Search Documents

By H. L. Gilbert, W. W. Stephens

Production of anhydrous zirconium tetrachloride by direct chlor- ination of a zirconium oxide carbon mixture in a silica-brick-lined chlorinator is described. Theory and thermodynamics of reactions are discussed. A pilot-model chlorinator and full-scale production equipment are described and operating data are included. ANHYDROUS zirconium tetrachloride required as a starting material in the Kroll process for production of ductile zirconium has been produced in this country principally by chlorination of the carbide or "carbonitride" made by reduction of zircon sand concentrates with carbon in the arc furnace. This process and the equipment used have been fully described.'.' It is well known that zircon or badde-leyite ores may be chlorinated directly with chlorine in the presence of carbon, and this one-step approach would seem at first glance to be preferable to the two steps involved in the carbide-chloride operation. As previously discussed1 considerations leading to adoption of the longer process were: 1—Chlorination of the carbide proceeds rapidly at temperatures below 500°C, whereas temperatures above 900°C were considered necessary for chlorination of zircon-carbon mixtures. 2—The highly exothermic nature of the carbide-chlorine reaction makes it self-sustaining, while heat must be supplied continuously in direct chlorination of the ore. 3—Silicon was thought to be chlorinated along with zirconium in the direct chlorination of zircon, leading to high chlorine consumption. In production of carbide in the arc furnace, silicon is driven off as silicon monoxide and does not enter the chlorinator. 4—For efficient direct chlorination, the ore must be finely ground and intimately mixed with carbon, and the mixture briquetted. 5—Direct chlorination requires a much larger chlorinator for a given production capacity than chlorination of carbide. Recently it has become necessary to produce large quantities of zirconium metal from a chemically purified zirconium oxide. Since the cost of the latter is high, the relatively high losses encountered in production of carbide in the arc furnace could not be tolerated, and a graphite resistor furnace5 was developed for production of carbide, which was then chlorinated in equipment previously used for chlorinating arc-furnace carbide. This method of operation was quite satisfactory, and losses in the carbid-ing step were minimized. However, operating costs were relatively high, and the process did not lend itself particularly well to large-scale operation because of the multiplicity of small units required and the hand labor needed to load, unload, and maintain the furnaces. To chlorinate the carbide, a vertical-shaft chlorinator was used in which the charge was heated with a central split graphite-rod resistor.' Operation of this chlorinator was somewhat less satisfactory with the resistor furnace carbide than it had been with the arc-furnace carbide due, principally, to the differences in physical properties of the carbide. The arc-furnace carbide is obtained as a fused metallic-appearing mass which can be crushed to -1/4 in. with production of a minimum of fines, whereas the resistor-furnace product is lightly sintered and produces a large proportion of fines in crushing and handling. These fines tend to pack in the chlorinator and promote channeling. which results in poor chlorine efficiency and low capacity. Data based on production of 22,000 lb of chloride from resistor-furnace carbide in this equipment are shown in Table I. Necessity for increasing production of chloride from about 2,000 to 15,000 lb per week led to further investigation of possible methods for direct chlorination of the oxide or oxide-carbon mixtures. Direct chlorination of the pure oxide presents much less difficulty than chlorination of zircon sand or oxide ores. The oxide is easily ground to —200 mesh, and no silica is present to cause excessive consumption of chlorine or contamination of the product. Theoretical Considerations The principal chemical reactions involved in chlorination of mixtures of zirconium oxide and carbon may be written as follows: ½ ZrO2 (c) + C(c) + Cl2(g) = ½ ZrCl,(g) + CO(g) [I] 1/2 ZrO, (c) + CO(g) + Cl2(g) = ½ ZrCl,(g) + CO2(g) 121 ½ ZrO2 (c) + ½ C(C) + Cl2(g) = 1/2 ZrCl4(g) + ½ CO2(g) [3]

Jan 1, 1953

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By M. E. Wadsworth, K. C. Bowles, H. E. Flanders, R. M. Nadkarni, C. E. Jelden

The kinetics of precipitation of copper on iron of various purity were carried out under controlled conditions. The rate of reduction has been correlated with such parameters as copper and hydrogen ion concentration, geometric factors, flow rate, and temperature. The character of the precipitated copper as a function of flow conditions and rate of PreciPitation has been observed under a variety of conditions. ThE precipitation of copper in solution by cementation on a more electropositive metal has been known for many years. Basile valentine' who wrote Currus Triumphalis Antimonii about 1500, refers to this method for extraction of copper. Paracelsus the Great2 who was born about 1493 cites the use of iron to prepare Venus (copper) by the "rustics of Hungary" in the "Book Concerning the Tincture of the Philosophers". Agricola3 in his work on minerals (1546) tells of a peculiar water which is drawn from a shaft near Schmölnitz in Hungary, that erodes iron and turns it into copper. In 1670, a concession is recorded4 as having been granted for the recovery of copper from the mine waters at Rio Tinto in Spain, presumably by precipitation with iron. Much has been published in recent literature on the recovery of copper by cementation, the majority of the articles being on plant practice.5-24 The rest include articles on investigation of the variables involved25-28 and a review of hydrometallurgical copper extraction methods." This literature has established: a) The three principal reactions in the cementation of copper are Cu + Fe — Fe+4 +Cu [ 11 One pound of copper is precipitated by 0.88 lb of iron stoichiometrically. In actual practice about 1.5 to 2.5 lb of iron are consumed. 2Fe+3 + Fe — 3Fe+2 [21 Fe +2H'-Fe+2 + H2 [3] Reactions [2] and [3] are responsible for the consumption of excess iron. Wartman and Roberson'28 have established that Reactions [ I] and [2] are concurrent and much faster than Reaction [3]. b) Acidity control is important in the control of hydrolysis and the excessive consumption of iron. he commercial workable range is approximately from pH = 1.8 to 3." c) Iron consumption is closely related to the amount of ferric iron in solution. Jacobi" reports that, by leaving the pregnant mine waters in contact wi th lump pyrrhotite (Fe7S8) for 3 hr, all the iron was reduced to the bivalent condition and scrap iron consumption was cut to 1.25 lb scrap per pound of copper precipitated. He also reported that SO2 has been used successfully to reduce ferric iron to the ferrous state. d) The ideal precipitant is one that offers a large exposed area and is relatively free of rust. e) High velocities and agitation show a beneficial effect upon the rate of precipitation, as it tends to displace the layer of barren solution adjacent to the iron and also dislodges hydrogen bubbles and precipitated copper to expose new surfaces. Little work, however, has been published on the reaction kinetics of copper precipitation on iron. Cent-nerszwer and Heller20 investigated the precipitation of metallic cations in solutions on zinc plates. They found the cementation reaction to be a first-order reaction. The rate constant was independent of stirring for high stirring rates and they concluded that the rate is governed by a diffusional process at low stirring speeds and by a "chemical" process at higher stirring speeds where the rate reaches a constant value. This conclusion has been challenged by King and Burger30 who could not find any region where the rate was independent of the stirring speed, although the rate constant they had obtained for high stirring speed was greater than the maximum value of the rate constant reported by Centnerszwer and Heller (by a factor of six). King and Burger, therefore, concluded that the rate of displacement of copper was controlled only by diffusion. Cementation of various cations on zinc has been summarized by Engfelder.31 APPARATUS A three-necked distillation flask of 2 000-mm capacity was used as a reaction vessel. A pipet of 10-mm capacity was introduced through one of- the side necks, the sample of sheet iron, mounted in a rigid sample holder, through the other, the stirrer being in the middle as shown in Fig. 1. The whole assembly was immersed in a constant-temperature bath. The stirrer was always placed at the same depth in the solution. EXPERIMENTAL PROCEDURE Reagent-grade cupric sulfate (J. T. Baker Chemical Co., N.J.) was used to make up a stock solution containing 10 g of copper per liter which was then diluted to various concentrations as required. Experimental data were obtained by measuring the amount of copper and iron ions in solution at successive time intervals. The initial volume of the solution was always 2000 ml, 10-ml aliquots being removed each time for chemical analysis. Because the total volume change of the solution was less than 10 pct, no correction was used for solution volume change. Nitrogen was bubbled through the solution before and

Jan 1, 1968

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By J. W. Rutter, K. T. Aust

The migration of individual, large-angle grain boundaries has been studied as a function of tempereature and solute concentration in specimens of zone i.e filled lead containig very small additions of silver and of gold. Tile results are compared with various the-ories of grain boundary migration and with observations made prev.iorlsly of grain boundary migration in similar specimens of zone-refined lead containing tin additions. A previous investigation by the authors dealt with [he temperature dependence of grain boundary migration in bicrystals of zone-refined lead containing small additions of tin.' It was shown that tin additions as low as a few parts per million cause a large decrease in the grain boundary migration rate at any given temperature, as well as a marked increase in the temperature dependence of the migration rate. It was found that existing theories of grain boundary migration. based on the motion of dislocations. or upon the concept of atom transfer in groups across the boundary (group process theory). or upon the control of grain boundary motion by volume diffusion of impurity atonls along with the boundary. are incapable of accounting for the observations. The single process theory of grain boundary migration. which is an absolute reaction rate calculation based on the transfer ui atoms singly across the moving boundary, was found to predict the migration rate reasonably well for a number of boundaries whose motion was shown to be very little influenced by impurities, but not for boundaries whose illation was influenced markedly by impurities. It was concluded that the elementary process of grain boundary migration involves the activation of single atoms during transfer across the boundary. and that inadequate knowledge is available to permit the influence of impurities to be properly taken into account. The present study was initiated to check the validity of the above conclusions with other alloy systems, namely high-purity lead with small additions of silver and of gold. Both silver and gold diffuse faster. and with a lower activation energy of volume diffusion. than does tin in lead;' consequently, a study of the effects of silver and gold on grain boundary migration in high-purity lead offered a means of testing theories of boundary migration based on bulk diffusion of the solute (eg. ref. 3). In addition. it was hoped that the present work, in comparison with the results for tin in lead, would provide information concerning which factors are important in determin- ing the interaction between solute atoms and a grain boundary. EXPERIMENTAL PROCEDURE The preparation of bicrystals of zone-refined lead, with various silver or gold additions, was identical to that previously described for the lead-tin alloys.''4 Each bicrystal consisted of a striated crystal which was grown from the melt. and an adjacent striation-free crystal which was introduced by artificial nucleation and growth.''4 The striation or lineage substructure in the melt-grown crystal provided the driving force for grain boundary migration. During the preparation of striated single crystals by growth from the melt, it was found that silver or gold concentrations as low as 2 or 3 ppm by atoms were sufficient to cause formation of the hexagonal cell structure. which is due to the presence of impurity, during freezing. This structure is revealed on the solid-liquid interface by decanting the liquid during freezing. The hexagonal cell structure was observed previously4 in zone-refined lead crystals with tin contents above approximately 200 ppm by atoms. These concentrations of silver, gold, or tin are in agreement with the predicted amounts required for cell formation in lead,5'6 under the present conditions of freezing.4 The absence of cell structure at decanted interfaces, therefore, served as a useful indication that the silver or gold contents were less than 2 or 3 ppm by atoms in the specimens as grown. It was found that grain boundary migration occurred only very slowly when the solute content approached that necessary for cell formation. As a result, the present experiments were conducted with silver or gold additions less than 1 ppm by atoms. This impurity level is well within the solid solubility limits for silver and gold in lead.7 The annealing treatments, measurements of grain boundary velocities, and orientation determinations were carried out as described previously.' However. each bicrystal was also chemically polished in a solution consisting of 8 parts glacial acetic acid and 2

Jan 1, 1961

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By R. C. Dalzell, A. E. Wells

In 1866, Thomas Graham1 called attention to the volume of gases, three times the volume of the sample, evolved from a meteoric iron heated in an evacuated porcelain tube. From that time to this the occurrence and significance of gases in metals have been the subject of investigation by many workers, among whom Sieverts,2 Iwasé3 and 0. W. Ellis4 stand preeminent. Sieverts and Iwasé concerned themselves with the solubility of a number of gases in metals in the liquid and solid states. They determined the absorption coefficients of these gases, and in all cases found a sharp change in solubility at the melting point of the metals. Ellis analyzed the gases evolved by solidifying copper and those occluded by the solidified metal. Lobley and Jepson5 endeavored to determine the effects of hydrogen, carbon monoxide and nitrogen on the porosity of copper that was allowed to solidify in the presence of each gas after 30 min. exposure to it in the

Jan 1, 1930

By C. F. Kaiser, T. J. Roberts, I. A. Thomson

The Broken Hill Pty. Co. Ltd. grate-kiln pelletizing plant located at Whyalla, South Australia, produced a total of 250,000 tons of fluxed pellets during 1970. More than 180,000 tons were exported to Japan, while the remainder was used in B.H.P. Co. blast furnaces. The pellet plant treats high grade hematite ore fines and has a nominal capacity of 1.5 million tpy. The induration equipment includes a grate 12-ft 2-in. wide by 164-ft 1-in. long, a kiln 18-ft 6-in. diam by 118-ft 8-in. long, and a rotary cooler 50-ft mean diam by 7 ft wide. Operating problems encountered in the production of fluxed pellets are detailed. The most significant aspect of the trial was the increased production, from about 5100 tpd up to a maximum of 7100, brought about by the addition of artificial magnetite to the plant feed. Laboratory evaluation of fluxed pellets showed that pellets having a basicity ratio (CaO to SiO2) in excess of 1.2 have excellent physical qualities. Reducibility and compressive strength after reduction were both higher for these fluxed pellets than for normal acid pellets. Although it was not possible to publish blast furnace operating data, blast furnace trials on fluxed pellets indicated that production was higher and dust losses substantially lower, compared with similar operations on acid pellets.

Jan 1, 1973

President-Mrs John R C Mann, 90 Edgemont Road, Scarsdale, N Y First Vice-President-Mrs C P Pollock, 27 Dante Street, Larchmont, N Y. Second Vice-President-Mrs Mendum B Littlefield, 40 Lincoln Street, Larchmont, N Y Third Vice-President-Mrs J B Cunningham, 236 East 2nd St , Tucson, Ariz Fourth Vice-President-Mrs Theodore Loftus, 410 Cowles St, Fairbanks, Alaska Fifth Vice-President-Mrs George L Craig, 109 Calumet Avenue, Calu¬met, Mich Recording Secretary-Mrs Arnold H Miller, 601 West 115th St, New York 25, N Y Assistant Recording Secretary-Mrs R J Mechin, 66 East 79th St, New York 21, N Y Corresponding Secretary-Mrs John A Poulin, 4 East 70th St , New York 21, N Y Treasurer-Mrs Robert W Rowen, 29 West 39th Street, Room 914, New York 18, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 1000 Park Avenue, New York 28, N Y Assistant Treasurer-Mrs Roger H Sherman, 8 Roman Avenue, Forest Hills Gardens 75, N Y.

Jan 1, 1957

By John B. Hastings

TEN miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; but this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. his section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September and October, 1906, but was quite absorbed in the sampling. I looked, however, for terraces on the rim-rock and other evidences of movement and erosion, but did not find anything to denote an earlier age than the Quaternary. The granite rim-rock may be Archean; S. F. Emmons says that some of the granites in central Colorado are as old as that. The rim-rock as observed is a gray quartzose biotite-granite, except a small area in Sections 3 and 34, where it is a felsitic (?) breccia. The breccia is silicified by solfataric action at the corner near Shaft No. 7, in Section 34; but this action is older than the sands and does not extend to them. The shaft averaged 50c. per ton, more than twice as much as the rest.

Jan 5, 1908

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969

Jan 1, 1916

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.&apos; Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:&apos; Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By Enrique Hauser

FiRE-damp is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.—Methane being a paraffin is characterized by its weak chemical affinities. Prom the physiological point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CHI. I have tried this on myself, making the gas exhaled from the lungs burn subsequently in a Bunsen burner.&apos; From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.—A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.8 Let us recall the nature of this retardation: When a mixture of combustible gases with air or with oxygen is

Jan 1, 1916

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.&apos; Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a&apos; is observed. Previous

Jan 1, 1957

By Eugene A. Alexandrov

The Minister of Geology of the Soviet Union P.Ya. Antropov, recently visited China and claims that this country occupies one of the foremost places in the world in reserves of tin, tungsten, molybdenum, antimony, iron ore, coal, and phosphates. Occurrences of economic value of chromite, nickel, gold, beryllium, tantalum, niobium, rare earths, and asbestos have also been reported. MINERAL RESOURCES Coal: The inferred reserves of coal are estimated at at 1,500 billion tons. A considerable part of the coal reserves is represented by coking coal, 80% of which is bituminous. Thicknesses of coal seams range up to 150 ft in the principal deposits located in northern and northeastern China. The total output of coal in 1958, 270 million tons, was produced by an army of 20 million people mainly in small mines operated by the agricultural communes. Modern hydraulic mining is applied besides primitive, obsolete methods and equipment

Jan 3, 1960