Search Documents

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

By C P. C David, J P. T Domingo

Addressing nutrient deficiency, among other factors, is vital to the growth and establishment of plants in mine spoils and tailings ponds. Although several organic amendments are available for this purpose, it is important to determine the appropriate ameliorant for the selected plant species. This research examined the effect of different amendments on the growth and ground cover of Centrosema molle, Calopogonium mucunoides and Sorghum spp. in copper/gold tailings. Plant growth and ground cover drastically increased with the application of organic ameliorants, especially manure. Among the three plants, Calopogonium exhibited the best growth and has shown its capability to establish a dense ground cover even in unamended tailings. Results suggest that the plant species and the ameliorants used in this study could be effective in a low-input approach to mine rehabilitation.CITATION:Domingo, J P T and David, C P C, 2014. Legume and grass revegetation of mine tailings, in Proceedings Life-of-Mine 2014 , pp 525–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Sheer T. J, Van Rensburg J P

The primary objective of this research was to address the demands imposed on self- contained self-rescuer (SCSR) performance dur- ing simulated escapes. The results clearly indicate that SCSR performance, apart from the inherent technological features, is a function primarily of the physical and anthro- pometric features of the wearer, and of the particular nature of the escape route. These factors consequently play a major role in the planning of any escape strategy, which may vary from mine to mine. It is therefore concluded that each mine would have to formulate its own escape strategy which in turn would depend on the choice of SCSR, and the particular escape Route.

Jan 1, 1988

By C Augustin, M Hahn, K Nienhaus

Operators of mining machinery like haul trucks or excavators have very limited information about the exact distance to other equipment as well as to the natural boundaries like berms, walls and structures such as crushers. The industry is seeking solutions to provide safety and positioning. The authors have developed a solution approach which is being used in several installations. This solution consists of three parts: first robust and compact two-dimensional (2D) radar scanners that provide range and angular information of the environment especially under difficult conditions like dust, rain, snow and fog; second an intelligent data processing framework flexible enough to adopt to different machines and operation modes like speed, inclination, visibility, tire friction, GPS position, orientation and acceleration; and third a high quality and easy to use interface giving highly condensed data to the operator, not blinding the operator at night and being sunlight readable. The truth of present proximity detection sensors is that they not only have a high false alarm rate but furthermore cover only a fraction of the possible scenarios. This makes them unsuitable for stand-alone collision avoidance systems. On the other side, mine dispatch systems only deliver database and GPS information, but no information regarding the real environment. The indurad company and its Australian partner CTS (http://www.cts.com.au) addressed these aspects by developing smart productivity enhancement driver assistance tools like lane and crusher dumping assistance.An innovative driver assistance tool developed in cooperation with the coal shearer manufacturer Eickhoff and the RWTH Aachen University has been awarded with the annual research award of its customer RAG, being the largest German hard coal producer, as well as with the bauma Innovation Award in 2010.

Sep 26, 2011

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

By Wylie A. W, Jarrett R. G

Two versions of a radiometric-type caliper for measuring borehole diameter are described. One, based on the bow-spring principle, is suitable for percussion (exploration) drill holes. The other, which utilizes hemispherical wall contactors actuated by springs, is suitable for blast holes. Both utilize low-power radioactive sources and employ a scintillation detector to measure the "inverse-square law" response of the device to changes in borehole radius. The performance of the device is examined and examples of its use are illustrated.

Jan 1, 1976

Over the past 12 years screening of materials has undergone a dramatic change in both the types and materials used in screen mats and the quality requirements of the finished product. With the main thrust now on quality and a cleaner product a different approach was needed in the operation of sizing screens. New screen mats with many different aperture configurations have been developed using rubber and plastics.to replace the traditional screen mat of woven wire or punched plate.

Jan 1, 1984

By J Rutter, D Francois-Bongarcon, M Federov, N Odiar, M Scott

There are two fundamental methods for metalliferous sensing of primary crushed ore available for deployment at operations. These methods can be classed as surface measurement techniques (including XRF, LIBS, NIR, SWIR) or penetrative/semi-penetrative measurement techniques (including PGNAA, PFTNA, GAA, MR). While the individual sensing technologies exploit different physical phenomena to measure metal content, penetrative sensor measurements of grade are often regarded to be superior to surface measurement techniques due to the much larger sampling volume penetrative techniques provide. Surface sensing techniques often utilise simpler, established technologies that have considerable benefits in the speed of analysis, capital costs, ease of deployment, social license to operate and operational safety. This paper investigates whether surface sensing techniques achieve adequate sampling representativity of primary crushed rock mass to provide economic benefit over penetrative sensing technologies for bulk ore sorting applications. The paper details the methodology used to assess whether surface XRF measurements change throughout various stages of comminution, and increased surface exposure, from primary crushed ore (top size of -175mm) to finely crushed product for assay (top size -2mm). The methodology was applied to 2 ore mineralisation styles, across variable metals and grades, to identify any associated opportunities and limitations to surface sensing techniques. The results assist in developing a method to determine if surface sensing and measuring via XRF is an adequate representation of the rock mass for bulk ore sorting applications and identify any associated limitations in particle size distribution, mineralisation or natural deportment strength to guide suitable application of surface sensing techniques.

Nov 10, 2020

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

By Wyborn L, Giddings J. W, Plumb K. A

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

From August 1962 to June 1976 Peko Mines Ltd. produced Gold Bullion at the Peko Control Mill using 18x24 Denver Mineral Jigs and strake tables. Gold ores treated during this period were obtained from Orlando, Juno and Ivanhoe Mines and from the Warrego Mine after 1974, all in the Tennant Creek Area of the Northern Territory. With the downturn in copper prices Warrego Copper ore mining ceased and the copper Smelter closed down in February 1974, Warrego gold ore continued to be treated in the Peko Concentrator.

Jan 1, 1978

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

By C Tonkin, S D. Howell, P V. Johnson, J Moriarty, P W. Duck

This paper presents the scientific framework underpinning the resource valuation and optimisation model (RVOM). The RVOM is a partial differential equation based real options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty, as well as processing capacity constraints. The RVOM can be applied to any multi-ore mine, open pit or otherwise, where the block-order of extraction has already been planned using existing software tools such as the Gemcom WhittleÖ strategic mine planning package. The RVOM can also take account of multiple commodities within a single mine, and multiple forms of price behaviour. The three key outputs from the RVOM are: valuation, optimal decision and probability of decision. A decision takes account of upfront costs, and can include an unlimited number of transitions between: normal operation, expanded operation, care and maintenance and abandonment (and variants thereof). The RVOM then employs stochastic process theory to determine the probability of reaching these decisions. This gives the mine operators clear indications as to where their risks lie, aiding their mine planning. A clear example of the RVOMs usage to a case-study gold mine is presented, demonstrating its broad applicability, the added value it can create and how users can easily make use of the RVOMÆs state-of-the-art algorithmic engine.

Sep 26, 2011

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By M Haest, O Dominguez, D Mittrup

With the current focus in the mining industry on reducing costs, while simultaneously improving ore quality, infrared spectroscopy is a tool that can potentially assist companies to meet both challenges. Changes in the nature of infrared spectra are strongly influenced by changes in mineralogy, which is a key input variable for exploration (geology and orebody modelling and ore characterisation) and mining (pit design, mine scheduling and processing plant design/management).Infrared spectroscopic logging of drill holes has been embedded as a standard tool in BHP Billiton Iron Ore exploration, with a process set up to automatically deliver mineralogy and associated imagery to the end users (typically exploration geologists). The availability of consistent and automated mineralogy drill hole logs across a project is improving the output quality and reducing re-work.BHP Billiton Iron Ore is now looking into using the same infrared spectroscopic data for other applications, including improving predictions of geometallurgical and geotechnical parameters. Trials show that addition of infrared spectroscopic data to conventional data sets (element analysis and depth information) is significantly improving the accuracy of regression models to predict the lump-fine ratio.Further initiatives around infrared spectroscopic data in BHP Billiton Iron Ore include the installation of infrared spectroscopic sensors over conveyor belts, infrared spectroscopic mine face scanning and infrared spectroscopic blasthole logging. The ultimate vision is to have consistent, seamless mineralogical data from infrared spectroscopic sensing available throughout the mineral value chain (exploration/mining/processing). This seamless infrared spectroscopic data ‘bridge’ will allow the transfer of knowledge between the different sections of the value chain (exploration, mining and processing). For example, ore handle-ability could be predicted on exploration samples using regression models built from processing plant observations. In the opposite direction, information gathered about the buried stratigraphy by infrared spectroscopy utilised during exploration, could be used to predict the stratigraphy encountered during mining. This collaboration across BHP Billiton Iron Ore is expected to deliver significant savings, while improving the quality of the final product, thus helping to drive efficiency over the next decade.CITATION:Haest, M, Mittrup, D and Dominguez, O, 2015. Reaping the first fruits – infrared spectroscopy: the new standard tool in BHP Billiton Iron Ore Exploration, in Proceedings Iron Ore 2015, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018