dowling, M, Domotor, R and Miller, D, 2014. Improving excavation efficiency at the St Helena Tunnel using best practice drill and blast techniques, in Proceedings 15"

Sep 17, 2014

The Vertical Crater Retreat (VCR) mining method was used to mine two rib pillars at New Broken Hill Consolidated Limited (NEHC) mine at Broken Hill. Experience gained in a trial VCR pillar stope was applied to the design of Panel 3CN pillar (P3CN). Restricted access and a central sandfilled plug in this pillar necessitated the use of angled blastholes and blasting of the stope in two sections. Borehole surveys and close charging supervision were necessary to block, charge and stem the spherical charges in the correct position. The laver sections of the VCR stope with rock walls attained an average slice advance of 2.2 m whereas the higher section of the st.ope between cemented fill walls attained an average slice advance of 3.4 m. Achieved fragmentation was extremely fine. External dilution was assessed at less than 10 per cent. A cement consolidated sandfill exposure of approximately 1300 m2 stood vertically with no significant slumping.

Jan 1, 1983

By O N. Antzutkin, A V. Ivanov, W Forsl

Polycrystalline and surface complexes (at synthetic sphalerite, ZnS, and galena, PbS) of zinc(II) and lead(II) ions with eight different O,OÆ-dialkyldithiophosphate (Dtph) substances have been prepared and comparatively studied by means of 31P CP/MAS NMR spectroscopy. The 31P resonances have been assigned to dithiophosphate groups with terminal S,SÆ-chelating or bridging coordinations in the mono-, bi-, tetra- and polynuclear complexes respectively. The bridging coordination of two neighbouring zinc(II) ions by O,OÆ-dialkyldithio-phosphate ligands was established at the surface of synthetic sphalerite.The adsorption mechanism of dialkyldithiophosphate on synthetic galena includes formation of a surface complex as well as surface precipitation. Principally different coordination modes of the reagent were discovered at the surfaces of galena and sphalerite (ie terminal S,SÆ-chelating coordination to the lead atom).Derivatives of monothiophosphoric and phosphoric acids were displayed as hydrolysis products of dialkyldithiophosphates at synthetic PbS.

Jan 1, 2005

By J deVries, A Broodryk, P Kyselica, K McLean

Gwalia gold mine is located close to the town of Leonora in the Goldfields region of Western Australia, some 830 km from Perth. The mine is wholly owned by St Barbara Ltd, an Australian Securities Exchange listed gold producer and explorer. The Gwalia mine is a deep, all-trucking mine and is serviced by a 10 km long decline from surface. Mining is currently 1540 m below surface. Reserves extend to 1820 m below surface and are open at depth. The mine produces in excess of 200 koz of gold per annum.The Leonora area is hot and arid, with a mean annual rainfall of 230 mm and a 95 per cent mean daily maximum temperature of 20.3°C wet-bulb and 35.6°C dry-bulb.The primary ventilation system comprises a 490 kg/s surface exhaust fan, which draws air down a parallel intake system consisting of the decline, and a dedicated fresh-air intake system extending to the bottom of the production zone. Cooling is provided via a surface bulk air cooler serviced by an ammonia refrigeration plant that delivers 150 kg/s of chilled water to the bulk air cooler.The refrigeration plant and bulk air cooler were installed in 2008. The design allows cooling to be increased over time by installing an additional refrigeration plant in a lead lag configuration with the current refrigeration plant when required.Since 2008, expansion and increased depth reached a point where the underground heat load exceeded the installed capacity of the existing 4.0 megawatt rated (MWR) refrigeration plant. In order to maintain the mine design conditions underground, upgrading of the existing refrigeration system was required to bring the cooling capacity to 7.5 MWR.Two expansion options were considered: the addition of an ammonia vapour-compression refrigeration machine similar to the existing one or a lithium bromide absorption refrigeration system using waste heat from the site power station. The original design and layout of equipment on-site meant that either could be used, allowing an assessment of the merits of both when additional cooling was required.The decision was made to install a lithium bromide absorption system on the lead side of the existing ammonia refrigeration plant. This arrangement provides considerable economic benefits, including reductions in site-generated electrical power, generator fuel consumption and carbon dioxide emissions.This paper details the planning, design, installation and commissioning of the absorption chillers.CITATION:Broodryk, A, deVries, J, Kyselica, P and McLean, K, 2015. The design, installation and commissioning of an absorption refrigeration system at Gwalia gold mine in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By P Holtham, W Valery, P Baguley, A Jankovic

There is a growing interest in magnetite ores because of the increasing demand for this commodity. With these ores, there is significant cost associated with milling the ore to fine sizes using ball mills in closed circuit with hydrocyclones. Cyclone classification efficiency tends to be poor due to the large difference in density between magnetite and gangue. This decreases the grinding circuit efficiency and results in over-grinding of magnetite. The objective of the work described in this paper was to modify the Bond locked cycle milling test procedure to quantify the loss of grinding circuit efficiency due to the mineral density effect. The locked cycle test procedure described here includes a stage of magnetic separation treating the closing screen undersize, which allows simulation of magnetite classification. The effect of classifier efficiency on low-density particles (non-magnetics) was simulated by altering the proportion of closing screen undersize bypass returning to the mill. Using a magnetic separator and a screen in the magnetics stream, different proportions of the magnetic fraction can be bypassed, thus allowing simulation of the effect of particle density on classification efficiency. This laboratory test work has confirmed that the impact of mineral density on cyclone efficiency subsequently has a crucial negative effect on ball mill circuit capacity. The results are in good agreement with reductions in capacity observed in practice. Multicomponent grinding and classification models were also developed in the LIMN software environment and were able to successfully simulate both the industrial and the laboratory ball mill circuit. The test and modelling procedures established in this project could be used for improved design of new magnetite ball mill grinding circuits as well as the optimisation of existing circuits.CITATION:Jankovic, A, Baguley, P, Valery, W and Holtham, P, 2015. Effect of mineral density for milling magnetite ores, in Proceedings Iron Ore 2015, pp 159–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

During the first five years of operation, the Lihir gold mine has steadily increased plant throughput rate to over 4 Mtpa, well above the original design capacity of 2.8 Mtpa. Understanding how future variations in ore type impact on plant performance has been an integral part of LihirÆs development program. This paper discusses the key drivers for significant improvements to the plant, including a second oxygen plant, a pilot flotation plant, an autoclave heat recovery circuit, a pebble crushing circuit and additional autoclave feed pumping capacity. The result is a process plant with the flexibility to accommodate variations in ore type without significant loss of throughput.

Jan 1, 2003

The Emmaville district is located in the northern part of the New England region of New South Wales some 400 miles north of Sypney. Better known for its substantial production of tin and tungsten ores, the Emmaville district has also been the centre of a small and somewhat sporadic production of copper, arsenic, silver, lead and zinc. This production has come principally from three mines-Webb's Silver Mine, Webb's Consols and, to a lesser extent, Pye's Creek Silver Mine.The ores from these mixed sulphide deposits are texturally and mineralogically complex and the problems of beneficiation are rather formidable.GENERAL GEOLOGYThe main rock type of the Emmanville district is a dark, brown to blackish massive siltstone of Permian age which overlies acid volcanics possibly also of Permian age. In places the siltstone gives way to conglomerates and standstones with discontinuous lenses of calcareous sediments (David, 1887).The whole series is folded but because of the massive character of the more expansive siltstone, detailed structure is difficult to delineate.Toward the close of Permian time the area was intruded by a series of intermediate to acid plutonic and hypabyssal rocks. Mineralization within the region is ascribed to the more acid of these intrusives-granodiorite, granite, and quartz-felspar porphyry (Lawrence, 1957, 1960).No intrusive rocks outcrop in the immediate neighbourhood of Webb's Silver Mine though granite occurs two miles...

Jan 1, 1961

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

By A S. M A Haseeb

Zircon is the second in abundance among the heavy minerals occurring in the beach sand along the coastal belt of Bangladesh. In this study a detailed characterisation of Bangladesh zircon extracted at the pilot plant of the Bangladesh Atomic Energy Commission at CoxÆs Bazar has been attempted using chemical analysis, X-ray diffraction and optical microscopy. From the chemical analysis it is found that Bangladesh zircon has a purity of 95.88 per cent. The main impurity in Bangladesh zircon is titanium oxide (3.01 per cent). This is followed by iron oxide (0.42 per cent). A number of other oxides are also found. Microscopic study revealed that Bangladesh zircon has an elongated, prismatic shape with pyramidal termination in about half of the grains while the rest are more or less rounded. Some fractured and irregular grains are also found. Bulk sample of Bangladesh zircon in the as-received condition shows a yellowish brown color. However, individual zircon grains are seen to be almost colourless and transparent under polarised light. XRD study confirmed good crystallinity in the sample. Under the microscope it is found that zircon grains constitute 94 per cent while total impurities amount to six per cent in Bangladesh zircon. This result agrees fairly well with the chemical analysis results. Microscopic study identifies oxides of titanium (both rutile and ilmenite) to be the main impurity, in conformity with the findings of chemical analysis. Further, monazite was also identified as an impurity under the microscope. An iron bearing coating is also found on a few zircon grains. Most of the impurities found in Bangladesh zircon exist as discrete minerals.

Jan 1, 2000

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Mansouri, M A. Ebrahimi Farsangi, F Faramarzi

A blast fragmentation model is developed based on the gamma function to describe the run-of-mine fragmentation distribution. The model presented is aimed to benefit from simplicity in application and also to be efficient in description of the fine to coarse part of the blast rock fragments. In fact, the gamma based model (KC-KUM), gives a unit distribution curve, which is made up of two separate equations, covering different fragment sizes in the muck pile. The generated values of the fines to central part of the equation and the central to coarse part of the equation are connected at the 40 per cent grafting point. For validation, eight production blasts, which were specially designed for this purpose, were carried out at an iron ore mine (Jalal-Abad iron ore mine/Iran). Results achieved by KC-KUM and two of the most well-known models. Kuz-Ram and Swebrec, are compared with measured data. Moreover, to assess the models’ efficiency in presenting the best distribution curve, a Logarithmic error method is chosen. Based on the achievements. KC-KUM has the least deviations by the least absolute log error of 0.52, whereas the values obtained for the Swebrec and Kuz-Ram models were 0.79 and 1.34 respectively. Furthermore, the models were applied to predict X80 for 12 production blasts carried out at Gol-e-Gohar iron ore mine/Iran. These predictions were compared with the results from these trials. The coefficient of determination (R2) and root mean square error (RMSE) are calculated. Consequently, the highest R2 was obtained for KC-KUM at 0.837 with the least RMSE of 11.31. On the other hand, R2 and RMSE are equal to 0.832 and 20.19 for Swebrec; and 0.813 and 19.75 for Kuz-Ram respectively. The results obtained suggest the superiority of the KC-KUM model over the other two models in assessment and prediction of blast fragmentation in a reliable way.CITATION:Faramarzi, F, Ebrahimi Farsangi, M A and Mansouri, H, 2015. Prediction of rock fragmentation using a gamma-based blast fragmentation distribution model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 685–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The Pasminco mine at Rosebery in north western Tasmania is a medium sized underground base and precious metals mine. In April 1992 a major wedge failure of approximately 5000 t occurred in the backs of a main access drive to the 18 level H Lens orebody. This collapse prevented access to 190 000 t of ore which had been scheduled for production in July - August 1992. At the time of the collapse, the mine was in a transition period between mining small pillar remnants of several other orebodies and developing to the new deeper J Lens orebody.The development at this orebody was behind schedule and it was necessary to find a cost-effective and timely alternative to a 75 m bypass drive around the fall area.A Lysaght- Fletcher multiplate steel arch was available on-site from a deferred surface road project and it was decided to use this arch to regain access through the fall area. Due to the danger of continued minor falls, the entire 18 m long, 3.95 m high x 4.5 m wide tunnel had to be assembled in the 4.7 m wide x 5 m high accesss drive and pushed into the fall area as a single unit.

Jan 1, 1993

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016