Search Documents

Joseph W. RichaRds, South Bethlehem, Pa. (communication to the Secretary*): The hold experiment of Mr. James Gayley in drying the blast used in the Isabella furnace has attracted the attention of the whole metallurgical world, and has given rise to a wide discussion of the reasons for its great success. Mr. Gayley and the capitalists who backed him in his work deserve congratulations on the success of the venture, not only because it succeeded, but because they have been rewarded far beyond the maximum that could be expected from theory or probability. To state the case in its simplest terms, all that could have been predicted was: (1) that the removal of the moisture from the blaet would result in the saving of the heat required for its decomposition, representing from 3 to 5 per cent. of the heat-value of the coke used; hence about that quantity of fuel might be saved; (2) that the furnace would be somewhat more independent of variations in the weather; (3) that the campaign would be a little hotter; and (4) that the speed of the blowing-eugines would be decreased, at least in amount proportionate to the reduction in temperature of the air led to them. I do not think anyone anticipated a much larger output per day. The results actually attained were: (1) the furnace made an increase of 24.86 per cent. in the output of pig-iron per day; (2) it consumed 19.6 per cent. less coke per ton of pig-iron made; (3) the blowing-engines were run 15.8 per cent. slower; and (4) the saving in power made up for the power required to run the refrigerating-plant. In addition, the blast was hotter; the waste-gases cooler, because of their smaller volume; and there was a greater proportion of carbon dioxide to carbon

Jan 1, 1906

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited ." Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

Jan 1, 1968

By William I. Busenbark, Elmer C. Newman

At Bingham Canyon, the world's largest open-pit copper mine, annual grease consumption is in the neighborhood of 109 000 kg (240,000 lb), all of which was 544 (120-16) purchased, warehoused, and distributed in 54-kg (120-1b) and 180-kg (400-1b) drums. While perhaps a menial and mundane chore, grease distribution shows on the ledger as a significant expense item. To improve labor and cost performance, Kennecott maintenance engineers undertook a study to find the most direct method for moving multi purpose grease (MPG) from the refinery to the point of final consumption. What they found was a direct vendor system for hulk grease so simple and flexible that long-established drum distribution is being phased out in favor of the newer method throughout 75% of the operation.

Jan 9, 1977

By S. G. Gibbs, A. B. Neely

Jan 1, 1967

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11' 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.